Search results

Well if I end up going you can ride along with me out there and we'll have all the food set. I don't have a trail rig, just going out to check it out. ed@screamingbroccoli.net

If work permits a trip out then I'm in. Is there a place to put a Toyhauler? I'll bring the Quad and anyone that wants a turn on it is welcome. Honda 650 Rincon. Chris- It can get a bit chilly out there in the winter so pack some warm gear for sleeping. My Buddy has some land out near...

my bad- it's just that people "recommend" a welder by calling it an Arc welder-this leaves the recommendation a little open, don't you think? It's the same as "get your self a locker". You can still get the rods: //www.jwharris.com/welref/techguide/misc_items/arc_goug/

Ok. Mig is Arc. Arc is electricity. Stick is Arc. Arc is electricity. Tig is Arc Arc is electricity. Spindle is correct- If you really want to start with learning how metal reacts an O/A set up is where you start. You weld with that and you are good to go. Mig, Stick, tig all follow...

Check out this thread: http://www.explorerforum.com/forums/showthread.php?t=129935&page=2&pp=20

Hotwheels, You should be geting better performance out of your 230v welder. It should be able to do 1/4, solid wire with gas. Ed

http://www.weldingmart.com/Qstore/p002054.htm This comes with the gas regulater so all you have to do is buy a tank. As mentioned a 220v is a better choice because you get twice the welder for just a bit more money. But at 370.00 this 115v is a sweet deal. You can do heavier material, you...

(4) This section shall apply to all motor vehicles. if you go to the site and click on Colorado this is the last line in the penal code, so I guess you do have to comply with CO's rules.

CO= 2 Phase Law: 4 inches or AS-1 / NO / ANY / ANY / 1989 4 inches or AS-1 / 27% Net / 27% Net / 27% Net / 1989 Note : No mirrored tint is allowed. Enforcement Note : The fine for being in violation is $50 and the driver is not usually required to fix the windows. Tint shops are not...

TTG and Rome are correct- you are required to follow each State's guide lines reagrding window tinting and various mods. http://home.pcisys.net/~bpc/auto_law/tint/

I can't say for sure on a 98' but for mine, a 93', you just have to pull on them and they are a PIA.

http://www.harborfreight.com/cpi/ctaf/Displayitem.taf?itemnumber=34542 or:

Ok ya can't put those two bikes in the same sentence :D The Rebel is a 250cc death trap!!! I only say this because it can't get out of it's own way. If you weigh about 50lbs, maybe this is a good bike but otherwise I find those bikes dangerous for anyone over 125lbs. I borrowed a friend's for a...

Even the 750s have a low seat height. Just keep sitting on the bikes until you find the one that fits. The power wont be a problem. Does the Army require the riding school? My dad was AF and for me to be able to ride on base I had to take a week long riding course. Of course I hated it at the...

Japanese 750s are plenty big. Some may suggest a bike in the 650 range or even smaller. My first bike was a 87 Shadow 700 but I did have some experience with dirt bikes. Damn I'm gettin' old! What really sucks about bikes is that you can't really test drive them like cars. Go to every dealer and...

here is some more info on the HF bender: http://www.hobartwelders.com/mboard/showthread.php?t=12595

While the wheels are off, the front calipers are pulled and the slides are greased. This schedule seems to keep the warped-rotor devils at bay. I have used EP-moly wheel bearing grease for this service, but changed to a waterproof synthetic at the last service. Same on the steering, BTW. The...

You don't have any recourse since you already signed off on the work order as well as paid, unless it states they used MC and something else is on your truck. As everyone has mentioned that's about right for having a shop do the job but now that the pain is over, keep a religious schedule on...

http://www.4wheeloffroad.com/howto/3336/

I'll put some money on the MAF. What Creager described is what mine was doing. My MAF connection has only one clip so it came loose- Zip tied it and hasn't bothered me since. Good Luck

he pretty much said that it's just a pain in the ass but it is cheap. Looking at the 2 links you listed I would go with the Tools Plus- seems like a better Co. to deal with. Not a big fan of HF because the store here is useless.

DeRocha, I've been in the market for a bender as well and got some input from a Weding Forum I belong to: This is the quality of the HF model that was posted.

?????http://www.golight.com/solutions/

http://www.golight.com/products/golight.html

maybe flip it.....