Search results

:biggthump Thanks again guys I found the problem. It was a plug wire that was burnt in half. Never thought to look for it sense I had just replaced them not to long ago.:roll:

thanks guys.I'll try both ideas and see where it lands me.

My 94 X recently started spuddering. It does this whether it's at an idle or WOT. Does seem to get worse when it shifts in to OD. I just replaced the IAC sensor. And that didn't help. I don't wanna keep spending money for parts I don't need. Any & all help would be greatly appreciated.

Well I'm happy to report that the Little Green Monster is running awesome:burnout:.Everything is back to normal. Thanks for all the help everyone.:biggthump

Sorry they are blurry I used my camera phone & i don't have a steady hand. Oh & to answer you ? About what dry gas is. It is an additive to take care of water or condensation in your fuel service.

Hey Corkey. No the check engine light wasn't on.All the relays & the fuel pump kick on. I changed the plugs & wires this morning(what a chore it was doing the pass. side).Check Engine light came on after I changed plugs & wires. So i reset the computer. The light went out but it is still idleing...

What is a fpr? There are no codes that i know of. I have not put a code scanner on it. I just bought it a few months ago,& haven't had the chance to give it a proper tune up.

:dunno:Not sure where to post this so plz forgive me. Ok here is my problem.About a week ago i tried to start my X and it would only crank over.It ran perfectly fine the day before. I went out in the morning & it would only crank over.After trying for sometime i decided to wait awhile,when i...

UH no it's better than an el camino,it's a RANCHERO

they work really good so far

no no no the driving lights replaced the stock driving lights. i added the kc & put them on a relay

kc i used a relay 4,but replaced the stock driving lights w/the fog/driving lights

Well i'm not to good at writing all that tech stuff like most ppl on here. But I used a 30amp relay & a 30amp fuse before the relay.As far as the wire gauge I used the same size that came on the lights, what ever size that maybe not to sure. (LOL) I used a piece of 1/8 inch plate steel That...

thanks little x. & thanks for bring my typo to my attn: they are driving lights

Well i finally got to drive the X at night (4am) a few times on my way to work & the lights worked gr8. I even spotted a few dears that i probably never would have seen.

Hey Gln the dimensions are 9x5

I just finished it tonight. Probably didn't need that many bolts but better safe than sorry. I'll have to measure it again in the morning & let ya know I don't remember off hand what the dimensions are. I think it'll hold up just fine till i can come across a bull bar & different bumper for it.

How'd ya guess lol

Thanks. I plan on getting the name printed out. I know the guy thats does 90% of the sprint car decals where I'm at.

Sounds like the dealership doesn't know their buts from a hole in the ground. I bet if you took it some where else you wouldn't have so many problems. The badge on the front is the best part of the truck. IMHO Nice ride tho :biggthump

I Fabed up my own bumper bracket & mounted them direct to the bumper.I hooked the KC day lighters up to my high beams via relay. Installed new driving lights from wally-world.Even thought of a name for the old girl LIL GREEN MONSTER. BEFORE I GOT STARTED AFTER NEW DRIVING LIGHTS FAB...

Thanks bill.:thumbsup: I drive down a couple of dark roads,& they are known for having alot of deer around. plus they'll help out when i get a fire call & need the extra light out in the middle of some field.:D

I have a pre-wired harness for my lights. My question is can i hook the wire that would normally run from the aux switch to the relay,could i hook that into 1 of my high beam wires so that my KC's would come on at the same time my high beams do? I just removed my stock driving lights &...

Welcome To Forum!:wavey: