Dismiss Notice



Register Today It's free! This box will disappear once registered!

Gman's Adventure trailer build thread.

Discussion in 'RV / Trailers / Camping' started by gmanpaint, May 15, 2018.

  • Searches ExplorerForum.com
    1. gmanpaint

      gmanpaint Back in 5 minutes Staff Member Moderator Elite Explorer

      Joined:
      August 1, 2008
      Messages:
      9,722
      Likes Received:
      673
      Trophy Points:
      133
      City, State:
      STL MO
      Year, Model & Trim Level:
      Modified 95 XLT
      I will use the silicone for the leveling jacks, as I already have a can of the CRC brand. Overspray isn't a concern with these. That 15 min wait tip is a good one! Thanks for those tips guys. :)

      I am still going to try the PTFE stuff on the roof top jack tho. No mess, and been meaning to get it for the rigs Uni-Balls anyways.


      More rambling thoughts...........

      Speaking of flip flop, I have changed my mind (again) on the interior set up. Fridge is going in the front compartment, and sliding out the Dr side. The water holding tank is going on the front pass side, as the instant hot water heater will be on that side, and makes it convenient for water fill/vent/electrical hookups to the front of the cabin wall. The molded water tank can be strapped to the framing well in this location, and will have ample room for the pump as well.

      This leaves the rear fairly open for the Kitchen pull out, and the other half open for storage of large camp gear. Considering making a box 3'H x 1.5'Wx4'D, and with 3 shelves to store things neatly, and easier access. I'm hoping the kitchen and items stored help put some weight on the axle, and take some off the tongue from fridge and water tank. The T-box and spare are around 350 lbs right now, and the fridge and tank will add another 400 lbs give or take.

      Thinking the water system needs to be built next.
       
    2. Support EF

      Join the Elite Explorers for $20

      Explorer Forum has probably saved you that much already, and will continue to save you money as you learn how to diagnose fix problems yourself and learn which modifications work without having to experiment on your own. Elite Explorer members see practically no ads, can add their own profile photo, upload photo attachments in all forums, and Media Gallery, create more private Conversations, and more. Join Today. Your support is greatly appreciated.


      to hide adverts.
    3. gmanpaint

      gmanpaint Back in 5 minutes Staff Member Moderator Elite Explorer

      Joined:
      August 1, 2008
      Messages:
      9,722
      Likes Received:
      673
      Trophy Points:
      133
      City, State:
      STL MO
      Year, Model & Trim Level:
      Modified 95 XLT
      mystery parts.jpg
      hinge side.jpg
      partially open.jpg
      Closed.jpg
      primed 1.jpg
      backside finished.jpg
      front finished.jpg
      3 ft 7 pin extension.jpg
      box open cables connected.jpg
      all together top.jpg


      Square security Cog for Da Machine!

      When unhitched, the 3 ft extension gets removed, and stored in the tow pig, and the box gets locked.

      The tab on lock side, stops the lid from lifting, if someone goes thru the trouble of unscrewing the hinge. Have to break or cut the lock off. With the lock in the middle, a cut off wheel would be needed
      Just another thing to slow them down, and make them work for it. The way I see it, the more deterrent there is, the more of a chance, it doesn't get stolen.

      There are more things like this being done, but won't be shared, for obvious reasons.
       
      Last edited: January 8, 2019
    4. gmanpaint

      gmanpaint Back in 5 minutes Staff Member Moderator Elite Explorer

      Joined:
      August 1, 2008
      Messages:
      9,722
      Likes Received:
      673
      Trophy Points:
      133
      City, State:
      STL MO
      Year, Model & Trim Level:
      Modified 95 XLT
      Took a couple tries, and what seems like months, but the Tongue box lid gas props are on and working.

      First set were too long to work, and wouldn't let the lid close all the way. After failing the first go around, I figured out what size to order. Some of this stuff, is either getting harder for me to figure out, or it really is just a PITA sometimes. lol

      Lid stops at 90* upright, and is exactly what I wanted.

      They even have the Made in USA stamps on them. :D

      tbox prop pass side.jpg t box prop dr side.jpg


      If Apple made an Off road trailer....... Would it have Windows?
       
