Search results

i agree 100%

I agree, common problem with sohc 4.0. Spining no start no fire, suspect the ckp (crank shaft position sensor). Now this opinion is based on you checking the light function as the post above this one explained.

at this point your best bet would be a replacement caliper, if not a new one at least replace the seal and clean it very well before reassembly. I must say i would not recommend rebuilding it yourself, it's not always so easy. advise you read online is mostly general, unique problems do happen...

Idle prob: You most likely have a vaccume leak. When you have a vaccume the pcm reads air intake volume at the Mass Air Flow, but reading o2's with a lean conditon so it trys to compensate by adding fuel ( running rich...Black residue on the plugs...) this accurance is called "fuel trim". You...

Don't re-use the lower gasket's!!! They need to be replaced and torqed to spec. To spec and in the correct order. 35 ft lbs is pretty much standard ( Not saying it's correct you need to find out to be shure) Also they have a Sequence that needs to be followed. Starting from the middle and...

The body trim is actualy black and it's not paint it's Line X beadliner, all the body trim roof rails bumpers ect are line X. The "Item" in the bezel is a cigaret lighter shaped like a piston i made into a usb power suply for my laptop. As far as the body lift, i paid way to much but i saw it at...

Now idk if you know this but your has no throttle cable, 2004 and up ex's are "Drive by wire" meaning on you accelerator peadle there is an electronic box. ectronic throttle control (ETC) replaces the cable with the etc, etc module and pcm input to controll your throttle... why? Electronic...

i traded my labor to a friend who workes for a a linex place. I took everything i wanted sprayed off and sent it out while i did the body lift, and in trade i put a supercharger on his mustang. Line X is awsome!

Yes, but first dose you scan tool read " Data" or "pids"? If it dose you can scan the "ICCM" ( Instrement Cluster Controll Module ). Assuming you get this far you can read the signal from the sender to the "ICCM" and see if the problem is in the signal to the cluster (bad sensor) or in the...

this is my sport, has a 3 in PA 883 body lift. Line X everywhere. MT wheels 33X 12.50's. Smoked lights all around....

Jeep wranglers Tj and yj bodies, jeep cherokees, rangers, explorers, crown vic's, nissan 240's, mazda pickups, and bronco II's all use the 5 on 4.5 lug pattern

I'm glad too, trying to help you figure out why you have a hard shift in second and a jolt when you turn on the cruise controll would give us all hand cramps. Good luck hope it works out well for you.

Ok, first thing you need to find where the leake is. Do you have a cooling system pressure tester? If you have not had this problem before the intake gasket install then you may have a problem with the gaskets leaking coolant into an intake runner causing the smoke, if the smoke is in fact...

take it back to the shop, if you paid them to fix it they should warranty there work. 285 sounds steep for a switch but simply they should go back on there diagnosis. if the shop told you $285 and a new switch would fix the problem they should stand by there diag and work and fix it correctly...

this could go either way, po430 is for the effiieciency of the catilist system. In the shop normal procedure would be to back pin at the pcm with an osiloscope and read what the o2 is sending to the pcm. Assuming you don't own an "O" scope i would say replace the o2 disconnect the negative batt...

The only wire that would "pulse" is the VSS, because it's an AC circuit, the flipside to taping into the VSS is, lets say you add .2 ohms of resistance to the VSS circuit by adding your gps unit in to the circuit you would be changing you vss signal to the pcm and the instrament cluster controll...

Any idea where the noise is comeing from? Is the poping out of the exaust or under the hood... the poping noise you are hearing, can only be a few things, the only way a car can backfire is when an intake valve is open as the plug is fired resulting in combustion gases being ignited while...

PCV! the pcv valve is either stuck, or you have a blockage in the recirculation system somewhere. I have seen this many times as well but in an engine that has not been run for 24 hours? idk it would have to be a large blockage to not release the crankcase gases overnight. Have you checked the...

new pics New pic's

did'nt cost me much at all the wheels and tires i had the linex was traded for labor and the tint i mixed up in the shop, so about $200.00 for the pa 883 kit, the bug shield did cost me 20.00 off e-bay though.

Ok, i had this x and the wheels and tires, i have a jeep also so the wheels and tires were laying around , i needed beadlocks on my jeep so the tires and wheels were put to the side. So i had the wheels and tried to put them on the would'nt clear so i thought i would find a way. The PA 883 body...

I have had many 4x4's and 2wd truck's, i wanted something fun to drive and keep the offroading to my jeep, my x was bought for my now ex g/f she wanted something low to the ground so i got her a 2wd, i use it to drive from work to homenow thats it really, also i had the parts and some free time

almost done 33 X 12 50 Maxxis mudder buckshots, 15 X 8 M.T. wheels, lot's of Line X, smoked heads and tails.... Now i'm trying to figure out how to make? buy some fender flares any ideas?

What year ranger and also do i order one for a 2wd or 4wd? Has anyone here done one of these? i was wondering about the steering dose the kit have a longer shaft or how is it done? I will get some pix to post.

New here and looking for some help, i have a 2002 x sport 2x4 and i can;t seem to find a lift for it. I am looking for a body lift so i can clear some bigger rubber and wider wheels. I don't off road but i backpack, kayak, and do other outdoor activities that a few inches of ground clearence...