My 1992 Ford Dora the Explorer Pan-American Build | Ford Explorer Forums - Serious Explorations

  • Register Today It's free!

My 1992 Ford Dora the Explorer Pan-American Build

Hey guys, I've been lurking around on the forum for a while and finally registered to ask some tech question, and I figured I might give you a look at what I've been building/driving. I built/ing a 92 XLT to take me from San Diego, CA to Alaska, then back down as far south as it, and my bank account will go, which I'm hoping will end up being Tierra del Fuego in Argentina. Most of the guys that build overlanding trucks for these kinds of trips use Yodas or Land Rovers, but I went a different route. I hope you enjoy it. Also, if you want to follow along with my trip/truck you can check out my blog: www.turboki.com

1380424_250820555071105_167377905_n.jpg


Anyways, about 3 months ago I started my Pan-American journey from San Diego, to Fairbanks, down to Ushua (or however far the truck/bank account take me) and I'm doing it in a 1992 Ford Explorer. Now this is not your typical overlanding vehicle I know, but I've put a lot of thought and time into this build and I think it's now more than capable of doing what I want it to do.

When I first started planning my trip I had a list of criteria that a vehicle would have to satisfy:
1. It has to be 4x4
2. It has to be reliable
3. It has to be abundant throughout the Americas
4. It has to be field maintainable
5. It has to get reasonable milage
6. The overall budget (vehicle + equipment + repair + mods) would be under 15k
 



Join the Elite Explorers for $20 each year or try it out for $5 a month.

Elite Explorer members see no advertisements, no banner ads, no double underlined links,.
Add an avatar, upload photo attachments, and more!
.





That last one really limited me. I know a lot of you spend that much just on lighting, but I wanted to quit my job, and travel as long as possible so I limited my budget. In my garage I had an 07 Honda Fit and a 65 Chevy C10 so I had nothing lying around I could use, so I went on a hunt. Right off the bat I started looking at Yodas, Rovers and Mitsus, but all of these had issues. In the Yoda category my only real option was the second gen 4Runner, but those trucks are tragically under powered and ridiculously complicated to work on. Land Rovers were a similar story. Most of my budget would go to just the base vehicle without making it bullet proof. There were a few Mitsus and Datsuns, but nothing really caught my eye. I was hoping to find a nice FJ60 with minimal rust under 5k, but that was proving close to impossible, and then a poor, abused little 92 Explorer XLT dropped into my lap.

IMG_1725.jpg


This truck belonged to my buddy Will, who has had for almost 20 years and has used it thoroughly, but it was free. This meant that I could dedicate the bulk of my 15k towards rebuilding the whole thing exactly to my spec, and in the process I'd learn everything about it. At first I thought this would be a 5k build total, but the reality is rarely that generous, and so far I've been almost exactly on the 15k budget. It did, however kind of hit all of my selling points. It's 4x4, has the german built OHV 4.0L V6 that will run on 2 cyl if it needs to, it's simple as can be, shares most parts with the Ranger, both of which litter every nook and cranny from here to Argentina, is way more torquey than the other trucks I was looking at (ehm 4runner) and surprisingly gets 14-15mph. In terms of modern trucks this sucks, but for the price range, this is actually pretty decent.

The first impressions driving it home, however, were a little scary. It ran really rough, what was left of the tires felt like they were made of chunky peanut butter, the breaks did not exist and 3rd gear synchro was no longer in the gearbox. It was also covered in a very fine layer dust and dog hair, inside and out. But, it made it back to my garage and I get to work on it. The first step was to do the basics. Oil change, spark plugs and wires, all filters. I also started the tear down of the interior to clean it out. My surprise when I found a nice layer of gravel. Every latch, spring and joint were seized with dust and hair. Turns out my buddy Will used to shovel gravel/dirt/yard trimmings/etc whenever he needed to haul something. I think however that the gravel may have spared the floor from rusting, so not all bad news.

IMG_1661.jpg


IMG_1663.jpg


IMG_1662.jpg
 






After an initial cleanup, I turned to debugging the motor issues. There were no codes being thrown, and the motor ran really smooth and strong with gas, but on idle it sputtered. It also smelled like crap and I knew there was no way it would pass smog. After running a series of tests I found that the compression in one cylinder was low, and that it was the head to blame. So I tore into the motor.