    5. gmanpaint

      gmanpaint Back in 5 minutes Staff Member Moderator Elite Explorer

      Joined:
      August 1, 2008
      Messages:
      9,722
      Likes Received:
      673
      Trophy Points:
      133
      City, State:
      STL MO
      Year, Model & Trim Level:
      Modified 95 XLT
      No weekend updates. Broke a couple back teeth in half on Christmas dinner. Trying to get them taken care of this time of year is about impossible. Was up for 3 days, as raw nerves like constant attention, and do not like to sleep.

      Hoping to have mah face back in working order soon, and resume work on this beast.

      Happy New Years EF!!
       
    6. toypaseo

      toypaseo Flunked daycare Elite Explorer

      Joined:
      January 3, 2003
      Messages:
      6,602
      Media:
      28
      Albums:
      1
      Likes Received:
      248
      Trophy Points:
      83
      City, State:
      outside shovelling snow
      Year, Model & Trim Level:
      ................ 96 XLT ™
      On the "Square security Cog", any possible issues with those hinge screws rubbing through anything inside, or wires rubbing on the openings on both ends :dunno:
       
    7. gmanpaint

      gmanpaint Back in 5 minutes Staff Member Moderator Elite Explorer

      Joined:
      August 1, 2008
      Messages:
      9,722
      Likes Received:
      673
      Trophy Points:
      133
      City, State:
      STL MO
      Year, Model & Trim Level:
      Modified 95 XLT
      Been waiting for somebody to mention that. Lol

      Hinge screws don't come near anything at all. I cut the self drill ends off after install just in case, but didn't need too.

      The connector box is tight, and zero side to side or up/down movement. I used longer Stainless bolts for the quick fists. These act as stopper's on the backside of the harness connector, and "Lock" it in place for front to back movement. I need to get a set of Mini quick fists to replace these. They use the same hardware. I just used what I had at the time.

      I posted the pictures without the wire grommets added. They finish off holding the cables tight and safe.

      There is also 4 weep holes for drainage.

      I messed up the paint on top (still soft) when clamped to the tube for drilling bolt holes, and was going to change pics when done fixing. You beat me to it, as that pic would show the grommets. Lol

      sq cog grommet.jpg
       
      Last edited: January 1, 2019
    8. toypaseo

      toypaseo Flunked daycare Elite Explorer

      Joined:
      January 3, 2003
      Messages:
      6,602
      Media:
      28
      Albums:
      1
      Likes Received:
      248
      Trophy Points:
      83
      City, State:
      outside shovelling snow
      Year, Model & Trim Level:
      ................ 96 XLT ™
      That's good news :thumbsup:
       
    9. jad2411

      jad2411 Elite Explorer

      Joined:
      October 29, 2006
      Messages:
      2,141
      Likes Received:
      3
      Trophy Points:
      58
      City, State:
      El Paso, TX
      Year, Model & Trim Level:
      2007 Brown eb
      Why would you do that? :facepalm: :crazy:

      Jk hope you feel better
       
      • Like Like x 1
    10. gmanpaint

      gmanpaint Back in 5 minutes Staff Member Moderator Elite Explorer

      Joined:
      August 1, 2008
      Messages:
      9,722
      Likes Received:
      673
      Trophy Points:
      133
      City, State:
      STL MO
      Year, Model & Trim Level:
      Modified 95 XLT
      Thanks J.

      Surgery tomorrow morning. Should be back in action soon, and starting the next mod.
       
    11. CDW6212R

      CDW6212R Hauls the mail. Elite Explorer

      Joined:
      June 17, 2004
      Messages:
      18,489
      Media:
      3
      Albums:
      1
      Likes Received:
      834
      Trophy Points:
      143
      City, State:
      Knoxville, TN
      Year, Model & Trim Level:
      98 Limited AWD
      Best of luck with that dentist trip. I've had one tooth break the back edge of three times now, the last time I got him to shorten the opposing tooth etc.

      Make him take his time when refitting(final grinding) the new tooth parts to match the others. Be sure it feels comfortable and not grinding, or catching, before saying it's all good. You don't want to have to go back again from a high stress point(like I had twice before). This time I think he got mine mated well.
       
