Search results

These are the parts that I've come up with so far for a refit of the original stock parts with new (shocks have been done already) ... 2-MOOG Part # K8695T Frt Susp; Lower; Problem Solver 1-MOOG Part # K8710T {Control Arm w/Ball Joint} Frt Susp; Upper; RH; Problem Solver; part of 2 piece...

2000 Explorer XLT SOHC... I saw an ebay vendor that has a front suspension kit ebay item #160448775454 for 119.00 and the parts brand is xcp...1 year warranty...anyone ever heard of this. There are three more listed with pretty much the same stuff but look more complete... #140376531937...

2000 xlt 2wd sohc 1. ABS chatter on left front at slow speeds (didn't try at greater speeds due to me not knowing the implications of ABS doing this). Removed ABS fuse (#7, 30A), not chatter, brakes work fine, ABS light lit. I cleaned the front two ABS sensors, still chatters with fuse in. I...

Ok, I thought replacing the rotors was easy from what everyone said...they came off fine, however, I notice that there is an inner wheel bearing that is pressed into the original rotor. The brembo replacement rotors do not have this bearing pressed into it. How do I get that out of the original...

Probably a dumb question...If one is changing the rear rotors, does the parking brake on both sides need to be removed or does the rotor just come off after removing the caliper?

Ok, 2000 xlt sohc...new plugs and wires...starts normally most of the time, but occasionally the truck starts and will only stay running if I stay on the gas...if I rev high during this condition it sounds like one of the cylinders isn't firing (dunno)...get off the gas and it dies. Sometimes...

I've decided on the Brembo rotors from tirerack since they are within my budget (powerslots are a bit beyond my reach). So, I would like to try the Hawk pads that I see everyone recommending, but which exact Hawk pad should I get?

I'm getting an intermittant scrapping noise from my right side brake...I think its in the rear. I had the same thing on the left rear a year or two ago, shop told me they "had to take the caliper apart and adjust it". When I apply the brakes the noise stops but eventually comes back. Any ideas?

Ok, I took a caliper and put it on a couple spots in the center of the front sway bar...it read 31mm...there is no bushing that is 31mm...choices are 27mm, 29mm, 34mm. Is there somewhere else I can measure this or possibly call ford and give them my vin# for them to tell me?

First off, thanks Gavin for your insight on my previous question (I've decided to go with the mevotech uppers) this is kind of a continuation of that thread. I've seen some of you say that sometimes the aftermarket lbj's don't fit into the stock arm. I'm concerned about this. I would much...

I just ran across one of the vendors on this site, RockAuto. I saw they have several different types of UCA's w/ bushings...the Raybestos are the cheapest, then Dorman (which says OE) and on up. I'm on a tight budget and was wondering how the Raybestos arms hold up. Heres a link to the RockAuto...

Ok, this one is hard for me to describe...its a noise coming from my right front when I go over a bump that gives the suspension a decent amount of deflection. Kinda a low pitched squeak on the down stroke and up stroke...almost like you'd here from a mattress...lol...get your minds outta the...

I see in a lot of threads to go with the amsoil...is there any particular type of amsoil or is it just their atf? And el cajon, ca people that use amsoil; where did you buy it? I have 96k miles on my '00 xlt 4.0 sohc, I've heard some say that you shouldn't flush at this much mileage...

These are the plugs with 2 electrodes that do not require gapping...are these any good or should I return them and get the autolite double platinum (app103) or the autolite single platinum (ap103)? Also, I think I bought the bosch OE wires...dump them as well? What would be the best wires? (Its...

I'm replacing all 5 shocks today and need to know if there are specific torque values for the nuts/bolts on them. Thanks for the help. (4.0 sohc)

Just wanted to say hello and say I'm damn happy I stumbled upon this forum in a google search. I was up late the other night browsing the site and I could have sworn I saw a link in a thread for a service manual iso (I have a 2000 Explorer 4.0L SOHC). It would be greatly appreciated if someone...