Search results

Good chance I'll B goin'! I am planning on attending, and Stic-o and I can do stock runs! Stic-o, happen to have pics from the T-Haven this year? Wil

rear sensor I believe my "92 has an axle speed sensor on the rear diff. You might be able to pull this wire off to disable the RABS, but you should check with an expert first. This sensor lets the RABS know if the axle has locked up or stopped turning, then lets the pressure off to let the...

JBL help with the three dash display?!?! Help guys! Looks like you're familiar with the stock unit. For several months, when I start the '92 EB, the radio might not come on- no display or power. One or two starts later, the radio is fine. Other than that, the radio has functioned well...

X~FACTOR's error... X~FACTOR, You did make a mistake in your advice. In your signature, you said: "The next best thing to solving a problem is finding some humor in it." Well, I guess NOT!! LOL No good deed goes unpunished! I appreciated you response.

Bosch Plats Nicaraguense, I always used the Bosch Plats, work great, even w/the skinny electrode. Never mind the multi pointed things, the single gives you a consistent spark. Good luck!

thanks doug I appreciate your advice! As a matter of fact, I will prob replace all the vac lines next time I do the water lines, which is about every two years. The mileage went to crap only for about a week, but that's too long as it is. Gotta have good rubber!! thanks!

Well, Wanted to post my results after replacing various Ford parts, and I believe that I fInally solved the : *Rough idle *hard start *rich mixture *CEL *bad smell *sudden bad milage problems! I believe the FPR was the main culprit, but each item I replaced would make some small...

can this cause a rich running engine? Can probs with the canister purge system or the canister purge solenoid cause a rich running engine? Thanks, Wil

prices list - $172.72 FPN $143.36 http://www.trademotion.com/partlocator/index.cfm?action=getLocator&siteid=318&chapter=DP2025&sectionid=6&groupid=10025&subgroupid=60663&make=10&model=Explorer&year=1992&catalogid=1 Plus $16 for 2nd day delivery Good luck with the fuel line fittings, they...

code 16 might be IDM signal not received SVO, found code 16 on this Bronco link, hope it helps! Wil http://www.off-road.com/ford/bigbroncos/tech/eec/eec-iv.html

Here's the background: SVO, The VIN is:1FMDU34X0NUA97324 1992 4.0 143,000 MILES [burns no oil, but plugs had a little black carbon this time, possibly from fuel pump/pressure variation] Just changed TP, plugs, new fuel filter, cleaned MAS, replaced air filter, cleaned throtlebody...

Thanks for your info! I appreciate your responses! Mr. Shorty, I was using the Haynes as a ref. and all the codes they had listed were all two digit. It was tricky to determine which were 2 sec pauses and 4 sec separator pauses. The codes do repeat, and I would end up just writing the...

YOU NEED THIS FOR THE BEST RESULTS http://www.explorerexpress.com/catalog/catalog.html?2602

Thanks! FordSploderXLT, I sure hope it helps me too, the pump goes in this weekend! Wil

computer codes FordSploderXLT, I was looking at your post last year about error codes. I have been having almost the same codes: 53,85, etc... Did you ever find ouit what the problem was? I am having a rough idle, but I hope when I replace the fuel pump most of this will go away...

help with codes SVO, You wouldn't happen to know what the following codes are? KOEO 17, 31, 79 Running: 36, 53 [book says TPS but I just replaced it?], 85 thanks! Wil

Knowing I have to replace the fuel pump to eliminate the whine, and hopefully reduce the rough idle, I decided to pull the error codes. I used the volt meter method in the Haynes manual. [ I felt like I was using an Ovaltine spy decoder!] I ended up with error codes that were not listed in...

Good Info! Josh S. Thanks, I did order a new retaining ring. I'll be ready for this weekend! Wil

Great Ideas! Thanks to all you guys for your suggestions, sounds like a piece of cake. Good tip on the retaining ring! I do have skid plates that have been well used. Are the gas line fittings at the tank the same as the fule filter's? I will have the removal tools for them already...

grade 8 bolt from hardware store... .......I could not find another manifold bolt today ..... Limited Ex, You should be able to go to a good hardware store [not home depot] and get a grade 8 bolt with the same dimensions as the head bolt. Let us know how you do! Good Luck

FYI In the future, I recommend a technique that's worked great for me: A) Instead of an easyout, I drill the bolt as big as possible without hitting the threads B) take an ALLEN wrench, the 90Degree type, and tap it in good into the drilled hole, at least one idameter in depth C) back the...

Got the noisy fuel pump, gonna install it when it comes from FPN. I am a decent mechanic, rebuilt the LS dif, xfr case, brakes, etc... My question is: How hard is it to do, a) I know the tank should be empty b) I have the fitting tools to remove the gas lines c) what can I count on for...

BUMP Redundant, but who is driving out from OC around 6pm or so Thursday night? Brian, hope the shoulder is better, like to meet you out there.

ready, steady, GO! where and when is the driver's meeting?

I'm jealous! I have planned this trip for a year, but didn't find any one to join me. I gotta join your next trip. Even the GPS has the route mapped!