      • Like Like x 1
    12. gmanpaint

      gmanpaint Back in 5 minutes Staff Member Moderator Elite Explorer

      Joined:
      August 1, 2008
      Messages:
      9,722
      Likes Received:
      673
      Trophy Points:
      133
      City, State:
      STL MO
      Year, Model & Trim Level:
      Modified 95 XLT
      Thanks Don.

      Not looking forward to it, but I am, at the same time. Had enough of raw open nerves to last me for a while.

      Sleep deprivation is a real thing. Lol
       
      • Like Like x 1
    13. RockRanger

      RockRanger Elite Ranger Elite Explorer

      Joined:
      January 14, 2001
      Messages:
      6,149
      Likes Received:
      143
      Trophy Points:
      83
      City, State:
      Fresno CA
      Year, Model & Trim Level:
      86 ranger no more
      Callsign:
      KK6TDL
      Finally caught up with this thread. Wish I would have seen the thread before I checked out the trailer in person. A few things I saw in the pictures I missed in person and was cool seeing the fab side and how it looks now. Can't wait to see it on the trail.
       
      • Like Like x 1
      • Thanks Thanks x 1
    14. gmanpaint

      gmanpaint Back in 5 minutes Staff Member Moderator Elite Explorer

      Joined:
      August 1, 2008
      Messages:
      9,722
      Likes Received:
      673
      Trophy Points:
      133
      City, State:
      STL MO
      Year, Model & Trim Level:
      Modified 95 XLT
      Thanks @RockRanger. Was a pleasure to show it to you, and great to see you again.

      Your only the 2nd forum member to see it so far. Other than this thread, I haven't had someone to share what has been taking up all my spare time.

      Thanks for the interest in it, and not nit picking my flaws. Lol

      Had a complication with my surgery last Tuesday, and ended up back in today for more cuts, and more stitches. Might be a bit before I can really do anything strenuous with this trailer.

      I will do what I can, when I feel up to it tho. It's killing me not to be working on it. I might have a screw loose. Lol
       
    15. gmanpaint

      gmanpaint Back in 5 minutes Staff Member Moderator Elite Explorer

      Joined:
      August 1, 2008
      Messages:
      9,722
      Likes Received:
      673
      Trophy Points:
      133
      City, State:
      STL MO
      Year, Model & Trim Level:
      Modified 95 XLT
      Bored AF today. Over a foot of snow today, and resting up after oral surgery (twice) has made Jack a Dull boy.

      I decided to deal with the pain, and not take any pain killers, so I could work a little on this a little. Just the start of a new project, nothing physically hard, just needed my wits for it.

      Have had materials for this for sometime now, and the main part arrived last week. Staring at it just sitting was driving me nutty. Ok, now that the BS is out of the way.....

      Ordered a Solar kit from Renogy the beginning of December, taking advantage of the holiday sales, to save some $$. 25% off helped on this, and they offered free shipping with the kit on top of it. Kit includes a 100w panel, 30amp Wanderer smart charger, Z mounting brackets, and all the basic Mc4 wiring.

      I mentioned early on in this thread my idea of how I wanted to mount the panel, and have had time to think it thru since. I picked up two 6'Lx 1.5" alum angle, 2x100 lb full extension smooth bearing sliders, 4'L x1" Alum channel, 2x1.5" U-bolts, and a bunch of misc stainless hardware.

      Solar slider materials.jpg

      Cut the angle the same length as the sides of the solar panel, making 4 pcs. Clamping two 2x4's to the table at the exact width of the roof rack, I used this as my work space for measures, to get the mounting track widths. With this "Jig", it was easy to line everything up and mark, drill, and bolt it all up.

      solar slider side view open.jpg
      Solar slider partial open top view.jpg
      solar panel tray complete.jpg

      It is mounted under the roof rack in the front, and slides out the front when in use. Slid back under the rack, kept safe under the tent, and locked in place, when not in use. The U-bolts in front, are for support straps of some sort (to be determined later) when fully extended and in use. Sliders are good for 100 lbs each, and this panel weighs 25 lbs, but with time/use, wind, snow, what ever, I thought the extra support couldn't hurt it. It is very firm when extended, but yeah, safer choo for the chooching.

