Recent content by 99SportX | Ford Explorer Forums - Serious Explorations

  • Register Today It's free!

Recent content by 99SportX

  1. 9

    Muffler idea's for a 98 5.0

    Don, by some odd coincidence, I had a video come up on my youtube suggestions tonight. A magnaflow engineer made the exact same claim; that being the muffler will flow better than a straight pipe at high flow rates.
  2. 9

    Muffler idea's for a 98 5.0

    That sounds like a lot of work. You will probably have to cut it open and then weld it back closed, and who knows how it will sound when its done.
  3. 9

    PCM tuning options

    Ok, Lasota sounds like a no brainer then. Paying for an experienced tuner is something I do consider worthwhile because it can cost you a whole lot of money if the engine melts from a crap tune. I am planning to keep the bottom end stock, maybe cam/heads, but most likely a supercharger of some...
  4. 9

    PCM tuning options

    What’s out there these days for stock 5.0 PCM tuning options? I have an old SCT X3 with tunes from Henson Performance but I believe those are as good as useless now since he is no longer doing tuning? I would like the option of being able to do my own tweaking but still use a software that has...
  5. 9

    Muffler idea's for a 98 5.0

    I just ordered up a Borla last night before seeing this thread. The Borla is supposed to have relatively low drone at cruise but a nice growl. I got a dual 2.25” in with single 3” out. Going to make my own pipes out of aluminized since I have a lot on hand in 2.25 and 3. I am using v band clamps...
  6. 9

    Replacement hub mounting bolts

    Thanks all. Any bolt of the same grade would likely suffice but I like the flange head style of the stock bolt. Those are a little harder to find. With the original bolt I can torque it to the book spec and know I am good. I am converting a XLT 5.0 2wd to AWD using the old setup from my Sport.
  7. 9

    Replacement hub mounting bolts

    I didn’t find the part number but solved my issue in a different way by obtaining some used factory bolts.
  8. 9

    Replacement hub mounting bolts

    Does anyone know the ford part number for the three bolts that hold the hub to the knhckle? Or perhaps an aftermarket OEM alternative? I am in need of replacements. I scoured this site and others to no avail.
  9. 9

    5.0 Explorer cam options

    I would just like to add that I ran the 35-349-8 comp cam in my sport like Boomin’ has. I always felt like it lacked grunt up top in the RPM range. It pulled like hell off the line but seemed to struggle once out of first gear and running higher RPM. I had the TM headers and 3.73 gears with a...
  10. 9

    PTU Problems

    It is definitely a bit concerning. While the dealer is taking care of me and replacing the PTU and part of the transmission case under warranty, it just makes me wonder when it’ll happen again. I am going to inquire with them about PTU fluid change intervals for increasing the lifespan. I have...
  11. 9

    PTU Problems

    Anyone ever have a PTU explode? I bought a 16 limited, CPO with 32k miles back in December. It’s at 33k now. Today I was cruising at 60 and felt a few light lurches, almost as if the engine was misfiring. I turned off cruise and coasted for a little bit and it was still doing the same. I pressed...
  12. 9

    '99 Explorer LS Swap Finished - Was has anyone done it?

    Nothing really new to update. It’s cold and snowy right now so all the car projects are hibernating. I will be doing dyno tuning in the spring to get it running better. It runs pretty poorly right now. I am also battling some cooling system issues but that could partially be related to the tune...
  13. 9

    Balance Shaft myth debunked!!

    You need to plug the open oil passages where the balance shaft bearing blocks bolt to the block if you do that. If not, the motor won't last long. While I sold my 99 XLT last october, it is still running great 8 years later without a balance shaft. My cousin is driving it as his first car.
  14. 9

    '99 Explorer LS Swap Finished - Was has anyone done it?

    Thanks. I hear you on the ford vs. chevy thing. It was hard to come to that decision. It makes me a little sad but then I floor it and the sadness goes away. :D That sounds like a cool build but very challenging. I know many have talked about doing a 4.6 over the years but I don't believe I...
  15. 9

    '99 Explorer LS Swap Finished - Was has anyone done it?

    Sorry, guys. I haven't been real great about supplying info on this project. It is a large project but really wasn't that terrible. What made it terrible was me pulling the 5.0 out and having it on the track with the 6.0 in ~3 weeks. haha I did complete a good chunk of the fabrication and...
Back
Top