Search results

Check this out! lol...is there even an engine??!!!?? :eek::eek::eek::eek: 8 7.2” TV’s 57 2.5” TV’s 13” Sharp TV 2 7” Headrest TV’s 10 7” TV’s 7 4” TV’s 1 17” TV 17” Samsung screen...

Plan on buying 4 10" midrange speakers in the next week. Would the C Pillars hold up 2 speakers each? Maybe fiberglass it? What would it take for these pillars to hold? What are your thoughts/suggestions? Arrows pointing to the pillars in the rear, closest to the liftgate TIA PPLES!

Can anyone point me to a thread that goes through the steps of removing all the trimming from the ex? Searched to no avail. I have trimming on bumpers, fenders, quarters and all doors. I might be buying a parts explorer in the next month and will be taking off bumpers, doors, hood, etc. The...

Anyone done it? Below are the specs I found, wondering would i have to buy spacers or would they even fit? 02' XLT: BOLT PATTERN: 5x114.3 (5x4.5) STUD SIZE: 1/2"x20mm HUB / CENTER BORE: 70.6mm OFFSET: 25-40mm (M/H) Camaro 2010-2013 Size: 20" x 8", 5x120.7 (5x4.75) +35mm offset...

Hey, got a remote starter in, just need to bypass PATS. I only have 1 key and I need a 2nd to program the bypass, which costs $100 @ dealership. I found this usb module that only needs one key and a pc, but it can only be a 40 bit key to work...

Can this be done? I see on the back of the ebay controller pic, there's two plugs. Not sure about mine. Would this be a direct swap or would additional harness be required? Will need a new dash as well. TIA :) Ebay...

Hey everyone, I already did a search and read a couple posts regarding this issue. Just wanted to get a quick answer as why this happened. The side plastic from the intake manifold cracked. The hole is about 3" x 1.5". Wondering why this happened and would this show some kind of...

Hey everyone, wondering why my auto-lamps (low beams) are always on, started about a month ago. When in the auto position, always stays on. When on off position, stays off. Other 2 modes work fine too. no matter what time of day, low beams are always on. Disconnected battery and reconnected...

HAPPY NEW YEARS to the Ex family!!! This thread was created to see if I made the right connections, but also can be as a tutorial of where to make the connections on your Ex when the diagram is corrected. As a Christmas present from my wife, I ordered a AutoPage C3-RS-665 and a iDataLink...

I just recently replaced my 4.6l engine with another about 2 months ago. The problem with the old one is just the Tensioner arms/timing chain which caused a knocking sound. The engine had 123k so i decided to replace with another (new engine has 80k for $800) instead of keep fixing problems as...

Hi All...Creating this to showing all how to mod your own headlights with Halo's! {Order did get a little screwed up with the color purchase of the LED rings, but still looks good :) } :ttiwwp: First off, took me about 2 hours for first light, then 30 minutes for 2nd light...

Hey, I have two sensors that have the side plastic broken. Just wanted to know what are the names of them to buy replacements...thanks! Sensor 1: Sensor 2: Side pic of Sensor #2:

I havent seen anything on the forum about this...but I just had an engine swap about last week. Went from 02 Explorer 4.6L to 03 Mounty 4.6L. Added explorer harness to the new engine but 1 connection doesnt fit. It looks like both connectors have the same color wires. Wondering if i can...

I've seen a thread on here that has green LED Halo's within the headlights. I've already searched it up, even went on eBay for pricing. The problem is: Just for the Halo LED's (pack of 4 halos) is $199.99. I know the Explorer headlight ring is huge and and the Halo’s would make it look...

I need a little help. I have a 02 Explorer XLT 4.6L. I've already taken off all connections to engine, and last things to do is remove engine from tranny and motor mounts, etc. My question is where should I lift the engine from? There are no lifting eyes on the block, and I don't want to...