      SP in 3.jpg
      SP in 4.jpg
      SP out 1.jpg


      Wiring it all up is a job in itself, and after that, still one more modification build to be done to it. Had to order an inline exterior 30 amp fuse, and a 30 amp circuit breaker for the charger to battery, inside the T-box. Should be here in a few days.

      I think I did pretty good for a dead man walking today.
       
      Last edited: January 13, 2019
      • Like Like x 2
    16. CDW6212R

      CDW6212R Hauls the mail. Elite Explorer

      Joined:
      June 17, 2004
      Messages:
      18,489
      Media:
      3
      Albums:
      1
      Likes Received:
      834
      Trophy Points:
      143
      City, State:
      Knoxville, TN
      Year, Model & Trim Level:
      98 Limited AWD
      I like it, that's a big panel.

      I want to find a small one too for battery maintenance on a couple of my cars.
       
      • Like Like x 1
    17. gmanpaint

      gmanpaint Back in 5 minutes Staff Member Moderator Elite Explorer

      Joined:
      August 1, 2008
      Messages:
      9,722
      Likes Received:
      673
      Trophy Points:
      133
      City, State:
      STL MO
      Year, Model & Trim Level:
      Modified 95 XLT
      Renogy has one bigger, but is too big to fit between the rack rails.

      This one panel will work for my needs. I don't have anything that will drain the batteries past 50% discharge overnight, and this should top them back up in a few hours. If I ever need more, the charger is expandable up to 400 watts. I could plug in a roll up panel or a suitcase panel to add to it.

      Time will tell, after some actual usage, and seeing what my real consumption will be.
       
    18. gmanpaint

      gmanpaint Back in 5 minutes Staff Member Moderator Elite Explorer

      Joined:
      August 1, 2008
      Messages:
      9,722
      Likes Received:
      673
      Trophy Points:
      133
      City, State:
      STL MO
      Year, Model & Trim Level:
      Modified 95 XLT
      Found a container for the first aid storage I liked. It is a take along 6 meal packer, sold at Sams Club. Has a nice soft side material, and a soft cooler liner. Zipper front panel, and a small zipped rear pocket. Has 2 mesh pockets on the ends, and a removable shoulder strap. Came with a power drink mixing cup, and a small water tight 20 ox cup with a freezer gel insert. Won't be using these obviously, but I will be using the 6 clear storage containers with snap on lids.

      I picked up another large First Aid kit that had different items then the one I already had. Its a 351 pc with a lot of Eye care & Burn stuff, and specialty items like face shields. The other kit is a 326 pc. These kits are nice, but are bulky, and they can be a nightmare to deal with when using in an emergency situation. Most everything in these are in loose trays, and can spill out very easily on uneven terrain outside.

      Was able to combine both kits into this meal packer, and is 1/3 the size of them. Everything is sorted and like items kept together, for easy access, and clear containers for identification at a glance. Instant ice packs, and 2 freezer ice gel hard packs, and a snake bite kit are stored as well. Large gauze pads, and longer items are simply kept in a freezer zip bag. Trauma and field aid instruction booklets are tucked away Just in case. The back side pocket will keep an old charged cell phone for 911 calls.

      I will add to it as I find stuff. I want a good specialty field kit, with tourniquet's, stitches, and an emergency Tracheotomy. Will most likely get the My Medic kit for that. Hemostats, and other tools as well. Need to refresh myself, and take the first aid classes again. Been a few years since I did those, as the kids are grown and flew the coop.

      FA1.jpg
      FA2.jpg
      FA3.jpg
       
      Last edited: January 14, 2019 at 11:32 PM
      • Like Like x 2
    19. gmanpaint

      gmanpaint Back in 5 minutes Staff Member Moderator Elite Explorer

      Joined:
      August 1, 2008
      Messages:
      9,722
      Likes Received:
      673
      Trophy Points:
      133
      City, State:
      STL MO
      Year, Model & Trim Level:
      Modified 95 XLT
      Solar part 2:

      2 of 3 items arrived and I got as far as I could today with wiring this panel up. Inline 30 amp-1000voc solar MC4 fuse, and 30 amp inline circuit breaker.

      The negative ground PWM charger lets excess power to be converted to heat, and is finned on the back (behind a heat shield) for that heat to escape. Because of this, the chargers should not be mounted flat, as the heat would rise thru the unit. This is what I'm told by Renogy tech support at least.

