Search results

Do a simple check. Mike, I have had problems with amps doing that as well, most of the time you can track it down to a fuse having a little bit of corrosion on it. Check all of you fuses and make sure they all look good. If the problem continues to occur, I have a Hifonics Zeus...

will fab-techs ranger A arms fit the explorer sport.

Thats what I thought, I thought I would swap it for a C6

He guys you probably know me from the 2nd Gen Explorers but I found something to get me into the first gen too. A long lost buddy of mine has a 91 Ford Explorer XLT with the AL4D Tranny in it, an 87 H.O 302 swapped into it, Full racing exhaust (Headers, Flows 40, and 2 1/2 inch pipe, true duals...

Thanks Jefe I was thinking the same thing but wanted somebody else to say it too.

I put 38.5 Boggers on my 98 Explorer Sport 2wd and it sucks gas and is extremely underpowered. It has the 4.0L OHV motor and is the 5 speed auto. What gears should I get 4.88's or 5.13's. Thanks Pat

isnt this a common mod?

anyone, i think i have the answers buit need a second opinnion.

Hey guys, I blew up my carrier in my ford 8.8, the limited slip crapped out and know is clunking. I want to put an open carrier from a first gen in it and then spool it or lock it. Will a first gen carrier fit in a second gen 8.8? And if not, can you swap disk brakes on the 1st gen axle?

Does anyone know if this would work?

Hey guys, I have been thinking, recently (while wheeling) I got about 4 feet of air and destroyed my front end on my 2wd. Torsion bar were bent as well as my lift spindles. Well since the Torsion Bars are no good, and i replaced the spindels, I was wondering if i got the RCD Lift kit brackets...

I have a 98 Explorer and i have had it lifted for sometime now and I am thinking about a make over and slamming it to the ground. I am just curious if anyone wants to buy the lift parts from it (the only way im putting it on the floor is if people want to buy the parts). Well heres what I got...

I am 2wd, 3 inch lift spindles, 3 inches of TT, and a 3 inch body lift, Soa. I have eough to fit 37's and maybe 38's but i have a 15x10 inch rim with a 4.0 backspace and -39 mm of offset. I like the wide stance so will the 17 with 4.5 backspace and 0 offset willstick out like my others?

.....

Has anyone ever ran, 35x12.50x17 inch tires on 17 with 4.5 backspace on there truck and if you have, do you have any pictures? I have a set of BFG 35x12.50x17 sitting around and stealies are cheap.

I am going to do a Solid axel swap on my 2wd and then convert it 4 wd afterwards, what should i use on the front? D30 or D44, it will be fitting at least 37's most likely bigger. Thanks in advance.

I want to use a trailmaster kit with my 3 inch lift spindles on my 2wd. Has anyone attempted or has done it? If so tell me what you did and what parts you needed. It will help me out greatly. Thanks, Pat

Hey guys i want your opinnion about what ratio gears i should put in my truck. Its auto and has 33's but hopefully 36 or 37's going on real soon. What gears should i get ratio wise?

Ive heard that you can only run a certain type of lunch box lockers on a limited slip. What are some of the product that you guys have been using? What is the benifit of having the locker on a limited slip? Brand and model of locker would be appreciated. Thanks

Its got a 5.0 with an AOD in it

Ok, a buddy of mine has a 1st Geneation explorer that originally had a 4.0L in it, which he swaped to a Carb 302 which bolted up to the stock tranny which is a 4 speed auto. I want to buy the truck off him and put the motor and tranny into my second generation sport. Is this humanly and...

Only $45.92 each from Ford, Not after market sensors made

They dont, i could not get mine out so, I dont have front ABS. Try sooking it in Liquid Wrench or PB Blaster (my favorite) and proceed with a screwdriver.

Sorry to say this, but what do you guys do, I run a shop all day long and then work on our trucks (4 Wheel Adiction's) for shows until the wee hours in the morning. It takes 2 minutes max to climb under your truck and measure a driveshaft, thanks for all the reply's that I got (0). I dont know...

Hey guy, can someone do me a big favor, anyone with a foor door, 2wd xlt ranging from 95 to 00, measure your driveshaft from weld to weld, right before your U Joints. Youll see the weld, it is a big indentation right before each U Joint. Please help me out, Somebody just get out there and...