IMG_1734.jpg

IMG_1761.jpg

IMG_1763.jpg

IMG_1771.jpg
 






What I found was that one valve was bent and had been for a while. The intake was totally caked in soot. The heads made their way to the machine shop and I got on the problem of bad accessories. I swapped out the PS pump, cleaned up the alternator and determined the AC pump was totally shot, so I disconnected it, for good measure. I also saw how rusted the water was in the motor so I flushed and replaced the radiator, lines and thermostat. Well, the news was a little worse than I thought. The bent valve was just the start of the problem. The head was actually cracked at the valve so there was no way to repair it. Instead I had to get a whole new head, but luckily, these things are pretty cheap so $400 later I had a nice new top end. Surprisingly, this made the truck actually pass smog on the first run and I got new plates and registration shortly there after. The next phase was fabrication. I wanted a front bumper with a hitch receiver and skid plate, rear bumper with a 6th tire and jerry can mounts and a safari rack with 4 roof top lights.

IMG_1978.jpg

IMG_1977.jpg

IMG_1973.jpg

IMG_1975.jpg
 






The fabrication looked good, but the guy doing the work for me screwed me and did not deliver what I paid for. The front bumper and the rack both came out good, but the rear bumper did not have any mounts. I'll spare you the horror story, but 2 months of chasing him down, I was happy I got at least a complete truck back. The next step was to paint the truck and install some accessories. Being on a budget, and knowing the truck would get some abuse I opted for flat black rattle can style. I also installed 4 classic KC Daylighters and a Warn 8000 winch.

IMG_2224.jpg

IMG_2223.jpg

IMG_2222.jpg

IMG_2228.jpg

IMG_2454-960x540.jpg
 






The next step was to get some new shoes on the truck. I got 2 extra wheels from the junk yard, and picked up 6 new Yokohama Geolander tires. I also swapped out the front and rear pads. The tire shop I went to did not have what I would call the most sophisticated tools, but the tires were cheaper than anywhere else I could find.

IMG_2230.jpg

IMG_2234.jpg

IMG_2227-960x540.jpg


Now that the truck was all nice on the outside I decided to fix up the inside. I replaced most of the broken panels and switches and I also decided to rhino line the back, instead of returning the filthy carpet.

IMG_2312.jpg


I still needed to hook up the lights, so I drilled holes in the roof, ran grommets then siliconed everything in place. I also attached a layer of plastic over the wiring and waterproofed the inside of the roof, just as extra protection. I ran three switches to the front console: front inside, front outside and rear.

IMG_2321.jpg

IMG_2237.jpg

IMG_2456_2.jpg
 






I then started thinking about the electrical system. I don't need to run anything crazy in the truck, but I did want to put in a fridge, power the lights and also be able to run the winch without killing my battery. I thought about putting in a second battery, but space is a concern so I opted instead for a high gauge wiring upgrade and a HO alternator. I ended up getting a 225 amp from Mr. Alternator (great amp btw) and installing 0 gauge wire. Initially I went with CCA wire since it was CHEAP and 0 gauge is so over the top for the current I will be running, but it very quickly became apparent that CCA is crap of the highest caliber and I ended up rewiring everything with very expensive solid copper wire.I also added power distribution blocks in the back of the truck for the rear winch mount, 12v outlets and the fridge power drop. For the power source I added a 400amp fuse and a 600amp relay that switches on when the truck is on. The upside is that the entire electrical system is isolated when the truck is off, so no chance at drainage, but the fridge is off too. This is not too much of a problem as the fridge I got seals really well. Speaking of which, the fridge I bought is the Edgestar 80qt fridge freezer. It was 1/3 of the cost of the smaller ARB one but has worked flawlessly for 3 months now. It has this fast freeze option too that comes in very handy when I add fish or meat into the box. I also ended up cleaning up the factory electrical system by replacing all the fuses, stripping out an old ****ty alarm and upgrading all the ground and alternator wires to 0 gauge as well.

IMG_2344.jpg

alternator.jpg

image_2.jpeg

IMG_2448-e1366703794813-960x540.jpg

explorer_wiring.png


Next step, suspension. All new bushings, control arm and shocks. I went with budget shocks up front, but the rears I upgraded to load adjusting Monroes. I knew how much I would be hauling so the extra coilover made that shock very desirable. I was toying with the idea of lifting the truck, but I'm not planning on going anywhere too crazy and if anything broke, I would rather be closer to stock.