      Not wanting to bolt this to the T-box wall panel, having more holes, and bolts sticking thru it, I opted to make a mount that bolts to the shelf. It's not straight vertical, as I wanted a slight angle for the stiff jacket 10 awg wires, that insert on the bottom. I placed it near the box vent.

      Here is the backside of the charger with the mount, the fuses, and the MC4 wiring.

      20190116_160131.jpg

      I ended up mounting the 30 amp circuit breaker to the box mount, with a flat 1/16"x1.50" aluminum. This little breaker is pretty slick. It's waterproof, and I can use it as a switch for the solar system, as the charger is directly wired to the battery.

      20190116_181641.jpg

      For those that don't know, always hook a solar charger to the battery first, then after power is is verified, only then can you hook up the panel. Chernobyl events will happen, if you do it the other way. This charger is a no frills smart charger. No frills as in no LCD display, but does everything those do for cheaper. lol I have a LCD battery monitor in mind, I want to use, but mounted elsewhere for easy visibility, so opted for this unit.

      After the charger wires was ran and hooked up, I switched gears, and attacked the panel wires.

      Installed the inline fuse, and routed the wires along the panel using a couple zipties, then some stainless rubber lined pipe clamps. These keep the wire jackets from rubbing on any metal edging. The jacket is very thick and stiff, and will hold up well, but status quo says add extra protection anyways.

      Deciding on where the slack line should reside was a coin toss, plus I am on pain meds from surgery, and figured best leave it to luck. lol Choice was in front or in back, each have their own complications. Front won, so the wire is tight along the panel up to the front, with the side routed on top in the gap between panel and slider, dropping thru the U-bolt. With the slack needed for the slide in/out, it was then ran down the front of the main box. I used more stainless rubber lined clamps, using the existing trim bolts, and ran across the expanded metal to the T-box.

      Solar Inline 30 a fuse.jpg
      Solar wiring in panel track.jpg
      solar wiring down main box.jpg

      This is where I stopped. The stainless 6-12mm cable glands did not show up yet, and I need them to know what size holes to drill in the back of the T-box, to run the wires to the charger. That's it, 2 wires is all that is needed for this trailer to have solar powered battery charging. So close to having another system completed! :party:

      The MAGM batteries have 115 Amp hours each, with a total of 230 Ah. But..... since your not supposed to let them drain past 50%, the total Ah's is really 115 Ah. This amount should last a few days at a time running everything onboard, before a charge is needed, but with 3 methods of charging, these "Should" never reach a 50% drain, and definitely not near that over one night of use.


      So I don't feel like I am talking to myself here, how about...... :feedback: good or bad, let me know how I'm doing please. I'm not a trailer builder, I'm just building a trailer, and everything is brand new to me here. Thanks!

      Edit: Today I realized that letting fate decide (coin toss) on 2 ideas, while on pain killers, is not a good idea. lol I am re-doing the wire routing for this panel, so the wires look better, work better, and doesn't interfere with anything. Had to order more stainless clamp mounts for the new routing.
       
      Last edited: January 19, 2019 at 1:55 PM
    20. BKennedy

      BKennedy Elite Loser Staff Member Moderator Elite Explorer

      Joined:
      November 29, 2000
      Messages:
      6,078
      Likes Received:
      473
      Trophy Points:
      103
      Location:
      USA
      City, State:
      San Diego, PRofK
      Year, Model & Trim Level:
      1994 XLT
      I have that same solar charge controller in the RV. I wanted a no-frills controller because I have all kinds of crap in there already to tell me battery voltage.
       
      • Like Like x 1
    21. gmanpaint

      gmanpaint Back in 5 minutes Staff Member Moderator Elite Explorer

      Joined:
      August 1, 2008
      Messages:
      9,722
      Likes Received:
      673
      Trophy Points:
      133
      City, State:
      STL MO
      Year, Model & Trim Level:
      Modified 95 XLT
      Yep, same here. Reviews on this charger are positive, does what's needed, and has a 5 yr warranty.
       
