Search results

On my last flush I ran a presure test and found that I had two leaks. Now that it is getting warmer out they are starting to leak really bad. The two leaks are located at the top of the radiator right where the clips are. there are no holes, but it spits out antifreeze pretty bad. Is it...

Need some inventive advice. Some jerkoff left his chevy out of gear in my parking lot and it rolled into the back of my X. the nice part is that there is no body damage. The bad part is that when it hit my X it broke insides of the rear hatch. Anyone have any good ideas to get into the back...

I got the codes from my computer and I was wondering if you all could tell me what they are. Not sure I read them right though. here they are 116, 115, 16, 15, 6, 5. Thanks for the help

I wasn't sure weather or not to put this in the Ranger section or here. I figured it would get more eyes here. My 1997 Ranger has some weird things goig on with it. When I am driveing down the road the temp guage reads as hot as can be. When I am at idle the thing reads cold as hell. Now the odd...

Ok, yet another dumb question. I called superlift and they weren't very helpfull. What is the differance between the standard 5.5 superlift and the superrunner 5.5 lift? Do I need this? They said the standard was around $700 and the superrunner was around $1200. Is it worth it? Thanks for the help

This may be a stupid question but I have to ask. I want to install a lift myself istead of letting another bone head do it for me. I don't trust the shops here in NM. I was wondering if I put in the superlift 5.5 will I need a coil spring compresser? I am trying to figure out if I can do this...

This is just in the planning stage for now. What I was wondering is if anyone would be interested in doing a run in either Las Cruses, New Mexico or Farmington, New Mexico? I am running fairly close to stock but both areas have a ton of trails for all types of rigs. Let me know if this...

What should be the correct gap for a spark plug on a 91 Eddie Bauer? I replaced my plugs and could not find my manual. When I had pulled the plugs they were so far gone that the gap was burned to .089. I was unsure about the gap so I gapped them at .04 for now. Can anyone tell me what is...

I was looking at super lifts web site and I have searched through the message board here but didn't find an answer to my question, So here it is. I am looking to buy the superlift 5.5 suspention lift kit. On the web site it says that the package only comes with rear add-a-leafs. The leaf springs...

I just changed my shocks to the Rancho 9000's I'm not sure if I like them yet, I also have new spings aswell. The problem is that when I go around a corner it seems as if the body leans way to far. Would sway bars help this? If so how do they work? Would I have to take them off before I hit the...

I have one main objective! The only problem is that I have to do it in steps. I have a 91 EB and I want to put 33x12.5 tires on it. I know they won't fit stock. Is it posible to put a 2 inch body lift in the fit the 33x12.5 tires or do I need the lift too. I will get to the lift in a bit. Also...

Well that right I have turned the odomitor twice! Little over 200,000 miles. When can I expect the engine to fall out? Here is my problem. In the morning or late at night I have this weird thing going on with my idle. I will start my Explorer and the idle wil go from 1500 rpm to 3500 rpm up and...

In the morning or late at night I have this weird thing going on with my idle. I will start my Explorer and the idle wil go from 1500 rpm to 3500 rpm up and down until I hit the gas pedal then it returns down to about 1000 rpm. It will then run rough for a few seconds till it gets back on its...

Yes, there is lots of info on this truck. Go to the main page at http://www.explorer4x4.com and look for the featured explorers....the one you will be looking for is Todd Edgerton's '93 sport. You will also find many other Awesome Explorers! ------------------ Scott Bauer '91 Eddie Bauer

On the front drivers side the bulb for the head light had come loose. This intern melted the headlamp houseing. My problem is that the hole for which you would screw in the bulb is now about 3 inches around. In order for me to fix the light I will need the head lamp houseing. My problem is I...