Search results

Guys, I need the part number of the speed sensor pictured here (the one mounted on the bracket on top of the tone ring) that produces a type of signal similar to that of the ford oem one that does not need conversion (via the ABS/ECU) to be used for a digital speedometer. I got the...

I keep reading about this "o-ring" part when you replace the gasket on your thermostat housing but I can't find it in any parts catalog. There's this small leak that's developing under the thermostat housing, that is common on our trucks, that I went ahead and ordered a new gasket and...

After I accidentally damaged one of the Taylor 8mm Spiro-Pro wires leaving me with a backfiring engine and lousy idle below 2000 rpm, I then decided to give MSD's 8.5mm Super Conductor Wire set a try. These MSD wires are advertised to have less than 50 ohms per foot of wire and after...

What would be the ideal drive line angle for the front differential relative to the 4406 transfer case? Diagrams are welcome :thumbsup:

Anybody here have one lying around that they want to get rid of? :) talking about this guy: I prefer aluminum covers that can aid in transferring heat out of the diff fluid and don't need heavy duty cast steel ones. I'm hoping the oem 3rd gens are a lot cheaper than the trickflow's...

There have been a few threads implying that it is safe to drive around with just the stubs of the CV shafts installed on the wheel hub assembly but none was clear about driving it normally on a daily basis, so.. Given that the following is done, -cv axles disassembled -middle shaft, boots...

I need a broken front CV shaft for the passenger side. I only need the ends, boxed in the below picture in red, which means the splines/ends must be in good condition. reply here with a shipping estimate to 90606. Thanks!! -Carl

Hey guys! I need a huge favor.. Can somebody post a picture of the back circuitry of the oem 3 button/4 button ford fob remote? the negative battery tabs on mine fell off and i cannot find where it was attached before. Thanks!!! -Carl

is it possible to replace the drive gear on the transfer case shaft to correct the speedo after a 4406 swap? i have the red drive gear (21 tooth) on the vss and the stock brown one on the 4406 and it reads about 4-5 mph over the true speed and that is the closest i can get it to since the red...

Windows couldn't find/install the drivers for my SCT x3 and I cant find the tune loader software at the SCT website. Shipping this thing to and from the tuner to get a new tune is getting ridiculous. btw, i can't find my envelope that contains the x3 manual and installation disk.. the user...

I have this ticking sound that mimics an exhaust leak that increases with engine speed which is also noticeable under load that I cannot figure out the source. Here is what I know: What it is NOT: - Not an exhaust leak (Remflex gaskets on Torque Monster Headers, no leaks on any flanges) - Not...

So I have this AWD drivetrain (AWD Tcase, Front and Rear D-shafts) sitting in my backyard and I have no idea where I can sell it at a reasonable amount. Do i go talk to driveshaft/tranny shops or junk yards? what would be a better place to get more dime out of them?

Has anybody noticed how much creaking and noise the rear hatch makes whenever you turn up/out of a curb or a small incline or when you take a turn a bit faster than normal? every time I pull in/out of my driveway that darn hatch creaks like crazy. Initially, i though that the whole truck was...

Is it possible for a bad rear axle bearing to squeak when it goes bad? There's this "squeak.. squeak.. squeak.." rotational noise that i'm getting from the rear passenger side wheel area when moving slowly up to 20mph and it mutes down when i press the brakes. It also syncs with the speed i'm...

Hi guys! So I completed the 4406 swap this past Saturday and everything went smoothly. Test drove her around the block and did a couple of quick burnouts (that alone made the swap worth the while :D) and so far everything feels fine and the drive feels lighter and more solid. Today, I was...

Hi! Does anybody here know if I should change the gear on the vss on my 4406? It has a 19 tooth gear installed on it and I have stock size tires with no plans of up-sizing anytime soon. The gps speed accuracy test will be done tomorrow and i'll bump this up again by then. TIA, -Carl

Hi guys! I'm looking for a good and functional used set of the shifter assembly and linkage that bolts to the transmission and pops on to the 4406 tcase. Here's the Shifter and Linkage (part numbers: F65Z7210BC and XL3Z7B051AA) For some reason I could not post a wanted thread in the...

this may sound silly to you guys but i really have no idea which is the front and which one goes to the tcase since both flanges fit on the 4406. plus how the conversion u-joint is oriented with the driveshaft. Which one goes to the 4406 and which one goes to the d35 in the front? A or B...

Hey guys! I'm not sure if the governor in my 4R70W is sticking or not but heres the scenario: The trans would not shift to the next gear sometimes and i would need to either let it rev to around 4500-5000 rpm to shift and let off on the gas. It would do this in all of the gears from 1st to...

I've read all the threads i can find related to the swap and can readily find information on the parts and their corresponding part numbers if ever i do get to do this myself. But, i still need to justify if it would be worth my while. In my case, my truck is a 97 V8 AWD and currently is...