    22. CDW6212R

      CDW6212R Hauls the mail. Elite Explorer

      Joined:
      June 17, 2004
      Messages:
      18,489
      Media:
      3
      Albums:
      1
      Likes Received:
      834
      Trophy Points:
      143
      City, State:
      Knoxville, TN
      Year, Model & Trim Level:
      98 Limited AWD
      You are killing it, meaning good, badass etc. I hadn't thought of how to connect the controller and panel. I have a small $20 Battery tender model for small panels, it may be 2x3" and not thick.

      I wish/hope the LiFEPO4 batteries evolve a little more. Those weigh nothing but can only take a limited amperage amount. The ones I like can handle just 60amps from an alternator, and at $350 you can't afford to buy three or four to get that up past 140amps or a typical alternator.
      https://www.amazon.com/dp/B00H0NIJO...colid=246RRPWYWS26&psc=0&ref_=lv_ov_lig_dp_it
       
      • Like Like x 1
    23. gmanpaint

      gmanpaint Back in 5 minutes Staff Member Moderator Elite Explorer

      Joined:
      August 1, 2008
      Messages:
      9,722
      Likes Received:
      673
      Trophy Points:
      133
      City, State:
      STL MO
      Year, Model & Trim Level:
      Modified 95 XLT
      Thanks Don! :)

      The Lithium Ion batteries wanted to use for this thing, are crazy expensive! Way out of this poor mans budget. I'm with you there, and hope they do evolve and come down on price.

      https://www.amazon.com/dp/B07FDHRP4...&pd_rd_r=a482616b-1b5c-11e9-85ad-2949e9cdafab

      There is another alternative for mobile power. It's a methanol burning generator that you can buy the fuel by the jug. One jug would last me a year $80/ea. Like $40/Liter for it, and is available in many places across the country. The size I would use is about $1000 total for everything. It's silent, clean power, and self efficient. I think I would go this route over the high priced Lithium batteries and solar combined.

      The eco-friendly power source for your RV | EFOY
       
      • Useful Useful x 1
    24. CDW6212R

      CDW6212R Hauls the mail. Elite Explorer

      Joined:
      June 17, 2004
      Messages:
      18,489
      Media:
      3
      Albums:
      1
      Likes Received:
      834
      Trophy Points:
      143
      City, State:
      Knoxville, TN
      Year, Model & Trim Level:
      98 Limited AWD
      That's great. I love the options for being off the grid and have plenty of power. I like that Renogy brand too, those seem to be fine with using in a normal vehicle(add in parallel to the main battery). If the price was right, I'd want to put one in the rear corner of my truck. Some are small enough to fit in tight spaces(6.5x3.6x4.4" etc).
       
      • Like Like x 1
    25. 410Fortune

      410Fortune ELITE BRONCO2ERER Staff Member Moderator

      Joined:
      August 3, 2000
      Messages:
      22,861
      Likes Received:
      341
      Trophy Points:
      103
      City, State:
      7B Panhandle
      Year, Model & Trim Level:
      B2 Mod
      You're telling me!
      Trailer is looking awesome BTW
      Earlier this year I pulled the trigger on switching our whole house from flooded lead acid to Lithium Ion batteries.....we went from 16ea 6v batteries to 8ea 12V lithium batteries. I wanted to get 12, but they are so expensive the other 4 have to wait. So far it was SOOOOO worth it, these batts outperform the old lead acid about 3:1 for output and 5:1 for charge time..... I can't wait to get 4 more
      We are 100% off grid with a 48V system, solar and propane/gas/diesel generator options
      So far its been worth the investment and time to save the $$$$ for the Battle Born LiFeP04 batteries they are awesome!!
      [​IMG]
       
      • Like Like x 1
    26. gmanpaint

      gmanpaint Back in 5 minutes Staff Member Moderator Elite Explorer

      Joined:
      August 1, 2008
      Messages:
      9,722
      Likes Received:
      673
      Trophy Points:
      133
      City, State:
      STL MO
      Year, Model & Trim Level:
      Modified 95 XLT
      That's awesome!!! Congrats on getting away from the "Man" and being as self sufficient as possible. And thank you!

      I seen those battleborn units for less than $1k/ea. Always great to get a good review, of a product I know nothing about. A big bank like that warrants a bank loan. Lol
       
      Last edited: January 18, 2019 at 6:58 PM

    Share This Page







    We Support Our Troops!