Search results

I replaced the front differential seal for the right axle the other day, after realizing fluid loss and virbrations from front end when driving on the highway. I began getting those vibrations again and notice that fluid was dripping from the new seal but where the right cv joint goes into...

Has anyone personally installed the FMS headers? If so, did you follow the instructions to the T? if not what parts did you skip and how easy or hard was it to install? P.s., I just got mine today from for 179.. part # FMS- M-9430-E50

Hi all, I am proud to say that I am an ELITE EXPLORER!!! :)

Before After I'm not done yet :) [Edited by EMStaxi on 02-12-2001 at 02:20 PM]

I have done the torsion bar twist and haven't gone to get the alignment yet. I get vibrationfrom the front end at higher speeds(85-90 mph). It was worse till I readjusted the bars. It seemed like with the highway dips and the height of the bars caused the cv joints to hit the maximum angles...

For those of you with BFG 31x10.5x15's, what tire pressure are you maintaining? Max tire pressure is 50psi. I have kept mine at 32-35psi, but was thinking about going up to 40. Any suggestions? Anyone find out what the manufacturer recommends? I bought the tires at a used tire shop so they...

This is my before....hope this works...

I found this website through a magazine. They have the Altezza style tail lamps alot cheaper...http://www.nopionline.com/partdetails.asp?ProductID=158482. If anyone orders them, let me know since I don't have the money yet. I'm recovering from "xmas".

Ok here's the deal, I figured out that I have a 19 tooth gear and I need a 17 tooth gear. Here is the question, my original is pink but according to this chart I found or The Ranger Station.Com shows this...(I have the Auto Tranny) Manual Transmissions: 16-teeth-wine(C0DZ-A)...

Does anyone else have that annoying Alternator whine that increases when you step on the gas and decreases when you let up? I have heard the sound on other explorers that have passed by me while I would be standing outside, so I know its noticable. Not having any problems with the charging...

I have a question about headers for the V8. Could I use headers made for the 90's and up stang on my truck? If so, what type of headers (i.e. shorty, 4 into 3 etc). I really don't want to pay the price that Explorer Express is asking if I don't have to. Thanks

I would like to new if anyone has tried the new Z MAX car treatment that is advertised on tv and sold at PEPboys. What are your impressions?

John, where did you get the headers from? What brand? How much? Did you install them your self or did you have it done? ------------------ Norman B. 97 Mountaineer 5.0 V8 AWD KKM Tru-Rev with Homemade Ram Air BOSCH PLATINUM +4's Prestige Platinum 750a-APS alarm w/ remote start Edelbrock...

I left my job, took off up the road... no probs. As I passed a car, I started to hear a rattling noise (figured it was the other c ar since my window was down. Anyway as I slowed down to turn a corner, I felt the rpms go down and then the truck stalled. I threw it into neutral, started it up...

I've seen ads about Throttle Bodys spacers igve an extra 5-7 Hp. What is the purpose of the spacer in relation to Hp? ------------------ Norman B. 97 Mountaineer 5.0 V8 AWD KKM Tru-Rev with Homemade Ram Air BOSCH PLATINUM +4's Prestige Platinum 750a-APS alarm w/ remote start Edelbrock...

I am trying to locate the PCV valve on my "taineer" but can't seem to find it. I've read the Haynes manual and it says that on the V8's it's located behind the intake manifold. Has anyone esle been able to change theirs w/o a problem? ------------------ Norman B. 97 Mountaineer 5.0 V8 AWD...

I just purchased and installed my set of Performer IAS'...The ride on the highway is excellent. On city streets are you supposed to feel the bumps alot less? For me, It seems like wheels take the brunt of the bumps and all I hear is the noise. Comments Please. Also I tested my truck off road...

Have you made any mods to your air box? I know that when i did to mine, It sounds louder, and the MAF makes a hissing sound due to the increased air flow. I think that "bogging" sound you hear is normal. I just cleaned my MAF the other day and it sounds slightly louder than before. I also...

Hey George, I too have a 97 Mountaineer and wish to do some of the mods you have mentioned. I have bee searching for headers and the only company that I think will have them is STEEDA...www.Steeda.com. I havent been able to find out how much they are or where to order them yet. If you don't...

Has any one with an Explorer/Mountaineer V8 changed stock wires to performance wires? What brand will fit the DIS pack? ------------------ Norman B. 97 Mountaineer 5.0 V8 K&N Airfilter-Modified Airbox with homemade Ram Air BOSCH PLATINUM +4's More to Come Before Summer :)

I recently purchased my fist SUV so i'm new to these types of suspensions... While checking out the rear shocks (planning to put on Edelbrocks) I noticed a third shock connected between the right lower side of the axle and the frame. What is the purpose of this shock? can it be replaced with a...

Question...Has anyone with an AWD Explorer or Mountaineer been able to have their truck put on a Dyno machine to have it tested? If these Dyno shops can accomodate AWD, does anyone know of any in the New Jersey New York area? ------------------ Norman B. 97 Mountaineer 5.0 V8 K&N...

I have taken out the lower half of my air box and just have the K&N filter connected for the time being; What type of gas does everyone use? I was using 87 ever since changed the filter, but decided today to try 91. No one from what I have read has said what they use so I figured I would...

I have been reading these posts for a while and I think I want to go with the Borla Catback Exhaust system. Has any one installed the system theirselves, and if so how difficult is it to do? Also i'm trying to find the best price off the internet. Any suggestions? ------------------ Norman...