Serious Explorations Ford Explorer and Ranger Message Board
#1 Resource for Ford Explorer and Ranger Owners - By Enthusiasts, for Enthusiasts.


Ford Explorer Generation Guide

EF Swag Store 2015 Ford Explorer Forums Elite Membership Chat Room My Posts Reviews Explorer Photo Gallery
Go Back   Ford Explorer and Ranger Forums "Serious Explorations" > Classifieds: Explorer / Ranger / Bronco II Parts For Sale and Wanted > Explorerforum Vendors

Notices

Explorerforum Vendors These folks are helping to support the site. If you are a vendor and would like to be able to sell products on the site, please contact me to make arrangements. Email - ab7fh@yahoo.com

1st Gen Explorer Winch Bumpers ON SALE

Reply
 
Thread Tools
Old 06-06-2011, 10:20 AM   #61
DV8
Cedar Grove, WV
94 XLT
 
Join Date: Jan 2011
Posts: 72

Vehicle Specs

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
how much for a set of your bumper brackets, and do you have a pic of them? i torqued my rear bumper pretty good pull starting a buddy's ford diesel, and destroyed what rust was holding the brackets together.




__________________
94 XLT 260,000 4.0L auto, with original engine and trans. MODS: Mile Marker manual hubs. ACCESSORIES: custom interior green dome lights, air freshener, two car seats.
95 Nissan Altima GXE 250,000 2.4L 5spd with original engine and 2nd trans. All stock, runs with a 2003 rustang gt

a big enough hammer fixes anything
DV8 is offline   Reply With Quote
Old 06-09-2011, 05:55 AM   #62
jamscal
EF Vendor
Louisville, KY
1999 car car
 
Join Date: Jul 2009
Posts: 120

Vehicle Specs

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
(Original Poster)
Quote:
Originally Posted by DV8 View Post
how much for a set of your bumper brackets, and do you have a pic of them? i torqued my rear bumper pretty good pull starting a buddy's ford diesel, and destroyed what rust was holding the brackets together.
Don't have a pic. They are just 1/4" plate with three holes popped in them, in the basic shape of the side profile of the bumper. (I'm thinking they are about a 6x12" rectangle, with one of the corners cut off at about a 45* angle)

I could probably do them for $40 shipped, and if you wanted them longer so you could build your bumper your way I could do that too.

Thanks,

James




__________________
RLC Welding and Fabrication

Custom Explorer and Ranger Winch Bumpers

(502)403-6832
jamscal is offline   Reply With Quote
Old 06-21-2011, 08:05 PM   #63
easymc
Elite Explorer
Hamilton Tx
 
easymc's Avatar
94 2dr sport
 
Join Date: Apr 2011
Posts: 189

Vehicle Specs

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
James ,the bumper for my 86 Bronco came out great, mounting brackets were right on .






__________________
Long live the 2nd Admendent. Life member NRA

94 EB 2d
http://www.explorerforum.com/forums/...d.php?t=333138
easymc is offline   Reply With Quote
Old 06-21-2011, 09:27 PM   #64
jamscal
EF Vendor
Louisville, KY
1999 car car
 
Join Date: Jul 2009
Posts: 120

Vehicle Specs

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
(Original Poster)
Thanks for posting the pics!




__________________
RLC Welding and Fabrication

Custom Explorer and Ranger Winch Bumpers

(502)403-6832
jamscal is offline   Reply With Quote
Old 07-06-2011, 11:55 AM   #65
Spicycook
Kennesaw ga
1994 limited
 
Join Date: Jun 2011
Posts: 88

Vehicle Specs

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Pm sent.




__________________
94 limited
Spicycook is offline   Reply With Quote
Old 07-22-2011, 09:33 AM   #66
jrsbuck25
Shamong, New Jersey
1993 explorer
 
Join Date: Jul 2011
Posts: 21

Vehicle Specs

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
How much for the one in the very first pic?
jrsbuck25 is offline   Reply With Quote
( Join the Elite Explorers )

For only $20 per year you can become an Elite Explorer member. Explorer Forum has probably saved you that much already, and will continue to save you money as you learn how to diagnose and fix problems yourself, and learn which modifications really work without having to experiment on your own. Elite Explorer members can change the forum "styles" to eliminate most ads, including blue underlined links, and no ads on photos. Other benefits include the ability to store 1000 Private Messages, upload photo attachments directly to your posts and to our Photo Gallery and more. Join the Elite Explorers today.


