Search results

Alright guys doing my oil pan gasket on my AWD EB I got everything unhooked that needs to be, I got a engine support bar to hold the engine when I jack it up. I was just wondering where do I hook the chains to? There obviously aint no hooks for this so where is the engine usually supported at?

Well your bad mileage could be based on the factory your not running the right tire pressure. 30psi is the correct pressure on our vehicles. Also have you had a tune up done recently? Plugs? Wires? Fuel Filter? All fluids maintained? Cleaned the maf and throttle body? Is it AWD? Got remember...

Started on it today so far process isn't bad I've got everything unhooked in the front end except the drivers side knuckle and half shaft and the front drive shaft only took a couple hours.

Alright guys my truck has finally got the dreaded oil pan leaking, and yes it's AWD. I have read all the threads on replacing it. I Know it can be done in the truck or by pulling the engine. I'm just thinking of a plausible way to attack this thing. I know a engine hoist will be needed to lift...

chef duane if shes gonna junk it i will take it if you can get it from her im in the DFW area and own a 5.0 already and she has been a great and reliable vehicle id hate to see these vehicles go the way of the dinosaur because they are older and having issues but yet are built so well and...

31s fit fine on a stock explorer no rubbing

yea i got frustrated with it and walked away so I dont break anything gonna go back out tomorrow and see if i can get it to seat like it should i thought about removing the dowels and tacking the gasket into place instead of them holding it on i was thinking as well the pan was preventing it...

Yea my TC is refusing to line up on both dowels on the block at the same time the old one came off fine with the oil pan there so I dont know if its the old gasket or new seal on bottom of the cover binding it up. The crank bolt on the truck isnt bad if you got a good 1/2 impact and a good...

bobflood I live in the south so Im gonna hit a yard up for the studs that broke off that way I have oem still. delexploder if those studs are as rusted as mine were be prepared to destroy the TC to get it off and have to replace it Im in the process of re assembly currently.

Believe it or not I havent been flashed since installing them they dont really glare being as the housings are smoked I think it helps in reducing that part of it.

Hey Guys had to replace my water pump and without a hitch the two bolts on opposite sides the pump broke, got the cover off and remaining parts out the block. I know ford has discontinued these bolts, what have you guy used as replacements and what thread pitch are the originals? Second whats...

i went with these housings and some hids in both headlights and foglights on my 98 https://www.dropbox.com/s/ofuvt2dqkjkcrh8/truck.jpg?dl=0 https://www.dropbox.com/s/ikqr4llz1rs4kqh/hid%20fogs.jpg?dl=0

My 98 Eddie https://www.dropbox.com/s/ikqr4llz1rs4kqh/hid%20fogs.jpg?dl=0

i got a new power mast at antennamastsrus.com for like 20 bucks

i wouldn't mind having those window visors to put on my 98 if your willing to part with them. Im located in Texas as well

your owners manual should give the locations of all the fuse and relays both under the hood and in the cabin

I wouldn't think it would like i said every 5.0 I've seen underneath has the exact same leak in the spot and its the determination its the rear main seal, ford released a updated kit with a sleeve to address this issue. Remember that seal is blocked by the flex plate and torque converter so it...

Unless they changed tire size from 98 to 99 stock should be 255 70 16 on a second gen explorer and being the mounty is a explorer of the same year just rebadged that should be your stock tire size

Its the rear main seal they are notorious for leaking on the 5.0's mine is doing the same, was diagnosed years ago by a shop, im running a thick viscosity oil and it seems to have stopped the leak

98 has the FPR on the tank I replaced mine a few years ago when my pump went

have you tried rockauto.com?

http://www.modifiedlife.com/1999-ford-explorer-car-light-bulb-size-guide/

Here's mine on my 98 Eddie https://www.dropbox.com/s/x922d588p7aa8s2/10818360_715543211894848_6555840463008401252_o.jpg?dl=0

got a brand new one for my 98 here rather cheap to http://www.antennamastsrus.com/

Rims should fit as long as same bolt pattern which 5x4.5. Wiper I would check the motor out to see if its good or not. they are common on explorers. Fuel gauge problem could be a bad sending unit in the tank. Manifold gaskets are possible with right tools a bit of patience. I just had mine...