Search results | Ford Explorer Forums - Serious Explorations

  • Register Today It's free!

Search results

  1. T

    Replace Head Gasket or more? 2000 Explorer - first timer

    Tools If you considering it as an Investment i would Buy a good air compressor and air impact, electric impacts are good under certain circumstances. The more Air Pressure = more power. But different impacts are rated for specific Ranges of Air. Bigger the tank = More power without it clicking...
  2. T

    Replace Head Gasket or more? 2000 Explorer - first timer

    As dale said the 4.0 OHV is known for head/ head gaskets being blown. It does sound like the symptoms you describe does sound like a blown head gasket. Almost all the vehicles ive worked on that had bad head gaskets had. Smoked, Over heated very quickly, Loss of Power, Antifreeze smell coming...
  3. T

    KC's Timing chain thread

    Left Cassette Yeah.. Thats why i "think" its part of the left Cassette but looks different then the Left Guide cassettes i have seen. The chain on that side is still pretty Taught so im guessing the slack side broke. There is Two Pieces that im assuming came from left cassette the other...
  4. T

    KC's Timing chain thread

    Dead!?!? I was reading along.. and thread just ended lol How did everything go back together? Did it start right up? Did you Hear any timing Components at start up? I wasn't aware the balance shaft had to be timed.. But im just beginning this job, Will document and post pictures and more...
  5. T

    KC's Timing chain thread

    Dead!?!? See Photo Below
  6. T

    4.0 SOHC Timing Chain Qestions

    Most people prefer to go ahead and do as much as they can when they have to take an engine out. Water pump and thermostat is usually something you replace if its inexpensive. But i wont be replacing mine. I will be changing my tranny fluid and filter.. Engine oil and new filter is a given. I...
  7. T

    4.0 SOHC Timing Chain Qestions

    haha that looks identical to what happened with mine.. same Tensioner piece left over.. Apparently this happens too frequently Any after photos of the new guides and chains installed? Regards, Tony
  8. T

    How to: SOHC V6 Timing Chain Inspection & Repair

    You should be fine. Long as you have not loosed any of the Timing Sprocket Bolts. The Balancer is keyed it will only go on one way. Just make sure the Crank Sensor is aligned up correctly.. The old engine i took out of my 98 Explorer Had breen rubbing the Balancer.
  9. T

    How to: SOHC V6 Timing Chain Inspection & Repair

    Balancer can be removed without Timing anything, It is Keyed. Be careful with your Camshaft Sensor though. Its the one Mounted right at the Balancer. You DO NOT want to hold your Ballancer where the grooves are. The sensor uses those grooves to check location of Crank. You will need a Harmonic...
  10. T

    My thoughts on a reason to stay away from FRAM oil filters...

    Fram Xtended Guard Fram Has Learned Alot it Seems. Ive heard no bad comments or anything with using the Newer Oil Filters.
  11. T

    4.0 SOHC Timing Chain Qestions

    Which timing Kit did you purchase? (manufacturer) How does it compare to Cloyes or FORD OEM?
  12. T

    4.0 SOHC Timing Chain Qestions

    Timing Procedure? Ok so you time the jackshaft and Crankshaft with number 1 cylinder at TDC on Compression stroke.. Install all guides and sprockets with it at TDC compression stroke. Then install timing cover and balancer before you time the Cams? I will probably get a tool kit off of a...
  13. T

    4.0 SOHC Timing Chain Qestions

    Timing The back guide is still fully intact, Its still connected at the pivot.. I noticed when i rotated the engine that back timing chain got really taught. The left side is shot also that piece behind the primary tensioner is indeed a piece of the front, this is why i have not removed the...
  14. T

    4.0 SOHC Timing Chain Qestions

    Timing Chains UP Close and Personal Here is what Ive discovered.. Only question is the best way to determine if it may of jumped time? From the Haynes Manual it says at TDC. The crankshaft Key (Torque Converter Key) will be exactly straight up On Compression Stroke. So i checked that and...
  15. T

    4.0 SOHC Timing Chain Qestions

    Thank You! Thank you dale again. You have been some big help... I plan on tackling some of your mods once its up and running. Been looking at quite a few of your helpful threads.
  16. T

    4.0 SOHC Timing Chain Qestions

    Thank you Dale, How many miles have you driven on your repaired 4.0 Thus Far? Also... Ive seen some people saying the Heads must be removed to install the rear and front timing guide assembles. And from what it looked like on yours you never removed the heads. I plan on working on the engine...
  17. T

    4.0 SOHC Timing Chain Qestions

    Thank you. So ideally if im checking it out and its got Metal reinforcement it should be good long as its all intact. But if its all plastic regardless if its broken or not should just go ahead and install the updated timing components since the engine is out right now.
  18. T

    4.0 SOHC Timing Chain Qestions

    Thanks.. The Kit i was looking at is from 4USA for $151.00 Free Shipping on ebay. But what are the signs that the timing chain components have been replaced?
  19. T

    4.0 SOHC Timing Chain Qestions

    Hey guys.. been awhile since i posted about my 98 Explorer i Got. I got a replacement engine from a good Low Mileage Scrap yard... The engine looks like at one time its been gone through... But i got a scare when i started switching some components from my Locked up engine. When i pulled off...
  20. T

    Help Me!! New Here

    glad to be here
  21. T

    Help Me!! New Here

    few questions, got a buddy of mine who has a 1998 ford explorer xlt with 4.0L sohc with 145k miles on vehicle. It started clicking one day and locked up, unsure if it could be the timing chain or more extensive work. Truck is in great condition interior is clear it is a 4x4 automatic. Would $500...
Back
Top