Old 07-23-2011, 07:49 AM   #67
jamscal
EF Vendor
Louisville, KY
1999 car car
 
Join Date: Jul 2009
Posts: 120

Vehicle Specs

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
(Original Poster)
Quote:
Originally Posted by jrsbuck25 View Post
How much for the one in the very first pic?

$399 shipped for the bumper, plus $50 for the hoop shipped/included but unwelded.

Thanks,

James




__________________
RLC Welding and Fabrication

Custom Explorer and Ranger Winch Bumpers

(502)403-6832
jamscal is offline   Reply With Quote
Old 07-29-2011, 01:13 AM   #68
Steeda04SVT
Elite Explorer
Kansas City, MO
 
Steeda04SVT's Avatar
1997 Eddie Bauer Explorer
 
Join Date: Mar 2011
Posts: 502

Vehicle Specs

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 21 Post(s)
Do you have any picture of the light tabs you weld on and plus how backed up are you right now? Def plan on getting one for my 90 B2. Do you have a pic that has been used on a B2?




__________________
Former USAF AC-130H Spectre Gunship Crew Chief ('02-'12)
BNSF Railway
2004 Terminator Cobra - Sold
97 XLT Explorer 5.0 - Project Car
~Rancho 5000 Shocks - Shackles - 2" TT Coming soon!!

Last edited by Steeda04SVT; 07-29-2011 at 01:26 AM.
Steeda04SVT is offline   Reply With Quote
Old 07-29-2011, 04:40 PM   #69
jamscal
EF Vendor
Louisville, KY
1999 car car
 
Join Date: Jul 2009
Posts: 120

Vehicle Specs

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
(Original Poster)
Quote:
Originally Posted by Steeda04SVT View Post
Do you have any picture of the light tabs you weld on and plus how backed up are you right now? Def plan on getting one for my 90 B2. Do you have a pic that has been used on a B2?
I can do any sort of light tabs you'd like...today they were about 2"x1.5" with a 7/16 hole.

No pics on a BII.

I'm quoting 2 weeks right now on delivery, but getting busier.

Let me know if you have any other questions.

Thanks,

James




__________________
RLC Welding and Fabrication

Custom Explorer and Ranger Winch Bumpers

(502)403-6832
jamscal is offline   Reply With Quote
Old 08-26-2011, 11:11 AM   #70
Backwoods "X"
Mt. Sterling, Ky
94 XLT
 
Join Date: Jun 2011
Posts: 223

Vehicle Specs

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Any objections to a local pickup? My wife is from down in Radcliff, and it is almost time to go see the MIL (again). It would give me a GREAT reason to ditch the MIL for a while, AND, meet a fellow boardmember.
Backwoods "X" is offline   Reply With Quote
Old 08-26-2011, 04:19 PM   #71
jamscal
EF Vendor
Louisville, KY
1999 car car
 
Join Date: Jul 2009
Posts: 120

Vehicle Specs

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
(Original Poster)
Quote:
Originally Posted by Backwoods "X" View Post
Any objections to a local pickup? My wife is from down in Radcliff, and it is almost time to go see the MIL (again). It would give me a GREAT reason to ditch the MIL for a while, AND, meet a fellow boardmember.
Local pickup is fine. Shop is open m-f 8-5 but I can meet you at other times/on the weekend if my wife doesn't have anything else planned for me.

Thanks,

James




__________________
RLC Welding and Fabrication

Custom Explorer and Ranger Winch Bumpers

(502)403-6832
jamscal is offline   Reply With Quote
Old 09-15-2011, 12:48 AM   #72
SSETHRADRA
Sun Prairie, WI
1996 Ford Ranger
 
Join Date: Sep 2011
Posts: 1

Vehicle Specs

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Hey man, Awesome work on the Deer killers! I was wondering what the one you had on the white Mazda would cost for a 1996 ford ranger stock hight, to 53590.
Thanks!
Zed
SSETHRADRA is offline   Reply With Quote
Old 10-12-2011, 07:41 PM   #73
93 Xploder
dkbmx123@gmail.com
dkbmx123@gmail.com
 
Join Date: Aug 2011
Posts: 14

Vehicle Specs

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Still making these? Whats turn around time right now? And light tabs are free correct?

