Dismiss Notice

and gain access to Reviews and Discussion of the 2016 and 2017 Ford Explorer Tech Tips, How to Articles, Off-Road Modifications and Events, Street Truck Mods and Events, and much more! Since 1996 our community has covered every aspect of the Ford Explorer, Ford Ranger and all vehicles based on this platform.

Register Today It's free! This box will disappear once registered!

Ford Explorer P1464 Error code

Discussion in 'EEC V' started by Majik69, January 11, 2007.

  • Searches ExplorerForum.com
    1. Majik69

      Majik69 New Member

      Joined:
      January 11, 2007
      Messages:
      1
      Likes Received:
      0
      Trophy Points:
      0
      City, State:
      El Paso TX
      Year and Model:
      2002
      My 2002 ford explorer into have it inspected. The mechanic came to me and told me it failed due to an emission sensor being bad. Shows me the print out with the fault code emmision sensor. I had him replace it. Then he tells me I have to drive the truck around to get it through a "drive cycle". While driving it the check engine light comes on. I take it back and now he is telling me it has a different fault code P1464 ACCS to PCM high demand during self test.A/C. Says he cant pass the truck until this fault is cleared up. Did i mention he does A/C repair also ? Anyone got any suggestions on this? ::salute:
       
    2. Support EF


      Join the Elite Explorers for $20 a year

      Explorer Forum has probably saved you that much already, and will continue to save you money as you learn how to diagnose and fix problems yourself, and learn which modifications work without having to experiment on your own. Elite Explorer members see practically no ads, add your own profile photo, upload photo attachments directly to your posts and Media Gallery, create more private Conversations, and more. Join Today. Your support is greatly appreciated.



      to hide adverts.
    3. ExplorerDMB

      ExplorerDMB Moderator/Technician Moderator Emeritus

      Joined:
      January 26, 2004
      Messages:
      6,209
      Likes Received:
      0
      Trophy Points:
      0
      City, State:
      Mechanicsville, Virginia
      Year and Model:
      2004 Acura TL
      He needs to make sure he doesn't have the ac/heat on - the switch needs to be on off:

      1. Rerun the Key On Engine Off (KOEO) or Key On Engine Running (KOER) test with the heater/A/C controls turned OFF. If the code doesn't come back, there are no problems.

      2. If the code is still present, check pin #41 Dark Green/Orange (DG/O) wire at the Powertrain Control Module (PCM) for voltage with the controls still set to OFF. There should be no voltage present. If there is, disconnect the low pressure cycling switch and recheck. If the voltage is still present, locate and repair the short to power between the low pressure cycling switch and the PCM.

      3. If the voltage on pin 41 goes away with the low pressure cycling switch disconnected, check for a shorted control switch on the dash, or a short to power between the control switch and the low pressure cycling switch.

      -Drew

      That code doesn't set the CEL - it only comes up during the Self Test! Theres another code in the system if your CEL came on!
       
    4. NeroRising

      NeroRising New Member

      Joined:
      April 9, 2011
      Messages:
      2
      Likes Received:
      0
      Trophy Points:
      0
      City, State:
      Quincy, IL
      Year and Model:
      2004 Ford Exploder XLT 4L
      Thank you for this info...I'm an idiot..but thank you for this info. I just did the KOEO, KOER tests and about freaked out when this code as well as the P1000 code came up.
       

    Share This Page


    Click Here

    We Support Our Troops!