Search results

It appears the APIM has died on my wife's 2012. It sounds like this is becoming a common problem, so I'd like to replace it with one that won't die again, which I believe means a 2015 or 2016 APIM. I've noticed the 2015 APIMs are missing a connector, the grey connector shown in the link below is...

I'm in the process of bench bleeding my master cylinder and slave cylinder. How do I know that the slave has been properly bench bled? Should I be able to move it by hand when it is NOT connected to the quick disconnect line? (Not connected to anything?) The master is bled...can't move it...

I got this center console from work and am thinking about selling it...but I need to know what it is from. It looks like it is from an Explorer...anyone recognize it?

Truck is a 94, and the alternator light stays on and the gauge is on the "N" in normal. Only until I rev it to 3000rpm or higher, then everything goes back to normal. Normally it's on the "M". Alternator is new (last week) the belt tensioner(today). It seems to be working a little...when I pull...

My 1st/2nd synchro is shot. I can't even shift normally, I have to shift extremely slow. I'm wondering if I can replace the synchro myself, and what special tools would be needed if any. History: About 35k ago, and 3 years, I had the trannsmission rebuilt (The truck had 95k on it at the...

I'm in the process of changing ball joints, and am now reassembling everything. I put the tie rods back onto the steering knuckle, and tightened the nuts down to the required torque specs. I went to put a new cotter pin in, and the cotter pin hole is even with the top of the nut! When I took...

Anybody have any tips for replacing the bearing inside the spindle? I know its in the middle of the spindle and looks like a PITA to get out. Thanks!

Anyone know what the stock throttle body size is for the OHV 4.0? I measured mine, inside diameter, at the outer most point of it (closest to the front of the truck) and it was 63mm. Either I have an aftermarket TB on (possible, I bought the truck used) or I'm measuring at the wrong spot.

I've had this clanking sound in my truck for a long time now, and it seems to ge getting louder. It seems like its coming from the suspension, as it only does it when i go over bumps. BUT it does NOT do it when I'm going over bumps and I have the brakes on? There is a slight noise when the...

My tranny needs a rebuild, at least the input bearing is shot. I got a quote of $1200 to replace that bearing and a bunch of others. I'll save almost $400 if I take the tranny out myself. So how difficult is it to change those bearings? I've never even seen a tranny apart...but I'm not afraid to...

Here's the deal...the clutch wore out on my ranger so i replaced it with a centerforce dual friction, replaced slave cyl. and throwout bearing, pilot bearing, and hydraulic line going from the master cylinder to the slave(I broke the old one). Now its all back together and the slave isn't...

I'm talking about the shaft that goes to the engine. I have my tranny sitting on my garage floor right now, and that shaft wiggles slightly. I've heard that is normal but I'm not sure. Anyone have anything to add on this? Thanks!

I'm replacing the clutch on my Ranger and need to get the line off the slave cylinder. The Haynes manual says I need a special tool. Do most auto parts stores have this tool? Or is there another way I can get it off? Thanks. Adam

Is so what size and how are they in the snow? How many miles do you have on them? Thanks

No not for me :( I only wish. But here Dead Link Removed He even has the pics to prove it!! /me jealous

which would it be. The Edlebrock IAS or Rancho 9000's? My ranger rides like crap and I want a better ride. Which ones would you pick? I have a reg. cab shortbed 4x4. ------------------ 1994 Ford Ranger 4.0L 4x4 5spd Mods: K&N, 63mm T-body, Superchip

Right now I'm running 31's with 3.27 gears. I'd like to do a gear swap in the near future, but I'm undecided if I should got with 3.73's or 4.10's. What rpm are you guys turning at 60 with 31's and 3.73 or 4.10's? With my 3.27's I'm at about 1600 at 60. I also would like some sort of locking...