Auto & Truck Parts For Sale

New unused! six oh 2 9 oh 7 8582 text please

I have been backwards engineering 1st gen parts and printing them. This is my current stock. Material is PETG (better durability and higher temp than basic PLA, think water bottle material) These have been test fit in my 1st gen, Stripe, so I know they work. These are unfinished so you can finish and paint them according to what you want. I suggest sanding and self-etching primer before paint. There may be some small defects from the printing process, but these do not affect functionality of the part. Current stock: 1st Gen Passenger Air Vent Surround - Black PETG - Unfinished - $35 ea

Well it's time to purge guys. Looking to move shop in the next year or so and need to clean up my extra junk instead of move it. I've got a ton of stuff and will be constantly editing my first post. No catalytic converters available. Anything bigger than say 24x24 will be local pickup in VA beach, VA. I can sell whole trucks cheap if wanted for a swap. Can arrange east coast shipping if needed. Parting a 2001 Explorer v8 awd, 185k mi still runs and drives. Damage to right rear door, quarter and hatch. XLT trim, tan cloth interior. Black in color. Completely rust free, have title, would sell whole for $1250 Parting a 2000 Explorer v8 awd, 200k mi still runs and drives. Interior is somewhat rough from sunroof leak and sitting. Previous...

I have a complete 1994 T-Bird Supercoupe engine for sale. This is a complete engine with ~43,000 km on it. This was going to be installed in a project Mustang but I sold the car and need the space. Comes with wiring harness and ECM. I also have the matching 4R70W. If you want to use this in a 4x4, I was originally going to put this in my Explorer but never did so have a brand new 4wd tailshaft for the transmission as well as a 4wd tail housing and a B-W 13-56 Touch Drive transfer case. - 3.8L Supercharged engine $2100 - Supercoupe 4R70W $900 - 4R70W/AOD 4wd tailshaft $300 - 4R70W/AOD 4wd tail housing $100 - B-W 13-56 touch drive $400

I have a pair of brand new U-bolt and shock skid plates specifaclly made for the rear of a 1st or 2nd gen Explorer. They are 1/4" plate and protect your u-bolts and raise the shocks up a few inches. These are made for 5/8" U-bolts which are bigger than the stock ones so if you dont have 5/8" ubolts now would be the time to upgrade. These may cause shock to swaybar mount interference so shocks should be mounted body side up or if you have removed the rear swaybar it is a non-issue. Also note these raise the shock up 2"-3" so shock length could be an issue depending on your lift and shock length. Current price for a pair is $215 shipped to the US due to the high cost of steel right now.

I have 2 pairs of stock 1st Gen coil buckets up for sale. I was going to mod these out with the F250 shock towers but just don't have the time to do it so no use for me to keep them. They are in fair shape, some grind marks around the rivet holes and peeling paint but no major rust. 1 bucket has a partially broken spring tab but should not cause any issues. $20/pair + shipping SOLD SOLd SOLD

Used k&n intake kit w/maf sensor. Good used condition, filter has some wear but has a few miles left. Can't guarantee the maf sensor but I'm sure it's fine. $120 shipped in the lower 48

Have a pair of clear euro 2nd gen corner lights. They are OEM Ford units made for Export. The bulbs are different than factory but I've included all the plugs you need to do the swap. These are 20 years old but still look good compared to aftermarket clear corners that yellow in 3 years. $80 shipped in the lower 48

Factory ifs tie down point for Export Explorer and Rangers. Very easy to install, retaining bracket slides in and 3 bolts hold the tie down point snug to crossmember. This is the only one I've seen. $70 shipped in the lower 48

I've got quite a few parts to get rid of from my ongoing 2016 Ford Explorer Police Interceptor Utility project. Some pictures, and some items still need to be photographed. 1. Both front black bucket seats(cloth) 2. Basically the whole factory cat back exhaust. I have the factory mufflers and Flowmaster mufflers with tips welded onto them. Willing to seperate. 3. Civilian console floor shifter and handle. 4. Terrain knob/dial 5. Factory radio. Sync 1. Manual climate controls front and rear. Faceplate, Bezel, 4" screen. (Installed Tesla android radio. Right now the audio control module is still in my dash but think I can remove it for sale too....tbd. 6. 3 quart water methanol reservoir. 7. 5 litre water methanol reservoir 8. Custom...

Sold my 3.5 NA Explorer XLT a couple months ago, and unmarried this from my truck before trading in. Buyer will have to pay to marry this to their truck, as well as whatever tunes you want to load, so just an FYI. Work with LMS on what it'll cost to get you tuned up, and I'll try to save you some $$. I don't know what that cost is going to be for you, so I'll start at $150 shipped lower 48 - if that's too high, I'll try to work with you. I know I spent ~$575 for this SCT with 3 tunes.

For sale I have a Explorer Express Supercharger Kit for 1996-2001 Ford Explorer's with the 5.0 V-8. Obviously this kit will work on any 5.0 with explorer FEAD and running coil packs. This kit is NO LONGER IN PRODUCTION, and this is most likely the LOWEST mileage kit out there. I purchased this kit early this spring for my V-8 swapped Ranger from a member of a Ranger forum. He purchased it BRAND NEW in Spring of 2009 and ended up going a different route and never used the kit (Pictures of the kit when new below). The engine I installed it on was a 1998 5.0, in a 1998 ranger, install was EXTREMELY smooth and painless. I've put about 3,000 miles on the setup, and it hasn't missed a beat minus a Crank sensor that failed on me (this...

Evening, for sale is an Advanced Adapters conversion kit that adapts the 60* 700r4 to the Ford 4.0 OHV. The tail housing is also included. The transmission was supposedly rebuilt when I purchased it but I have no way to confirm that. A B&M shifter is also included. I purchased this transmission and kit from JTX on the board years ago and never used it. The torque converter and mounting hardware are not included. I will post pictures when I get home. 1k O.B.O. You can text me if you would like (9two8)three08-777five. The transmission is located near Prescott Arizona but I am will to meet an hour or two away. Thank you for looking all.

I have a complete PATS system for sale. Everything you need is here. Came out of '01 Sport SOHC AUTO 2WD. Includes: ECU PATS Module RAP module (keyless entry) PATS Key (only have the one) Matching ignition and door locks $350.

For SALE: Excellent set of tires & wheels from a '17 PI Utility. Wheels are OEM 18x8 steel, gloss black finish. Tires are Firestone Firehawk PVS 245-55VR18. Tread wear is exceptionally consistent across all four tires. Average tread depth is .214", about 62% of the original .340" value. These are one of the highest rated all weather/winter pursuit tires available. Review: [ www.prioritytire.com/blog/firestone-firehawk-pvs-review/ ] Sales Sheet: [ www.prioritytire.com/by-brand/firestone/firehawk-pvs-tires/ ] Priced at $600. includes the full set of lug nuts and if you want, the four OEM full size plastic silver colored wheels covers. (This is why the paint finish looks new on the wheels, since they were always protected from...