IMG_2393.jpg

IMG_2389.jpg

IMG_2392.jpg
 






Well, at this point the truck is running great, handles great, even had all the wiring done, but there was a problem of only having 1 spare and no extra gas, so my dad and I decided to augment the rear bumper and add the swing out. What we did was pick up a CJ bumper with a wheel mount, splice the two bumpers, and fabricate some jerry can carriers. Not the prettiest solution, but it was cheap and works really really well. We sealed it, painted it then rhino lined it for extra protection. I also decided to add some flair and added astro turf as padding in both the jerry can holders and for the back of the truck. I also added a CB antenna mount, which proved to be useless since CB radios kind of suck. I got my Ham licence since so next step is getting a proper radio.

543-960x540.jpg

380-960x540.jpg

493-960x540.jpg

494-960x540.jpg

496-960x540.jpg

500-960x540.jpg

530-960x540.jpg

528-960x540.jpg

547-960x540.jpg

543-960x540.jpg


The last thing on my agenda was to get the AC working. I replaced the entire system, no pics unfortunately. All lines, pump, etc and its now blowing cold, but the black paint made the truck heat up like crazy, so it was time to go back to rattle cans and paint the truck white...well more police.

IMG_2913-960x540.jpg


Equipment wise, the truck is sporting a Warn M8000 winch, Tepui roof top tent, Garmin Nuvi GPS, Jensen touchscreen media player, a full array of rescue and tow straps and hooks, 2 axes, shovel, hatchet, machete, hi-lift with wide base, 10 extra gallons of fuel, 6 gallons of water, a surfboard, my mountain bike, an entire array of spare parts all camping and survival gear and probably 12 other things I forgot about.

This is what the truck looks like at the moment:
946396_10201517330108587_1068338373_n.jpg

1378014_10201516556129238_792420332_n.jpg


I need to paint the hood back to black, cause the roof lights cause some crazy reflection. There were other things I've done to the truck that I have not really documented, like new speakers, entertainment, new muffler, rust repair, new windshield, new driver side rear door and tons of crap that just needed to be fixed.

The truck has so far made it up to Alaska and back down to San Diego with pretty much no issues. The only problem I've had is that it pings under load and I'm actively working on fixing it.

I've also built a storage system and bed in the back of the truck, but have not had time to get pics off my camera. As soon as I do, I'll add those as well.

Cheers!
 






Wow, what a great read!
Judging by the driveway pic, you live in either PB, OB, or maybe MB, am I right?
I've never seen jerry cans mounted like that, very interesting! What's the thinking behind that?
In one pic, it looks impossible to open the rear hatch when the tire carrier is swung out, but the next pic shows the hatch open! Is it just the angle of the pic, or how does that work?
All in all, what a great project! Looking forward to reports from the road on part 2 of your adventure!
 






Very nice Rig ! , I like Everything you have done to it , Being into car audio made me smile when I read about the HO alt and the CCA wiring being total crap lol , Love the Bumpers , Roof Rack And Really Like that Rear Swing out Tire Carrier , I also Wondered about the Operation of the rear hatch with that mounted that way , but Looks as If you have to remove the Passenger side Jerry can to open the hatch , Again Very Nice Rig and looking forward to updated pics ! ., Oh , And Welcome to The Forum ! .
 






Looks like a fun adventure rig. Keep updating this thread. I think first gen explorers make great rigs.
 






Hey guys,

Yeah, so the rear swing arm does allow the hatch to open but only if the right jerry can is removed. Yeah, its kind of a pain, but I get most of my stuff through the rear window anyways, so I don't mind taking one can off. I had to work with a bumper someone else fabricated so I was limited on options. If I could do it all over again I'd move the swingout about 6 inches further out so that the jerry can clears once open, but for the time being, its functional.

The jerry cans were initially going to be mounted on the side of the tire, but I didn't like them being exposed in case of an accident. I've seen some ARB carriers that mount the cans up above the rear tire, but I wanted to have the rear window accessible so I made them flush with the rear. I've been fabricating some more this weekend and need to finish it up tomorrow and I'll post pics.

I head down into Mexico on Wednesday so my responses might get infrequent, but if you have questions ask and I'll try my best to answer.
 






Great sounding setup. I like all the thought and hard work that you've put into it. I cant wait to hear about the rest of your trip. Keep truck'in!
 






Great build buddy!

I like the tent on the roof as well as everything else. Do you just rest it on top of your roof rack? If so, does it distribute the weight evenly enough to not dent your roof?

Also, have fun in Mexico !
 






Back
Top