Search results | Ford Explorer Forums - Serious Explorations

  • Register Today It's free!

Search results

  1. M

    Egr vacuum solenoid wiring pictures.

    Help! Any one Have a good picture of the wiring harness? Wires pulled out from the connector, and lost track. Red and purple.
  2. M

    ECT Sensor Queastions

    Thank you !
  3. M

    ECT Sensor Queastions

    Broklynbaby, Do you still have access to the ect chart. Link is not working Thanks
  4. M

    What did YOU do to your Explorer today?

    Changed out that amazingly hard to get at O2 sensor on the drivers side. The threaded sensor.....easy ! That damn wire harness.....that took some stretching. lol
  5. M

    4x4 noise (banging thud) at front dif. ????

    Have not explored it much yet. Yours looks like the U-joint is good, but I'm thinking the carrier bearing in the front dif. may be sloppy.
  6. M

    4x4 noise (banging thud) at front dif. ????

    Haven't had much time to do alot of trouble shooting, but here goes... Transfer case engaged with hubs unlocked = no noise hubs locked with transfer case disengaged = no noise hubs locked with transfer case engaged = banging comming from drivers side front end. replaced ball joints...
  7. M

    disabling 4wabs by pulling relays

    As far as the 2nd gen's.....I really have no idea.... But, you are correct, there are some very smart people on this sight. To answer my own question in a way, there are 2 30amp fuses in the under hood fuse box marked ABS. I pulled both out, assuming one's for the front, and the other for...
  8. M

    disabling 4wabs by pulling relays

    Let me first apologize for starting a new thread on a subject that's probably been beat to death. I live in New Hampshire...I hate my ABS! I have been searching for a straight forward answer on how to disable my 4wabs. One post I found says to pull both relays from the under hood fuse box...
  9. M

    Disable 4w ABS 1994 Ex EB

    I attempted pulling both, and my EX would not start afterwards. Put both back in, and it started.
  10. M

    Coil spacer dimensions

    Thanks. Do you happen to know what the diameter is at the top(part that fits inside the spring) of the spacer? I don't think I will be using the plastic insulator or the bell shaped seat.
  11. M

    Coil spacer dimensions

    I have a set of Daystar coil spacers installed in my vehicle. Looking to make a set of aluminum ones. Any body have dimensions or a blue print? Kinda hard to measure the ones on the vehicle.
  12. M

    Looking for a east coast connection (NH)

    Looking for a fab shop in New Hampshire, or atleast North East, that can do cut and turned beams on a first gen. Anybody have a connection?
  13. M

    Need step-by-step guide for changing Canister Purge Valve

    I used a long pair of forceps (tong like devises) to reach in and grab the hose, and pulled it into a position where I could grab a hold of the valve. It's kinda like a puzzle, pull backwards, pull to the right, twist a little....It will come out. when you get it, you'll have to twist/turn...
  14. M

    camber shims for a 92 navajo

    Top photo: New 2 3/4 degree Napa shim next to stock 2 1/2 degree shim Bottom photo: snap ring angle not parallel to bushing face. Returned to Napa today!
  15. M

    camber shims for a 92 navajo

    I understand that there suppose to be the same, minus the degree change between 2 and 4 wheel. My issue is that when I added my spacers, I rotated my stock bushings (2 1/2 degree) 180 degrees.hence I went from 2 1/2 degrees positive camber to 2 1/2 degrees negative camber. my allingment was...
  16. M

    camber shims for a 92 navajo

    Avoid Napa for the time being, I have a 94 explorer with 2" coil spacers, just got some bushings from them.... definitely the wrong ones. bushing says it can be used for the 4x2 or 4x4....not so much! Still working on resolving this issue. Try advance auto, they carry moog products.
  17. M

    spindles

    Thanks. Just found these on Broncograveyard.com # 82007 New Dana/Spicer Spindle 1993-94½ Ford Explorer with front ABS Price: $129.00
  18. M

    spindles

    Does anybody sell spindles for a 1994 ford explorer 4x4 xlt, other than the dealer?
  19. M

    1993 Ford Explorer. The starter won't turn over, and it just clicks.

    Give the starter a wack with a hammer, then try to start it.
  20. M

    6mm bolt location on the front ABS sensor.

