Search results

Front Trans Fluid Pump today, I am going to drop the value body. Is the front pump inside VB? I replaced the EPC solenoid with a new one. Thanks,

pressure update hooked up pressure tester to main line driver's side. zero pressure. will test epc side.

map sensor I inspected the map sensor. Is there a way to test this sensor? I took the connector off and did get an error code of P0113 on my scanner.

update zero trans fluid pressure I changed the epc solenoid and tcc solenoid. Inspected and static tested all others. Also, installed a drain plug in my pan. 10.7 ohm reading was correct for the tcc solenoid same on new one. The old epc solenoid appeared to have a small hole in the end screen...

Constant Pressure To Monitor constant pressure, the standard test port is the one.

The detailed answer is on this forum, just do a little more searching. Otherwise my quick answer is there is a test port on the drivers side above the transmission pan before the shift link. It's a little difficult to see but you should see a plug there. Regards.

thinking i thought about that but for both the epc and tcc ;the cost is less than a mercron v refill, new filter and gasket. My labor is cheap but still time spent. The four other solenoids are cheap.I know I still have to complete the refill but I would like to torque the bolts on the...

I have got a lot of information from this forum and appreciate everyone's help. Thanks! Shouldn't the resistance of the TCC solenoid be around 28 ohms. Also forgot to mention I did a visual check of the vb gasket. Appears fine. Fluid in the pan on the second drop was grey but further finger...

more investigation Today I checked all the vb solenoids Epc checked fine around 5ohms. Others checkout at 26 ohms. However the solenoid on the same line (side) as the epc but the at the other end only reads 10.5 ohms and does not have a strong click to it when 12volts is applied. All others...

The answer is on this forum, just do a little searching it's a neat fluid change that clears everything out of the torque converter. Once I get my explorer back on the ground and moving, without being pushed, I will definitely try the full clean flush. Regards,

SB Number:962410 NHTSA Number:50909 TSB Date:November 18, 1996 Date Added to File:June 17, 1997 Failing Component: Power Train:Automatic Transmission Summary: Transmission - e40d - 4r70w - 4r44e - 5r55e - new digital transmission range sensor - diagnosis service tip. I am aware of the dangers of...

I have very limited knowledge but I believe your problem is with The Transmission range sensor. I guess Michigan" Mr. DearBorn didn't notify you. TSB # 962410. I have basic information but no detailed diagram. On your vehicle do you have Manual O/D switch? I believe the TSB was to replace your...

Did not check with a pressure gauge but with everything together and full of fluid, i let the vehicle idle for about 20 minutes. I have a code reader that reads type II codes do not know if it will pick up trans codes. All codes are normal on my $60.00 reader.Can get a rebuilt trans for $1100. I...

O/D light flashing maybe bad assumption I assumed,and that's bad, that the vehicle is not able to move. If it does move and the OD lightis flashing park it and have it towed to the nearest repair station for anaylsis at least. If it does not move I know the situation you are in, towing costs...

Shops with the correct equipment can reset the codes but can not make signals ready. I am in NJ with very strict engine codes readouts as far as emissions. Check Engine lite does not even have to be on, some codes will show "Not ready" until a driving cycle is completed. Normally if you drive...

trans not engaging. Your problem is similar to mine. When you say the transmission goes though the shift gears do you mean that the shift lever can be moved to each gear. MY 2000 explorer does the same and I have no trans fluid flowing through the system at all. There is no click or actual...

2000 4.0 v6 explorer. 120,000 miles. Last Filter/Fluid change at 75,000 miles. O/D lite came on intermittently. My Son was driving the explorer and it hesitated up a hill then stopped. No previous slippage problems or anything befoe that. Fluid level was fine. Had the vehicle towed to my home...

Have always completed my own repairs since my first 1952 pymouth. Rebuilt 52 flat head six engine Rebuilt fiat engine. Installed engines in 67 volks. Replaced clutch in Datsun 410. Most other minor repairs and maintenance. Currently have 2000 ford explorer xlt with trans problem. Have...