Search results

I imagine it was Cafe standards that moved Ford to it or perhaps it was a way to move you up trim levels, pay up for the V6 with the new model. I just checked the current Autotrader.ca ads for used Explorers from 2015 to 2019, of the 543 listed just 45 were 4 cyl, unscientific but just 8%, not...

Here some more info on the Ford 10 speed tranny and issues. It was jointly developed with GM but for some reason it is Ford who is having the problems with it. I have a 2020 Camaro (as well as my Explorer) , about 3k miles on it now, no issues with the 10 speed in it. 11 Things You Need to...

Class action lawsuits filed against the 10 speed in the F150 ... Ford F-150 10R80 Transmission Class Action Lawsuit Filed

I have a '16 XLT and have been snooping around looking for a replacement. I was very surprised that a little 4 cyl was standard on th XLT and you had to move up trims to get a V6. What idiot decided to match a 4 cyl with a full size SUV?? I may have to look at other brands.

Did they explain how the seating element corroded? Is it condensation or just a sweaty ass lol I imagine that condensation might be an issue in cold climates as they cool down. Wonder if there is any way to inspect it without tearing the seat apart?

Might be a loose wire causing the speaker to make a noise that sounds like sparking or a damaged speaker. Speakers are low voltage, not likely to be a fire issue.

After reading this I am glad I keep a log and receipts for oil and filters. Just takes a minute with each oil change to note it , the mileage , stuff the receipt in a envelope with the log, put it all in my car file. I do both my vehicles with synthetic oil , usually runs about $35-40 Cdn...

Wow, that sucks ! I had a Ford Windstar back in '99. First year they had to replace the engine, not rebuild it, replace it. Second year the tranny started slipping, I dumped it. Hate it when you run into that stuff !! I swore off Fords for some time because of that, just returned with...

Just curious how many miles on this Explorer?

Sure but look at this way, I don't need winter tires , we spend the winter in Florida :)

I've used the emerg flasher method for 3 yrs rotating my tires, turn on and off 3 times on my 2016 and it goes into training mode. Easiest way to train them. Vehicle enters train mode , then you follow the instructions on which wheel to train by letting air out. Easy peasy. I have left...

Sure could be but the Service Mgr should have told me that, didn't hear anything along those lines. What they told me is they were heating it up repeatedly over a three day period, that seems odd to me. If someone would have called me day two and said heh were trying some sprays on it...

Now I've finally got to talk to the service manager, day 4, the general manager has done what he can and got his attention. Sounds like they will write of the non-warranty costs regarding the rotors and pads. What an ordeal though, should have never come to this if they would have started...

I got a call from the Gen'l Mgr at the Ford St Petersburg Autonation dealership finally last night. Service mgr never did contact me despite my repeated voicemails asking him to call me. Gen'l mgr says it will be done tomorrow, now day 4, we'll see. The issue they say is that they can't get...

Tomorrow day four, still haven't fixed my Explorer. They tell me that they can't get the hub off just now 4 pm on day three, sure ok, three days to come to that conclusion, maybe tomorrow. Worst service I have ever had in my 45 yrs of vehicle ownership from Autonation Ford in St...

Add insult to injury. My vehicle is still sitting with with Autonation Ford in St Petes, tomorrow will be 3 days they have had it. Still no commitment on when it will be finished. Come on, I make an appt a week ahead , you diagnose it within 2 hrs and you can't fix one wheel bearing...

The left rear rotor was scarred , I noticed that right away when we got to Florida, the rear wheel was noisy as we pulled into the smooth roads of the development where we stay. So I had a good look at the brakes with a flashlight , trying to figure out if the noise was a bearing or the tires...

I used to like this vehicle , no friggin way should I be dealing with rear rotors on a vehicle that sees no winter, has annual maintenance on the rear brakes done and still needs new rear rotors and pads at 27k miles because one has gotten stuck and scarred the rotor , burned out a bearing...

Ford dealer (who is in the process of replacing my left rear wheel bearing) says I should replace the rotors and pads on the rear at the same time. I have done maintenance on these every year, lubed the slider pins, took out the pads cleaned everything and applied new lube to the slides. The...

Well to my surprise the local Ford dealer says it is a rear wheel bearing making the noise. Sure sounded like a tire to me. Just got a call from the dealer here in Florida (we are down for the winter) and he claimed they used a stethoscope to be sure and it is the left side rear. I had...

I rotated my tires in Sept again, the vehicle never re-learned. After a week or more I went out and did the routine of pressing the 4 way flasher button on and off 3 times to get to re-learn mode and then let air out out of each tire as instructed by the system. Worked then , not sure if...

Thanks Stephen , never considered Bridgestone before, I will take a look at them. Others have recommended the Defenders.

I have Michelins on my C7 'Vette, stick to the road like glue, good tires, although admittedly I only drive it in the summer on nice days - not a real test of tire quality. I'm a little disappointed in the Explorer's but fact is I do have 26k miles on them, I might be able to squeeze 35k...

Nope. Bumper to bumper was done in September so I doubt they would fix under the TSB without paying up. I can live without this feature, as long as the FOB and buttons work no need for a foot activated feature that worked only when it wanted to. This wasn't as much of an issue a year ago...

Just finished pulling the plug on this problem. Simple solution removing the sensor plug in at the bumper. I covered both ends well with electrical tape to seal them off, will check in month or so see how that his holding in.