Dismiss Notice



Register Today It's free! This box will disappear once registered!

CDW6212R's Recent Activity

  • Searches ExplorerForum.com
    1. CDW6212R liked SupaSwope's post in the thread Rear wipermotor help!.

      It was a long process to get my rear wiper to work. First like yourself my back hatch didn't even open. I replaced with a new hatch from...

      January 23, 2018 at 4:23 PM
    2. CDW6212R replied to the thread Rear wipermotor help!.

      The Dorman 38445 striker is the right door unit that most parts stores carry. I think all of the HELP section bushings in a variety...

      January 23, 2018 at 1:40 PM
    3. CDW6212R replied to the thread Oil Change interval.

      I have not seen oil analysis results from oil run through a bypass filter, versus a common 15-20 micron filter. But I have zero doubt...

      January 23, 2018 at 12:09 PM
    4. CDW6212R replied to the thread Rear wipermotor help!.

      Ditto, and one other thought. There were two blade lengths, 14" and 15", don't use the longer one. The 14" wiper works fine and doesn't...

      January 23, 2018 at 11:59 AM
    5. CDW6212R replied to the thread Swapped out PATS computer with non-PATS computer - 1998 5.0 AWD it works.

      Thanks for the info. I don't need it for my 98 PCM but both of my 4406's have something on them. I'm considering using a later Mustang...

      January 23, 2018 at 11:28 AM
    6. CDW6212R liked delexploder's post in the thread Swapped out PATS computer with non-PATS computer - 1998 5.0 AWD it works.

      you gotta be careful with the 4406 the speed sensor needs to be the gear driven one if your going with the 96/97 explorer setup , pull...

      January 23, 2018 at 11:27 AM
    7. CDW6212R attached a file to the thread Headers and exhaust for 97 mountaineer 5.0l.

      Slow too. Here's a picture of someone's two tail pipes under the back, or just two mufflers back there. [ATTACH] [ATTACH]

      Explorer dual tailpipes.jpg 14802Duals.jpg January 23, 2018 at 11:25 AM
    8. CDW6212R liked Mbrooks420's post in the thread Headers and exhaust for 97 mountaineer 5.0l.

      Better late than never.......

      January 23, 2018 at 11:10 AM
    9. CDW6212R replied to the thread Swapped out PATS computer with non-PATS computer - 1998 5.0 AWD it works.

      Wait, you want to use the Explorer PCM, or you have it in place etc, with the harness and trans, but you want to remove it all to run a...

      January 23, 2018 at 11:00 AM
    10. CDW6212R replied to the thread Swapped out PATS computer with non-PATS computer - 1998 5.0 AWD it works.

      Jon, the 98+ BW4406's have the VSS sensor, that changed one year later in the bigger Ford's. I just got a spare TOD version, to rebuild,...

      January 23, 2018 at 10:55 AM
    11. CDW6212R replied to the thread Oil Change interval.

      Oil life is not as simple as a mileage figure, or what some computer tells you to do. The quality of oil is very important, but the...

      January 23, 2018 at 10:49 AM
    12. CDW6212R rated Sgt1411's post Disagree in the thread Oil Change interval.

      I dont have the knowledge in this area so I asked the actual Ford Engineers who worked on this 3.5 V6 about the Ford Oil Life Monitoring...

      January 23, 2018 at 10:32 AM
    13. CDW6212R replied to the thread Rear wipermotor help!.

      Ditto, the door ajar lights up when any of the door latches or either hatch latch isn't fully engaged. Usually that the striker bushings...

      January 23, 2018 at 10:30 AM
    14. CDW6212R replied to the thread Yet another no start/fuel pump question.

      Good point, there are far more parts sources than there used to be. There are always brands I've never heard of when I search for parts....

      January 23, 2018 at 8:30 AM
    15. CDW6212R liked decipha's post in the thread Yet another no start/fuel pump question.

      be mindful that a bunch of the cheaper ful pumps on ebay lack check valves so they bleed pressure as soon as the pump stops priming, its...

      January 23, 2018 at 8:29 AM
    16. CDW6212R replied to the thread Yet another no start/fuel pump question.

      That is unusual, but it's good you figured it out. The inertia switches are very reliable, you'd have to hunt for ages to find 2-3...

      January 23, 2018 at 7:20 AM
    17. CDW6212R replied to the thread M90 rebuild (rudy).

      Gotcha, that's great. It didn't hit me that you meant the check valve is needed to keep the pressure up at the startup. I like that...

      January 23, 2018 at 7:18 AM
    18. CDW6212R liked jd4242's post in the thread M90 rebuild (rudy).

      Battery is behind seat [ATTACH] Switched power fuse block is behind glove box [ATTACH] And this runs from the battery with fuses and...

      20180122_210413.jpg 20180122_210322.jpg 20180122_210253.jpg January 23, 2018 at 7:15 AM
    19. CDW6212R attached a file to the thread M90 rebuild (rudy).

      You should be able to run that big relay with the normal pump relay trigger wire. That's what I thought you had done already. If you...

      95CVPowerDbox02.JPG 95CVPowerDbox01.JPG January 22, 2018 at 8:46 PM
    20. CDW6212R replied to the thread M90 rebuild (rudy).

      That sounds very good. That's smart to have the pump and gauges tied together. You're using the same trigger signal to trigger the relay...

      January 22, 2018 at 5:12 PM






    We Support Our Troops!