Search results

So i had bought a rebuilt transmission and about a year later the front seal leaks and all my transmission fluid dumped out so about 3 weeks ago, i took the transmission out replaced the front seal and torque converter and put it all back together made sure my fluid is at the proper level and it...

does anyone have any step by step instructions to removaling it, i cant figure out if i have to removal the heat shield along with the exhaust and my haynes manual doesnt say anything? its a 1993 explorer

i opened the hood up and there was gas leaking on the driver side exhaust manifold and i noticed that there was gas spitting out of my exhaust pipe and out of the whole in my muffler, i thought that maybe one of my injectors was stuck up and and it was dirty so i had all 6 cleaned and tested...

i ran some trouble codes on my 1992 explorer and i got a code 513,114 and 116, i looked up a 513 and it says pcm internal voltage failure does that mean i need a new one? and also my explorers fuel injectors seems to be putting out a rich mixture of fuel. i pulled all spark plugs and checked...

i has just filled my tank with gas and its a hot day ive been having problems with coolant usage and i was driving up a steep hill and i noticed my temperature gage was pretty high and as i was pulling into my driveway i went over a speed bump and it slipped and wouldnt go anywhere then kicked...

im wanting to paint the chrome grille i have right now flat black but im having a hard time sanding the chrome off, it doesnt seem like im getting any where is there anything better i can use to get it off

i have 1992 eddie bauer explorer 4x4 with a a4ld transmission and was wondering if the transfer case takes a certain fluid or if you can use normal atf like i would use for the transmission and how much do i put in?

i rebuilt the valve body did everything and i put the transmission fluid in at first i didnt put enough and it wouldnt go anywhere now i put more in and it drives but it still does the same thing it did before and a little worse, which i had no or delayed reverse, now i have none, and it would...

i just rebuilt my valve body and i put it in i put 3 quarts of fluid in and went to put in into drive and it wouldnt go anywhere did i do the linkage wrong or do i need to put more fluid in and if so how much?

i took out the valve body and rebuilt it but didnt see the little filter that is retained on the seperator plate, i checked everywhere but i dont think it had one, do you need that filter?

am i able to do this without having to take out the full transmission or can i get to it by dropping the pan?

how hard is it to rebuild a A4LD transmission, is there any special tools you need to buy and how long would it take with a rebuild kit?

is my transmission going out? it has a hard time reversing you have to sit in reverse gear and put in the gas a little till it grabs and when im in drive or overdrive the rpms are really high its almost into the red line when im going about 55. if i have to replace the transmission what...

How do you remove a center console for this year does anyone have any pictures and steps on doing so if so that will be very helpful thanks. i wanna take it out because im designing and making my own i got bored with the one i have now and wanna add more too it.

ive had my 93 explorer automatic for a year now and since i bought it it started slipping in reverse and over the time it slowly starting to get worse and now it has a hard time going anywhere in reverse you gotta get out and push the car to help it, and its slipping in drive but its only like...

This is my first time doing Brake work, and i took off the rotors and on the back of the driver side of it had a gear looking thing attached to the back of the rotor but the passenger side did, now i bought new rotors but now both of the new ones do, are they suppose to have those? what are they...

i had just put a new engine in my 1993 ford explorer got it all together and everything plugged in and when it comes time to start it, it takes awhile but when i finally starts ir runs for a few seconds and a flame came outta my driver side exhaust manifold, why? what would cause that