Recent content by Brett

Hey I'm a legend too :) At that run in 1999, my 94 sport was all stock. I had just completed a rear disc brake swap, which was the basis for one of the original tech articles on this site. Shortly after, I installed a lift, tires, lockers, gears. Those were the early days and things have...

Just tossing this out there since it looks like the tentative dates are set for September. There is a Bronco event at the same time in the Buena Vista area. Bronco Super Celebration (WEST) | Bronco Driver September 7-10, 2022 We have taken our Bronco to this event for the past 2 years. It's...

SOLD!

It was in an early Ranger v8 swap. It is for the earlier transmissions with the removable bellhousings. Here's a link to how it works. https://www.therangerstation.com/tech_library/pdf_documents/712541.pdf

I will have to look up my wiring notes for this. I've had mine wired in since the conversion and it has never had a cam position code. I believe all 94's do have a cam sensor as do some 93's. In the EEC IV, the cam sensor is used mainly as a reference for the computer to fire the correct...

Of course you would be able to make it clear with custom motor mounts and a spacer.... I am referencing the stock motor mounts. They will not allow the factory SOHC pan to clear the Gen1 cross member.

The SOHC pan would hit the factory cross member on a 4x4 frame. The OHV pan is shaped differently to go around the cross member. When changing to the OHV pan, be sure to pull out the balance shaft on the bottom of the SOHC motor if it has one. Not all SOHC engines have them, but mainly if...

Yep!

You will need to pay attention to pin locations and wiring + - when using the sensors. I used a combo of 04 and 94 sensors. MAF - use one compatible with a 93 computer. IAC - use the SOHC as this is usually tied to the intake you are using. CPS - Use the 93 sensor Cam sensor - if you have this...

Cool. I'm more familiar with SCORE and BITD as I work on some of these trucks. Let me know if your 93 has a cam sensor and egr or not.

If the C4 is bolted to the OHV now, it will bolt to the SOHC. I assume that it is using a C5 bellhousing. There is 1 bolt that is not the same on the top RH side of the motor between the OHV and SOHC patterns. Which series are you planning to run this truck in? Best in the Desert / SCORE / etc.?

There is a ton of wiring that needs to be changed. Mine is a 94 Explorer and I used an 04 Ranger. There are a ton of differences between 93-94 and CA and 49 state emissions. Also the SOHC motor had a number of changes between 97 to 12. Lets start with what year donor motor you are using...

Hi Stic-O. I can give you all sorts of details on this swap. There is a lot involved for you to physically mount it in the chassis. The SOHC is tighter against the firewall than the OHV. The motor is physically larger b/c of the heads and intake, so most of the challenges are going to be...

@Spudhut - the tcase you will want to use is 01-03 Sport, 01+ Ranger, 01-05 Sport Trac. Get the tcase, shift motor, 4x4 CM, and as much of the wiring from the 4x4cm as possible. Depending on the donor, the 4x4cm may be in the RH kick panel, or behind the stereo in the dash. It's possible to...

Hi spudhut, I've been out at SEMA this week. On your manual TC swap, you can tap the wires in the GEM for the 4x4 high and 4x4 low lights. On the tcase, it should have a switch and when you pull it, get the plug and some wiring. GEM connector C282 pin 14 (GY) - 4x4 high indicator pin 10...