Search results

Ok, thanks for the reply, I thought I was missing it somehow. In that case does anyone have any suggestions or experiences with either? I've thought about getting 2nd gen seats, but for the prices I've seen (and condition) I think I'd rather go with aftermarket. As for the steering wheel, the...

I remember looking through a parts review forum awhile back but can't locate it. Is there still one up? I'm looking into aftermarket seats/steering wheel for my 92', and was hoping to see what others have gone with and what's worked well.

I bought an adapter off Amazon and ran into the same problem. The harness for the power fit perfect, but the one for the speakers wasn't even close. Best buy had the same harness as the one I bought off Amazon. I ended up cutting the plug off ( vehicle end) and used crimp butt connectors for...

I wasn't measuring drop correctly... Not sure how to delete this thread( pitman arm is within spec.)

I just removed my stock Steering linkage to replace with the Superlift super runner system. I have a 4" rough country lift installed. The the pitman arm specs. on the instructions for the super runner say the max drop is 3.064". but im measuring closler to 4" drop on my pitman arm (which makes...

Finally going to have matching gears this week.. 7 months with no 4WD. Wooo hoo

I only used the axle shaft. And replaced the bearings with new. I don't remember why it took me three trucks to get to.. But the practice saved time in the drive way. I also found a pair of good seats from a 97. I think I might go with those since they should be a direct swap. The only thing is...

That's a good idea.. I broke my front axle shaft replacing the U joint. I got the replacement at pick N pull. While there i ended up pulling out the wheel bearings on three different trucks. I felt like a pro at home when it came time to do my own.

That would be cool. My main concern was pretty much dimension (between center console and door. And fittment onto my 92 track. For $85, driver and passenger, I figure is worth a shot. Thanks.

Did you end up swapping for newer seats? I'm picking up a pair of 05's for my 92 this weekend. Hoping it'll work out.

Thanks. I'm going to look into getting an extended cable made.

Getting regeared tomorrow!

I have the same issue. After my lift i don't have enough cable coming from the pedal to hook back up. I backed off what i thought was the adjustment nut, but nothing changes.. And if i pull on the rear conection only the driver's side engages. But now i realize I'm missing the the large spring...

Hey guys. I recently purchased the superunner system, but have not installed yet. Would you suggest making this modification prior to the initial install? Also my lift is a rough country 4". I keep reading that the superunner system only works with superlift lift kits without fabbing a new...

Ok, thanks I appreciate the info.

I've been working on reviving my suspension and steering on my 92' eddie bauer. I replaced the front shocks, coils, rotors and wheel bearings. About a week after I got an alignment I started to hear a pretty high pitched "Whirr". It gets Louder and higher in pitch as I accelerate and winds down...

Cool, well Now I know I have Grade 8 Jinn Her bolts. :thumbsup:

Awesome, Thanks, They do have the six Radial lines. They also have the letters JH stamped in the center of the markings, not sure if that is of any significance. Appreciate it.

Hey everybody, Thanks to this awesome site, and the great information and how to's I've found, in a few days I'll be replacing the radius arm bushings on my 92' Eddie bauer. Which is not only a huge step into the world of dyi for me but a very exiting one as well. It seems that a previous...

Awesome thanks for the info, Were you able to keep you're stock wheels?

Hi Everyone, I think I should start off by saying this is my first 4x4 vehicle, and I have very little mechanical knowledge of any sort, let alone offroad modifications.. I have a stock 1992 Explorer 4.0 4x4 five speed. I picked it up for next to nothing from the previous owner who had blown...