Search results

Inspecting PCM pinout, there are pins with A/C wording.

Hi, Eddie Bauer 4.6 with auxiliary rear & top AC. PCM went through repair 3 years ago (different problem, that repair fixed -> assumption is that PCM repair done properly). Blend door actuators (driver & passenger) works fine, reacts to command from AC panel, no weird sounds indicating the...

So the answer - Rear wheel bearing. It was completely worn out, therefore no typical "grinding" faulty wheel bearing noise.

Thanks for the detailed explanation. It feels like there is a single significant issue causing distinctive (very harsh) side to side swaying on high speeds, that kicks in for couple of seconds every minute or so. This is why I don't think it's a case for compounded improvements from replacing...

Yes, and I also see that "rear end links and bushings and all four struts" visually look fine - not damaged like the front sway bar bushings above. Anyway, does symptoms logically look like rear end links issue?

I went to a garage, they checked, said front sway bar bushing are the issue, replaced - 0 results - the problem is not there.

Hi, Thanks y'all for the advices. So: 1. No leaking rear struts. 2. Obvious damage: haven't spotted anything. Now, 18 years old 190K miles: Obviously if meticulously judging, so (almost all) bushings are not 100% in perfect condition. And that's the point: Practically I'm not going into a full...

Hi, At high speeds after steering lane change etc. (but always occurs) it feels like something changes positions and truck starts swaying side to side and IMHO feels like coming from the rear. Then almost like that something "came back into place" and normal again. What I already did: 1. New...

Eventually I ended up buying the official repair manual from here: Do it Yourself Automotive Repair Information | ALLDATA DIY It contains genuine OEM drawings, wire diagrams and test procedures. I was overwhelmed by the procedures required for each one of the above codes-they are easy but...

Do you know which pins in the PCM are relevant? I also measured voltage at the purge valve connector and got 4V when engine on and also on key on (key off - I got 0V). So if this is a fine reference voltage at idle, it means problem in the PCM control (not signalling >4V when needed) or with the...

Hi, I've got yellow constant check engine light and after OBD2 with Forscan it appears to be simultaneously circuit fault at all 4 oxygen sensors (Bank 1 Sensors 1 & 2, Bank 2 Sensors 1 & 2) as well as the purge valve circuit. Codes are 0135, 0141, 0155, 0161, 0443. Besides the warning light...

I hoped folks here know places/workshops specialised in tuning springs per car make. --- I'm from Israel, regulations here allow suspension lift up to 2", the manufacturer must declare kit fits car model & TUV certificate (I don't know why they decided to adopt German standardisation on that)...

I'm from a foreign country where strut spacers won't pass annual vehicle inspection. I'm fine with modified springs alone (will compromise on same travel length with the original shock absorber), such that they will give 2" lift.

Hi, Since ain't series manufacturer producing suspension (coilover) lift kits part numbers for 4'th gens, I wondered maybe there are small shops & manufacturers taking custom made coilovers projects for off road lifting? Thinking about it, springs alone might be enough. Thanks in advance,

Hi, 1. Based on the pictures - looks the same. 2. Part numbers are very similar: Expedition RS999925 + RS999940 + RS999926 + RS999941 Explorer RS999924 + RS999939 + RS999927 + RS999942 3. Rancho strut type same - SS3. Since for the Explorer part numbers are discontinued and I cannot find...

Hi, Intro: Model is 4.6 V8 2006, 150K Miles Every 5K Miles oil & filter replacement: Castrol Magnatec 5w30 - warm climate Old gear issues: Transmission is regularly kicking (tried to change fluid - not helped) Generally no issues nor flashing warning lights Problem: Prominent especially on...

Hi, I'm looking for 2.5" suspension lift kits, Rancho used to have those P/N's but discontinued them. So I'm wondering if there other models I can search for available kits, and they will just fine with the 4th gen? Someone even told try Disco 3 since they sharing very similar platforms. Thanks,

Hi, Thanks. The main concern is: If it's only fitting & measuring so actually it's simple - I kind of already know what roughly will fit and then it's only small adjustments - absolutely doable. I even thinking here about 3D printing of final parts (I have such printer). The question is, and I...

Hi, Thanks. 2 small questions: 1. For the 2006, which LandCruiser snorkel fits the best? (Like for which LC model, and which snorkel brand). 2. What type of modifications will be needed? Thanks,

Hi, Does anyone know where it's possible to find a snorkel kit for 2006 4.6V8? Thanks,

Hi, unfortunately no since I'm looking for off roading ground clearance.

Hi, I'm looking for at least Spring, but better whole strut (with suspension) - in my understanding this model features a coil over configuration. [I need it for articulated off-road situations so I'm not interested in space bars - since I understood they are more for towing & loading...

Thanks! 1. Would it be possible still to find old Rancho kits with the correct part numbers? Let's say Ebay etc.? 2. What should be those part numbers? Are they Rancho internal or Ford's global? In thier website I found front kit but the lift figure was only 1" so I'm not sure if I'm looking on...

Hi, I own 2006 EB, and I'm looking for a lift kit. I'm not interested in space bars, rather at least Spring, but better whole strut (with suspension) - in my understanding this model features a coil over configuration. Now, I'm a foreigner, in my country only 2.5" lift allowed, and the kit...