What did you do to your Ex/Mounty/RBV today?

[blueka]

Swapped over the top pulley to find out that the PAS pump was on it's way out... booked an airbag scanning for tomorrow...


Si

 

[Joe Dirt]

Put the truck back together, detailed the battery and changed the positive terminal connector on the harness.

 

[blueka]

Yesterday I drove mine for the first time.... might not seem like a big deal to some guys, but, when you consider all the effort etc I put into it, then it's a big deal... and it made me smile...


Si

 

[Turdle]

Yesterday I drove mine for the first time.... might not seem like a big deal to some guys, but, when you consider all the effort etc I put into it, then it's a big deal... and it made me smile...


Si

I bet it did!! It was a big deal I do understand.

 

[Joe Dirt]

That's cool Si- you've been hassling with that thing forever...

 

[YBCold]

got pooped on.

 

[JDraper]

Took my sunglasses out of it...

 

[Varsity]

Working on replacing a lower intake gasket.

 

[Burns]

Mine was taking a bath in the rain with no doors lol

 

[Joe Dirt]

I dusted my engine...






No really- I dusted my engine.

 

[wrigley_1285]

instead of just ignoring my truck for another day i decided to fix my wiring from the switch panel i made to the roof lights. hopefully i can get it finished up tomorrow.

here's some pics of the switch panel i made. and yes the switches are at an angle instead of up and down. i also put some LEDs in the cup holders while i was making the panel and mounting my full length console. i used epoxy on the backside of the switches to make sure they were never going to move.

and since i took all the internals out of my full lenght console i removed the panel on the rear of it and put a blank in place. i'm probably going to paint a ford logo on it. i also put a LED over the rear cup holders

 

[LONO100]

replaced a broken tire valve stem.

 

[sport97]

Cleaned the engine bay. That was the last thing to complete my full detail job.

Wrigley, I like the switches. That is where mine are going to be put...whenever I actually get around to it.

 

[Paraphoe]

 

[wrigley_1285]

Cleaned the engine bay. That was the last thing to complete my full detail job.

Wrigley, I like the switches. That is where mine are going to be put...whenever I actually get around to it.

it was pretty easy to do. all it took was some switches i bought in bulk off ebay, a thin sheet of metal i cut and bent up and some epoxy to hold everything together.

Paraphoe - my console sat outside for a while and then it sat in my garage even longer. plus it came out of an ex with no windows or doors that had been sitting in the scrap yard

 

[Paraphoe]

Paraphoe - my console sat outside for a while and then it sat in my garage even longer. plus it came out of an ex with no windows or doors that had been sitting in the scrap yard
=

Just busting your balls, brother. I was bored at work.

Really like the switch panel. I guess it's too late, but it would look awesome powder-coated in crinkle-black. Nice work regardless.

 

[wrigley_1285]

Just busting your balls, brother. I was bored at work.

Really like the switch panel. I guess it's too late, but it would look awesome powder-coated in crinkle-black. Nice work regardless.

it's cool buddy. i had actually thought about getting some crinkle or hammered spray paint but i just decided to use the black engine paint i had in my chemical locker

 

[gmanpaint]

Wrigley, I had used those type switches once. They got so hot after being on for a little while, they would not shut off. I ended up replacing them all with a paddle style. Hopefully you attached them in a way that the switch itself can be replaced if this happens to you.

Things done to the 94 this past week....
Installed a set of Eddie Bauer Leather seats
Installed a sever duty fan clutch
Ran new wires on the rock lights

The "to do" list is growing......ack!

 

[tantrac]

I got the oil changed, washed and waxed the truck, and detailed the interior a bit.

 

[wrigley_1285]

Wrigley, I had used those type switches once. They got so hot after being on for a little while, they would not shut off. I ended up replacing them all with a paddle style. Hopefully you attached them in a way that the switch itself can be replaced if this happens to you.

if i ever have to replace a switch i'm gonna have to drill it out or chisel it out lol. i was trying to plan ahead by buying a bunch of matching switches but then i epoxyed them in