Search results | Ford Explorer - Ford Ranger Forums - Serious Explorations
  • Register Today It's free!

Search results

  1. P

    2 DOOR Fuel Pump Access Hole Installation

    There is a company(SUR&R), that makes replacement fittings, there fuel lines need to be installed in there heat shield.
  2. P

    2 DOOR Fuel Pump Access Hole Installation

    1. That must be pressure switch for the EVAP system. the green valve is a vent for the EVAP system( turn it counter clock wise to unlock and remove while pushing down on it. 2. I had the same problem with the pump bolts. One bolt I could not remove, so I cut it off. If you cut a small piece...
  3. P

    1999 Explorer Axle Shaft Replacement

    FYI, there thread sealant on the thread by ford and only 7 or 8 ft/# of torque on the plug. If you heat the plug up with a small tank torch, that might soften the thread sealant. Once it, break the seal on the plug, myou can remove it by hand. Look for my post about replacement plug. I wire...
  4. P

    Replacement rear diff fill plug! Where do you buy a new one for 95?

    The plug was not available at rockauto, no listing at autozone, advance and o'reillys. Only summit, and NPD show the plug in stock, but not listed for the explorer.
  5. P

    Replacement rear diff fill plug! Where do you buy a new one for 95?

    Just order a new plug from national part depot. They list the plug by ford part number
  6. P

    freez plug clinder head

    If you order a freeze kit ( say from rock auto or similar store) the right size plug come in the kit.
  7. P

    Fuel pump question.

    Floor are made of 16 gage
  8. P

    Fuel pump question.

    All fuel pump fail at some time. One thing you did not try or do; is disconnect the fuel filter and turn the key and see if the fuel is coming out of the fuel line. The pump is not that bad too replace. Just a note!! When I drop my tank my tank strap was broken (TSB). My 95 the filler pipes...
  9. P

    Rear door strike plate holder FELL INTO BODY. Help!

    Phillips head screw on the bottom rear of the panel by the rear hatch. There is a torx bolt for the seat belt.
  10. P

    1997 SOHC EB Explorer Vibration

    Balance your tires. U could move your rears too the front. See what happens. Before u rotate your tires with ithe vehicle in the air, spin each wheel by hand, look at the tire straight on too see if the rim Or thread has shifted. I had the same trouble with a rental, at speed below 65, the car...
  11. P

    Replacement rear diff fill plug! Where do you buy a new one for 95?

    Replacement rear diff fill plug! Where do you buy a new one for 95? Are all the rear diff Fill plug the same for all the years? Are all the rear diff Fill plug the same for all the makes and model fords?
  12. P

    Locks are not locking when in drive

    Maybe you have the setting turned off. Look in your owner manual on the Setting up the setting.
  13. P

    98 XLT - a/c clutch engages, then clicks and remains off(?).

    Then maybe a loose connections at the connectors. Check the low pressure switch connector on the filter dryer and the connector on the compressor. If you have a multi meter check the resistance the switch on the filter/dryer. It should read close circuit(0) this also tell you the system is...
  14. P

    98 XLT - a/c clutch engages, then clicks and remains off(?).

    Your problem could be cause by a few simple things. But I need more information. The static pressure just tell me there is some gas in the system. 1. What was the outside temperature when you read the static pressure? 85 degree F? 2. Did the system just stop cooling? Monday you have AC , tuesday...
  15. P

    Console Armrest - Options for fixing split/cracked covering?

    I went too joe_Ann fabric store, and brought a yard of material. I brought the lid with me too match the color. Its held in place with Stapes . I believe quarter inch in length (homedepot). EB4x brought a replacement kit on Ebay.
  16. P

    How to: Overhead console display fix - 2nd Gen

    ? How did you clean up the pcb board? What did you uses?
  17. P

    Signal/washer stick help wanted

    I had the same issue ( from the factory), I just replaced it. They are cheap.
  18. P

    Hood latch- hood does not pop up

    I can't get the hood open. I lube the latch. Turdle state I can adjust the handle
  19. P

    Hood latch- hood does not pop up

    Is there a spring on the hood? My hood does not pop open. The hood latch (lock) works fine with the hood open; when I lock and unlock the latch
  20. P

    Infor on oil pressure switch for gauge on 95 explorer

    I just replaced the oil pressure switch for the gauge. I used motorcraft SW-2220 (E9SZ-9278A). Torque 12 -18 ft/#(FSM). I used a oil pressure switch socket(from autozone). What I checked before replacement, Is how it worked. Result are: if I grounded the wire the gauge showed 1/2 way on the...
  21. P

    Anybody have these terminal ejectors / kits ?

    Yes, I have two sets, they work great. Used them , when I replaced shift motor. And on a small 4 pin barrel connector
  22. P

    Pre-fab tube with steel flare nut fitting leaking

    I replace the steel fitting with a brass fitting and the connection seals.
  23. P

    Pre-fab tube with steel flare nut fitting leaking

    I am repairing some steel tubing and I am using flare fitting and brass union (coupling) too joint the lines. I purchase pre-fab brake tube with flare fitting that are steel and also the mating brass union. Problem I am having the steel fitting are leaking at the connection. Has anyone else...
Top