Search results | Ford Explorer Forums - Serious Explorations

  • Register Today It's free!

Search results

  1. -=DaemoN=-

    Show me your cages!

    I need some ideas. I would like to chop the whole top off the explorer. :roll: JTX - where are the pics?
  2. -=DaemoN=-

    Saab 9.3 2.0t SS

    I just bought a daily driver a week and a half ago. I was wondering if anyone knows a good bulletin board for them.
  3. -=DaemoN=-

    Test Run...

    I tested my explorer today and here are some videos. Nothing hardcore, just to see what hits and holds. :p me... 7.36mb http://home.comcast.net/~bileau21/test_run_017.mov My friend trying a line out, his first time. 9.88mb http://home.comcast.net/~bileau21/test_run_018.mov
  4. -=DaemoN=-

    Daemon's Project: Ford 9" rear end.

    I started my 9" project last week wednesday. This was an easy project but I took my time on it. It should be done this week and tested soon. Parts: -narrowed 1979 Ford 9" by 3 inches on both sides. -5.13 gears and a detroit locker. -Dutchman alloy axles -TSM disk brake conversion using...
  5. -=DaemoN=-

    Daemon's SAS

    Daemon's SAS *updated 17 July* Front: -'79 Bronco 1/2 ton HP Dana 44 -narrowed 5 3/8" on the pass side -moser alloy shaft on the passenger side, and stock shafts on the driver side. :) -CTM u-joints -5.13 gears and No-Spin Detroit -WH 5.5 coils -1.5 x .25 wall DOM steering links using...
  6. -=DaemoN=-

    cheap bumper

    I made the bumpers out of a 2x4 3/16" rec tube. It's nothing fancy but it should do it's job. I will be adding some 1.5 tube bends on the front bumper to cover up the crappy job. :p rear bumper. up close! I had to cut the frame about 1 1/2" to minimize the gap inbetween...
  7. -=DaemoN=-

    Members using 9"

    Can you tell me what you did to match the 9" yoke. If you have pics please post them. TIA
  8. -=DaemoN=-

    SQExplorer

    GOOD BUYER! I sold him my WARN manual hubs and conversion kit. He got the money out ASAP. Man of his words, definitely would do another transaction with him. :chug:
  9. -=DaemoN=-

    Another SAS in progress *pics*

    I finally had the time to do the swap. -HP D44 -5.13 and No-Spin detroit -1.25 x .25 wall DOM, 3/4" heim joints. -EB adjustable track bar. -Wildhorses 5.5 coils -big bronco upper coil buckets, cut and reinforced. -big bronco RA and stock bracket. Day 1: after 3 hours, we finished...
  10. -=DaemoN=-

    Tucson Run *pics*

    The run went well with some minor whoops, it comes with the territory right? Well, here are some of the pics taken by me and my co-pilot. :) Blaine122300 Me Becker69 Click Here for more.
  11. -=DaemoN=-

    DAEMON'S SAS Project.

    I'm not sure when I will be starting this but I'm getting all the parts ready. '79 HP D44 Front end: -shortened right side of housing -alloy axles -CTM joints -No-Spin detroit locker -5.13 gears -MM locking hubs -stock brake system '79 Ford 9" rear end: -Shortened -5.13 gears...
  12. -=DaemoN=-

    Suggestions on SAS!

    I have a '79 F-150 D44 and a matching 9". Obviously I don't wanna deal w/ shortening the axle and going fullsize. My question is should I go leafs cuz it's simple and if I do coils do I have to get a different tower, modify the RA brackets... blah blah blah? I know this subject have been...
  13. -=DaemoN=-

    8.8 or 9?

    I need your suggestions. Should I keep my 8.8 and get a detroit for it or go for a 9(w/ detroit) to match my HPD44? I wanna regear to 5.13's also, that's why I thought of swapping in a 9 and sell the 8.8. Which one would be less expensive? My project won't happen till next year after I get...
  14. -=DaemoN=-

    custom rear bumper.

    I saw this on OFF-ROAD magazine. Here's the link to their site click here. I thought somebody might be interested.
  15. -=DaemoN=-

    Chiva Falls, Tucson AZ

    Tucson folks.... A buddy and I are hiking from redington pass down to chiva falls tomorrow, saturday. After the hike we're gonna hit the trails and shoot some guns:D(depends if my other friend shows up, he's got 5). Anyways, if you wanna shoot or test your truck or hike... come and join us. PM...
  16. -=DaemoN=-

    How much is my front and rear end cost?

    How much does my front and rear end cost? If, :D I was thinking of selling both diff's how much would I get for it? Don't be shy and give me your opinion..... TTB D35 -warn manual hubs -4.56 superior gears(6 mos old) -calipers(1 yr old) -brake pads(1 yr old) cheap ones. or I can just...
  17. -=DaemoN=-

    Dana 44 carrier ?

    I found a HP dana 44 with 3.50 gear ratio and my questions is... would I need a different carrier if I replace the current gears to a lower(higher#) ratio? Thanks in advance.
  18. -=DaemoN=-

    cracked my SJ lift....

    Yesterday I was at a friend's helping him put on his new rotors. While he took off to get a tool at autozone I decided to jack up my truck and found a crack on the passenger side drop bracket. It f'in sucks!!!:frustrate I should've waited and went SAS, what a waste of money :mad: . I guess I...
  19. -=DaemoN=-

    taking out bodylift....

    I'm taking out my bodylift and wondering if someone can tell me the stock size for the bolts. Thanks in advance.
  20. -=DaemoN=-

    FINALLY!!!

    Okay, I finally got my suspension lift done. Took one pic yesterday, pics will come up soon once I finish the film and get it developed. But here's my new mods: :) -6" SkyJacker suspension, Class I(front end) w/ RS9000 -custom SOA, RS9000s mounted where the sway bar brackets was. -4.56...
  21. -=DaemoN=-

    UPDATED Before & After

    here's my trucks transformation...... stock:. Dead Link Removed after the bodylift:. Dead Link Removed Dead Link Removed fiberglass fenders:. Dead Link Removed Dead Link Removed after the paint job:. My "WANNA BE" fenderguy exploder. Dead Link Removed AMEN...
  22. -=DaemoN=-

    Daemon Nosfer's 1992 XLT

    1992 XLT 4X4 Tucson, Arizona what I have now: K&N drop-in air filter Hypertech chip high flow catalytic converter 2.5 Flowmaster Force II cat-back 3" Performance Accessories bodylift. AR767 15x8 wheels. 32x11.50 Pathfinder ATR tires...
  23. -=DaemoN=-

    VALVE COVER GASKET.

    How hard is it to change or how much would it cost for a shop to do it(just an estimate)? Thanks.
  24. -=DaemoN=-

    4x4 shops in Tucson?

    Anybody knows a 4x4 shop that will install a lift for a good price around here in Tucson? Desert Rat charges $400 if you buy the lift from them, which they charge almost double the price and I know for sure they would charge high on install if the lift wasn't from them. Also, a reputable 4x4...
  25. -=DaemoN=-

    DaemoN's BEFORE and AFTER.........

    here's my BEFORE and AFTER, not much but it's a start. :) -stock. Dead Link Removed Dead Link Removed -after 3" bodylift and 32's. Dead Link Removed Dead Link Removed that's Rick's bumper w/ winch mount it looks funny with the gap. For now it's o.k....maybe sometime I will get a...
Back
Top