Drop me a pm to keep clutter down.
93 Xploder is offline   Reply With Quote
Old 11-29-2011, 08:42 PM   #74
jamscal
EF Vendor
Louisville, KY
1999 car car
 
Join Date: Jul 2009
Posts: 120

Vehicle Specs

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
(Original Poster)
This one is going to be a bit different, sort of a hybrid style:

First Gen.





Thanks for looking.




__________________
RLC Welding and Fabrication

Custom Explorer and Ranger Winch Bumpers

(502)403-6832
jamscal is offline   Reply With Quote
Old 11-29-2011, 09:16 PM   #75
Patened
prdebevec@gmail.com
91 XLT
 
Join Date: Apr 2011
Posts: 33

Vehicle Specs

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
thats awesome!!

It that my bumber james looks like it. Cant wait to see how it looks when your done. What else do you have planned for it and whatnot.
Are where we planned to put the lights going to be tapped or will i be needed to do that?
Patened is offline   Reply With Quote
Old 11-29-2011, 09:50 PM   #76
jamscal
EF Vendor
Louisville, KY
1999 car car
 
Join Date: Jul 2009
Posts: 120

Vehicle Specs

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
(Original Poster)
Quote:
Originally Posted by Patened View Post
It that my bumber james looks like it. Cant wait to see how it looks when your done. What else do you have planned for it and whatnot.
Are where we planned to put the lights going to be tapped or will i be needed to do that?
Yes, it's yours.

I'm going to put some tabs down there on the bars, and cut the yellow circles out to clear the lights.

I'll pm you on some other details.

Glad you like it...I think it's pretty cool too and want to see some installed pics.

Thanks,

James




__________________
RLC Welding and Fabrication

Custom Explorer and Ranger Winch Bumpers

(502)403-6832
jamscal is offline   Reply With Quote
Old 03-28-2012, 08:36 PM   #77
gizmo
Cary,NC
91 xlt
 
Join Date: Feb 2011
Posts: 4

Vehicle Specs

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Whats the biggest winch it can hold?
gizmo is offline   Reply With Quote
Old 03-29-2012, 05:21 AM   #78
jamscal
EF Vendor
Louisville, KY
1999 car car
 
Join Date: Jul 2009
Posts: 120

Vehicle Specs

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
(Original Poster)
winch mounting area is approx 32x7, and the bolt pattern is the common 4.5x10.

A 12,000 will physically fit, maybe larger depending on the brand.

-James




__________________
RLC Welding and Fabrication

Custom Explorer and Ranger Winch Bumpers

(502)403-6832
jamscal is offline   Reply With Quote
Old 04-27-2012, 08:49 PM   #79
GAexplodr223
norcross, ga
92 xlt
 
Join Date: Oct 2011
Posts: 18

Vehicle Specs

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
hey

I was wondering if these bumpers are still available for purchase also do you make a rear bumper. thank you
GAexplodr223 is offline   Reply With Quote
Old 05-02-2012, 08:54 PM   #80
jamscal
EF Vendor
Louisville, KY
1999 car car
 
Join Date: Jul 2009
Posts: 120

Vehicle Specs

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
(Original Poster)
Quote:
Originally Posted by GAexplodr223 View Post
hey

I was wondering if these bumpers are still available for purchase also do you make a rear bumper. thank you
Yes and yes. Rear bumpers ore in this forum or pm me and I'll find the correct links.

Thanks,

James




__________________
RLC Welding and Fabrication

Custom Explorer and Ranger Winch Bumpers

(502)403-6832
jamscal is offline   Reply With Quote
Reply



Suggest this thread to friends:



Join the "Elite Explorers" Today!



Search Explorer Forum


Top of Page

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:43 AM.



US Flag
We Support Our Troops!

Explore the site!


Copyright 2014 - 1996 Rick Horwitz Photography



Ford Motor Company is not involved in the management of this site in any way.



All tips on this site are for use at your own risk and discretion.

Modifying the suspension on any vehicle will cause changes to its handling characteristics.



Vendor Tools vBulletin Plugins by Drive Thru Online, Inc.