Interceptor Hatch Switch/reverse cam

[Jon Diethelm]

Hi all,
New to the forum but am active on F-150 Forums. Joined here because I need FORScan help on our two interceptors we have with my volunteer fire department.

One is a 2016 with the new Hatch switch. Is there a code using FORScan to disable it so that the hatch unlocks with door locks? If this has been asked, please point me in the right direction as my searches proved futile.

Second is a 2015 Interceptor that we want to add Factory Rear View Camera to. Can get and install all hardware, need the FORScan code for activating it.

Thank you all in advance.
Jon Diethelm

 

[peterk9]

Welcome to the Forum Jon.
There is a thread on Forscan mods that have been done but I do not recall the liftgate unlock coming up in any of the posts. Not sure if you have seen it; http://www.explorerforum.com/forums...scan-update-allows-module-programming.442848/
We have a few members that seem to be well versed in Forscan and I'm sure one of them will respond to you. Good luck.
I have moved your thread to the PIU sub forum since the Interceptor may be different in some aspects than the n

Peter

 

[Jon Diethelm]

Thank you so much for your help! I did look at the FORScan spreadsheet to try and find it and there are a couple that mention the hatch but I am not sure if that is regarding the switch since it is for the 11-15's that did not have that switch. :/

 

[blob19]

This behavior is called "global lock/unlock".

 

[Jon Diethelm]

I cannot find Global Lock/Unlock on the FORScan spreadsheet, can someone assist with values for it? PlatinumOwner?

Liftgate Smart Unlock 11-15MY BCM 726-16-01 x..* zz 0=Disabled, 1=Enabled PlatinumOwner (would this work though it is a 16?)

 

[PlatinumOwner]

For the 2016 PIU here are a few options that you may want to try....


BCM
Police Rear Door Config
726-37-02 x*xx xxxx xxxx 0=Disabled(Explorer), 1=Enabled (2016 PIU Default)

Remote07 Cfg (not sure what this does)
726-37-02 xxxx x*xx xxxx 1=Glass, 2=Manual (2016 PIU Default), 3=PDL, 4=Power(Explorer), 5=Trunk

Decklid Key Switch Cfg (I think this is what you are looking for...)
726-25-01 x*xx xxxx xxxx 1=Enabled (2016 PIU Default) 0=Disabled(Explorer)

Locking Light Feedback
726-56-01 0000 0000 01xx
726-56-02 0101 0101 00xx

 

[PlatinumOwner]

Some possible configs for the 2015 PIU

APIM
7D0-01-01

0000 FC80 00xx (Stock, no camera)
4000 3F20 00xx (Ford North America Rear View Camera Present)
9000 0FC8 00xx (Ford of Europe Rear View Camera Present)

 

[stroker70]

Some possible configs for the 2015 PIU

APIM
7D0-01-01

0000 FC80 00xx (Stock, no camera)
4000 3F20 00xx (Ford North America Rear View Camera Present)
9000 0FC8 00xx (Ford of Europe Rear View Camera Present)

MY 2014 PIU has reverse camera, displayed in the rear view mirror, and at APIM 7D0-01-01 , I have 0000 8480 00DD , if this is of any help.

 

[KayGee]

Saw you posted this question elsewhere and started a thread too.

On my 2017 (should be same as 2016), I changed 726-37-02 - bit 7 goes from 1 to 0 to disable liftgate timer switch in overhead console so the liftgate would lock/unlock with doors.

My asbuilt for 726-37-02 was 0101 0202 026E and it changed to 0001 0202 026D.

 

[Jon Diethelm]

When I get the camera hardware installed I will try both options and update post. Thanks!

Will be trying to Switch inhibit for the hatch soon.