Whoo I love ordering parts!

exsport1211 · August 26, 2009

thegaffney said:
yeah you bet ill take some brighter pics in the afternoon, it was really easy

i was gonna ask if you think the brush guard would be ok with a winch if it was reinforced a lil. im getting the bl and the brushguard/wichmount for the 02 sport.just wanna make sure it will hold.maybe bolt on some extra support

thegaffney · August 26, 2009

here a few more pictures with the clearance and the weld, i keep forgetting to paint it, there is some surface rust, maybe ill do that today.

and some more pics after the lift and of the spindle

thegaffney · September 9, 2009

Horray mud tires !!

Oh and also im playin around with some scrap metal to figure out some sort of skid plate idea

thegaffney · September 11, 2009

yay!!

rngmStr · September 11, 2009

FINALLY

............... j/k LOL
looks great :thumbsup:

section525 · September 11, 2009

That looks great!

GRNMACHINE · September 12, 2009

Nice, those are the pics we have been waiting to see! Love those wheels/tires. Can you show close up pics of how much you had to trim behind the front tires! How is the ride?

thegaffney · September 15, 2009

here a few more pics, i wanna clean up the fender a bit for before i take more pics of that

I ordered a new magnaflow muffler today though for the new pipes im gonna get made, hopefully friday itll be here, and ordered my spare tire and rim too

Im going to go talk to a race fab shop tomorro to see about getting a sort of prerunner bumper to hold a skid plate made, that works with the push bumper being on there too to hide all the ugly stuff when the bumpers off

Fav390 · September 15, 2009

Very Very nice truck man
goodjob!!

thegaffney · September 17, 2009

heres some of the exhaust

I dont like how the bending machine bent the tubes on the end.... it like wavy where the bends are and its not very uniform, also the guy insisted on 2.5" pipe on the end even though the old was 3" and the mufflers out was 3"

I think ill go to some other place to get the last section redone, good thing is wasnt expensive, the guy has had the place for like 20 years i just figured it would of been perfect ha

and dont mind the messy tip, its a used one, my magnaflow one was too long to use at that angle, and the used one was messed up on the end, but i told the guy its fine since no one will see it, ill get a replacement new one eventually

gavin · September 17, 2009

thegaffney said:
heres some of the exhaust

I dont like how the bending machine bent the tubes on the end.... it like wavy where the bends are and its not very uniform, also the guy insisted on 2.5" pipe on the end even though the old was 3" and the mufflers out was 3"

a lot of shops don't have the capability of doing mandrel bending. I'm sure it would be a bit more expensive for the mandrel bent stuff too. It's most definitely NOT unusual for it to be "wavy and not very uniform"

thegaffney · September 17, 2009

ah i see, oh well

where here is a video of it if anyone wants to hear

I did it on my phone and my camera because they both suck and maybe you can get an idea of the sound by comparing the two haha

http://gaffney-designs.com/images/truck/Exhaust.avi

and here is the audio from the video for a smaller file size

http://gaffney-designs.com/images/truck/Exhaust.mp3

ExploreTHEWorld · September 17, 2009

Dude your truck is *****in' I absolutley love how it has evolved good luck with the exhaust, I'm planning on doing mine next week once I do my lift this weekend.

shooterdude199 · September 23, 2009

lookin real good dude. keep it nice!

diego · October 28, 2009

http://cgi.ebay.com/ebaymotors/3-Li...ptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

So these are probably the spindles you purchased right?

Why does it say FORD EXPLORER 99-03 02 01 00 2WD, I thought the set up on 2nd gens were all the same. I know you have a 00 but do you know that the difference in the setup is? I have a 1997 and if I could just pick these up then Id do that. I dont feel like spending all the money on fabtechs.
Thanks

RAF · November 23, 2009

Got a part number for this muffler by any chance?

Whoo I love ordering parts!

exsport1211

Well-Known Member

thegaffney

Active Member

thegaffney

Active Member

thegaffney

Active Member

rngmStr

Well-Known Member

section525

sextion525

GRNMACHINE

thegaffney

Active Member

Fav390

Member

thegaffney

Active Member

gavin

Explorer Addict

thegaffney

Active Member

ExploreTHEWorld

Member

shooterdude199

Well-Known Member

diego

Well-Known Member

RAF

Active Member

Explorer Features

Explorer Features

Similar threads

Featured Content