Search results

you can swap in virtually any seat that fits in the space if you have a drill and a tap&die set. I swapped my 94 over to bench seats in about an hour.

Just have to measure up, with a little effort you can put almost any seat in as long as the seat isn't too big for the space

Wish mine leaked heavily like that, mine leaks really slowly and makes it really hard to figure out where the leak is and I'd hate to do a bunch of work and buy gaskets for the wrong thing, just running on full water adding a gallon every saturday for a few months now lol

I just took the windows out, got all the old seal off and threw some heavy black silicone (not sure exact kind) on it, put the windows back on, never had a problem. I just didn't see much point in just sealing one leaky section, with the windows so simple to take off I don't see why anyone...

Been awhile. Finished the tailgate Stripping out even more wire After removing some windows and tailgate Made a few cuts: Other nicks: new fuel pump, finally found a fuel gauge in the right series, got that put in, finally getting rid of the original cluster hooray! Bought a rear...

Probably only 2-3k here, not much demand for 4x4s in flat Kansas

Thinking that it could fit if we move the radiator outside and cut out some of the old radiator supports

Not like this, by the time we finish, there really wont be much left. We do some pretty crazy things here, a list of current projects: 1994 Ford explorer ZAPV with n/a v8 swap 1991 Dodge Dakota turbo v8 2003 Toyota Prius with a 6.8l V10 being shoved in the rear from an E350 1998 Ricer...

Today we barbecued the fenders to medium-well, got one cut and rubbered, re-colored the headlight trim, grill, painted on some decals, grinded in some mad zombie claw effects, beat her up with some hammers a little bit, just overall got the theme on there. Kind of at a stopping point for the...

Those are some huge swampers o=

About halfway into dissecting the old cluster, now have voltmeter at 14v, oil pressure at 45 psi, and high beams light indicator. still needing check engine, check oil, battery and fuel. Btw temperature is averaging 180 with a 60 water 40 antifreeze. I might add the Speedometer actually fit...

It's way past midnight now but we have a strong start, it's only monday and most of the major wiring is cleaned up. Going from the picture above, to this: The fuse box I plan on mounting to the lower section underneath the steering wheel, I will cut out a hole for it and add an opening panel...

I said earlier I was looking into rebuilding a 4.0, but I've also wanted to consider an LS swap and 460, I've never messed with LS series before so I don't know how it would go, just going from what people say, big power for cheap. I consider the 460 because its one of my favorite motors, I have...

Update time! So here we were changing the exhaust manifold gaskets in the campus parking lot Even after continuous soaking in pb blaster over the course of 3 days and using a 3/8 drive with an extended handle turning slow as possible we still managed to break nearly every bolt. Most at the...

Pic time! First being the guages: old cluster is there until I get all the sensor wires figured out tommarow This intake became very massive very quickly, and is probably the most haggard intake I've ever put together. Originally planning to run through the fender: However the 3inch...

Back to the dash build, I just threw down about 200$ on gauges. got them all hooked up to make sure they worked first, so tommarow they are coming out, then building up the driver side portion of the dash and then putting them all back in cleanly and permanently. Also I have no bumper at the...

To take a break from doing so much upholstry, we decided to throw together that steel bumper. So heres what we got scrapped together, and now it just awaits my buddy to come down and weld it up when he has time since I'm not so great at welding and hes a professional. For now it's held in by 6...

I paid $500 for mine, had to buy some tires the others were about to pop - 200$. then had to do a FULL brake job costing about 400$, a starter for 100$, a battery for $125 terminals 5$ fog lights 40$ forced to build a new interior, was getting sick from it. from carpet to panels to headlines to...

Okay, I'm pleased to finally show some pictures of the console / part of the dash. I don't have much experience in upholstery but I don't think it turned out too bad. I might touch up some some alignment and trims but I think it came out good.

Looking nice. Suprised no one has commented. 300 for the truck and 150 for rims+ 35 tires Wow. less than 500$ for the biggest ticket items. Teach me how to find this stuff lol

If you do decide to add the boards, be sure to add some type of sealant between the board and the rockers to prevent water from reaching the rockers and rusting out. I also would build my own brackets to install them instead of using the stock design with all the pegholes.

Welp, it's been a long weekend but we managed to get the grille built and the center console mostly built. We just finished the console and it's 8:30pm so its too dark to get a picture but I'll add some tomorrow. Here's the grille at least, we decided to go against the wire because I found this...

a budget lift would probably be rough country, if you plan on having the EX for awhile I would suggest going with superlift, they are fairly reasonable and have better quality.

You would have to have the same pegholes in your rockers, or drill out your own holes, theres like 20-30 holes on each side that hold it in as well as a couple screws at the ends. I don't find much purpose for them so I would skip it really. When I bought my Eddie Bauer it had those and when I...