Got 49s????

[Rx4phun]

yeah either him or Cory could make them fit. Jefe might need a bit more trimming though

 

[IAmTodd]

Jefe might need a bit more trimming though

Nah, well, maybe a little!

 

[Rx4phun]

i wonder how many feet it would take before the IFS fell apart

 

[IAmTodd]

LOL

So how wide are those, and what size rim? 20?

 

[2001ExpSport]

Those are the new Super Swamper IROK muds...very cool tire....very too big for my truck.

Sizes are 21x49x17 & 21x49x16.5

Next to it is a 19.5x44x16.5 Bogger

See prices here!

 

[Limited Ex]

$510 for 1 tire! Better start searching the couch for change......

 

[IAmTodd]

Originally posted by 2001ExpSport
Those are the new Super Swamper IROK muds...very cool tire....very too big for my truck.

Sizes are 21x49x17 & 21x49x16.5

Next to it is a 19.5x44x16.5 Bogger

See prices here!

so thats 21 inches wide on a 17 inch rim

and 19.5 inches wide on a 16.5 inch rim?

 

[xxblackxx]

you'd probably need some rockwells to handle that big/heavy of a tire combo. Then again, those would weigh more than the truck.....


I doubt anything short of atleast a D80 from a e350 or something would handle one of those.... roasting bearings would be the least of your concerns with a smaller axle.

 

[Heath]

yeah, just wait until you get the bill for the shipping too!!! Truck Freight only I'm sure... I can't imagine the UPS guy rolling those out of the back of the truck!!!

 

[JTX]

I was thinking of getting a set. How much trimming would i need with a 2 inch lift? Also what would my top speed be with those and 3.73's. LOL

 

[Rick]

Think I could fit those on some stock Explorer rims?? Maybe with a wheel spacer for clearance?? Would a torsion twist be enough lift with an add-a-leaf in the rear??

 

[IAmTodd]

Originally posted by JTX
I was thinking of getting a set. How much trimming would i need with a 2 inch lift? Also what would my top speed be with those and 3.73's. LOL

Top speed I would say would be 200mph, time it would take to go that fast, 48 hours

 

[NOTAJP]

Hey, I've got 17x10" rims. I think I could weld up a 6" body lift. I wonder if anyone makes some 32.56:1 gears?....

 

[N2MUDN91]

If i got the duff 2.5..... and a 3" body drop....... could i fit these little things ? or maybe i could tub out the rear end...........

 

[2001ExpSport]

..ignore this nothingness..

 

[2001ExpSport]

Originally posted by IAmTodd
so thats 21 inches wide on a 17 inch rim

and 19.5 inches wide on a 16.5 inch rim?

width x diameter x rim size

 

[Jefe]

Originally posted by IAmTodd
You could prolly do it on jefe's truck if he had a BL

Well, now you all know what tire I'm planning to run with my SAS. LOL

Still need to engineer the retractible step ladder to get in to my truck though

 

[Premier]

Only thing that would look even remotely good on would be an Excursion or an old school Burb.

 

[IAmTodd]

Originally posted by Premier
Only thing that would look even remotely good on would be an Excursion or an old school Burb.

Or a bus with a 4WD swap!!

 

[Rick]