Search results

I am currently replacing the clutch and slave cylinder on my 2000 sport. Its the auto2wd 4high 4low tcase. not sure what the numbers are. I plan on doing a solid axle swap in about a month and i was wondering if i could run the truck without a front d shaft? i didnt know if the transfer case...

Ive got a 2000 sport with the ohv engine with the manual 5 speed. My buddy gave me a hp dana 30 thats set up for sprung over and another d30 that has the stronger u joints. He also gave me the tierod and most all of the other components including waggy leafs( he was going to do the swap himself...

My buddy is giving me a high pinion dana 30 out of a cherokee with all the 4 link brackets hacked off set up for spring over . It has no axleshafts or bearings. Hes also giving me front yj springs with aal's, a toyota steering box out of a 92 ifs pickup, tubes to mount the shackles in the rear...

I have the ohv and ive had this issue for a while now. when i apply anymore than 3/4 throttle the floor/pedal/shifter vibrates. not too too bad but very noticeable driving. Could it be the tranny?? its a the 5 speed manual. Ive never changed the fluid....spark plugs have also never been changed...

Both my front axleshaft seals are completely gone. I am going to replace them but i am wondering if i have to drop my differential to do everything i need to do...any help at all would be great i used the search button and couldnt find anything. also how long would this take??? i am sure if i...

Should i spend the extra 100 and the "better ones" or just go with the factory replacement?? Its only been 8 months since i last replaced them. But i do wheel the piss outa my truck...What can i do to make them last longer??

I have a 2000 sport and i would like to take the doors off and do tube doors. I was wondering if they made tube doors that would fit or come close to fitting my truck. I figure it has two doors so it would probably look alright took them off. Also Is it illegal to drive without the doors and no...

pa883 4 door leafs aals shackles 33x12.5 dunlop mud rovers stock 4.10s 5 speed just need to do rear bumper brackets and gap guards...ill get some wheeling pics soon. hopefully these pics work

Ive done some searching and couldnt seem to find what i was looking for...i was wondering if there was a limit for which i could crank my torsion bars and align it without the camber kit...I know its different for most but I was just wondering if there was a universal limit. any info would be great.

i am trying to figure out my gear ratio. i know its supposed to be labeled inside my driver side door but both the stickers are eroded and unreadable. i have a 2000 sport ohv and its a 5 speed manual. i am trying to find this out because i am looking to do 32's or 33's in the spring after i am...

i am goin to do the buy 3 get one free deal from pro comp...Ive narrowed my choices down to the xterrains, mud terrains, and xtreme mud terrains. i plan on doin quite a bit of wheeling and i was wondering wut you guys would recomend out of these three. (they will be 33x12.50's)

i have a 2000 sport and i am in the process of puttin a 3 inch body lift in it. i am wondering if it is possible(with any amount of fender trimming) to comfortably fit 33's after. any input would be great.

the bolt could be a little wider but it seemed to do the job...some input on this would be great. and also the bolt is much too long...if i were to keep it could i cut it???

http://store.summitracing.com/partdetail.asp?autofilter=1&part=PRA%2D3700&N=700+115&autoview=sku thank you.and if it is, is this expensive???

how do you take off the assembly that conatins the wheel studs in the rear... i need to do this for two reasons. 1.my parking brake needs to be replaced(which if anyone has any info on that please chime in...and 2. i need to replace a wheel stud...Advice would be much appreciated...on a tight...

Can someone please post pics of doin their aal...i just wanna make sure mines the same...thanks

u take out the blocks or shims under the monoleaf right??

Anybody know how?? 2000 sport. Cant find and place where i could tighten it....

been looking for a while. where can i find shackles and an aal for a 00 ex. (monoleaf)

the page that tells how to do a SOA conversion...or is there one?? Ive been looking for a while now but havnt found it. any help would be great.

95-2001 No lift- 31x10.50x15 on 15x8 rim 1-2 inch suspension lift - 32x11.50x15 on 15x8 rim/ may require some extensive fender trimming 4 inch suspension – 33x12.50x15 on 15x8 rim 2 inch body lift – 32x11.50x15 on 15x8 rim 3 inch body lift – 33x12.50x15 on 15x8 rim/ may require fender...

what does it do? and would the torsion key kit for the 98-00 ranger work on a 99 ex?

where can i find a 3" spindle lift for a 99 2 door explorer? and wut exactly does it do? thanks

on a 99 sport, wut is the biggest tire i could fit comfortably?

i have a 99 explorer sport... i am hoping to make an offroad rig out of it and would like to know wut i have to do for lift to get 32's but prefferably 33's on it. i am not looking to spend a ton of money on a lift..but a fair amount. like 500. thanks