    Did my u joints 6 months ago. Yes it is on the inside surface of the steering knuckle. Had to use a 10 mm deep socket with a 1/4 " drive (tight fit). Find the sensor, and the tear shaped bracket, note the small hole in the bracket, look on the opposite side, you should see the bolt head.
  21. M

    egr pressure sensor cleaning?

    To answer my own question: gasket, circuit board, diaphram, insulation material. nope not rebuildable! Yup, took it apart, had to check for myself.
  22. M

    egr pressure sensor cleaning?

    Is there a way to clean or rebuild a egr pressure sensor? The aluminum housing is riveted together, nothing a drill and some new bolts wont fix. Has anyone taken one of these apart? What's inside?????
  23. M

    Cold Air Intake

    I am looking into purchasing a Kurtz Kustomz air intake, It replace the stock box pretty much like your photo.....Question I have is, What is done with the two vacumn lines that attach to the old air box?
  24. M

    Cold Air Intake

    The tube your talking about pulls warm air from the manifold during startup or during cold temperatures to increase drivability. Cold is good, but too cold things run like crap.
  25. M

    clicking from front wheel

    Could be worn ball joints, could be a missing anti rattle clip for the brake pads?
  26. M

    Rim sizes, will stock 97 rims fit on a 94?

    Thanks! You guys rock!
  27. M

    Rim sizes, will stock 97 rims fit on a 94?

    I have been searching the site for a while, and havent found the answer i'm looking for yet. Sorry if this question has been asked numerous times. My buddy is scraping a 97 exdplorer, will the stock rims fit on a 94? concerned about the hub, and the center bore. thanks.
  28. M

    Spring Spacers

    So, the spring spacers are done, wheel bearings, axle seals, wheel seals, and U-joints....Great weekend. So now my tires sit at the classic V shape, caster/camber allingment bushings? Where to get them? and how extreme can I go?
  29. M

    Axle Shaft Spacer & Snap Ring - How important are these?

    1)Is he refering to the (2) thrust spacers, that go with the Automatic hubs? 2)Or is he refering to the spacer (axle shaft)that has teeth cut into it? 1= Dont have them on mine 2=absolutly critical!!!!!!
  30. M

    Spring Spacers

    I did a BroncoII a cople years back, not fun! 4x4 presure treated post + 5 pound sledge = lots of sweating + no luck. That was a nightmare, 2 days, and a new axle shaft latter. Hope it's easier this time around. New Hampshire is great for rust! Im going to name it the Titanic!
  31. M

    Spring Spacers

    Thanks! I was just looking thru old post, and the general answer is 1-1/8" Kinda forget about the search feature. Have been soaking for 2 wks. now. Tommorrow is hell day...... 2" spring spacer wheel bearings u joints Gotta Love how those spindles come off..."just tap it with a...
  32. M

    Spring Spacers

    Installing a set of Daystar 2" coil spring spacers tomorrow. Does anyone know the size of the nut, for the spring retaining stud???
  33. M

    Lower shock mount

    Thanks, exactly what I was looking for. Coat hanger to keep shock on stud, Your gone. Nice write up and pictures.
  34. M

    Lower shock mount

    Installed new shocks on my 94 4x4 this weekend, all went well until....snap, damn...broke the threaded section off the lower shock mount, passenger side. They appear to be a stud welded in place, any repair tips/tricks????
  35. M

    Master cylinder, hydraulic abs?

    How does one check it? I've been doing some reading, and i'm wondering if the ABS hydraulic unit has air in it, Which I have come to find out, traditional bleeding methods will not remove the air from it, It must be brought to a garage.
  36. M

    Master cylinder, hydraulic abs?

    No fluid loss at all. Checked all connections. With vehicle off, I can press the brake pedal twice and have good brake feel. As soon as it is started, the pedal goes to the floor.
  37. M

    stiffer rear suspension

    Bigger rear sway bar, poly bushings?
  38. M

    Master cylinder, hydraulic abs?

    Brake issues, Picked up this 94 xlt for free a few months back, replaced all the brake line as it was rotted out. Brakes have been good for a month, last week the pedal started going to the floor periodically, now all the way. Not loosing fluid, seems like only the rear brakes are stopping...
  39. M

    Newbie saying hello

    Free Rocks! Rented a tow dolly for 65 bucks, 1 headlight, 1 taillight , about 50 bucks in break line and fittings....as close to free as can be. Picked it up from a relative, her daughter lost her license 2 yrs ago, and probally isn't getting it back, vehicle sat for 2 yrs. I guess they got...
Back
Top