Search results

ok, will check into that after I have done one final test attempt. and by the way thanks to all of you who assisted me with this issue and even if I don't resolve this problem in the end it is still nice to know that there are still folks out there taking their own time and energy to help a...

Disregard the 3 wire thing I was thinking that there was three but there is actually five wires on the connector I was speaking of in the photo above there are two connnectors to the left of that yellow line that reads 4x4 comp... on the Gem box. those are the two I disconected how do you...

Ok so you are sayin that the "Gem" is faulty becuase it does not light at all ? I really need to be sure of this as I understand that this is a costly item. any way to test the "Gem" ? I might think that my "Gem" might have shorted when my trans over drive burnt out "BUT" I was still able...

where might these g-straps be found? and what have they to do with the breaks or 4x4?

no I did not bench test first, as I said I simply connected the b/w and the shift motor harness from underneath without attaching the s/motor to the t/case as my wife was in the vehicle on in Nutral while she pushed the 4x4 as I observed from underneath. Yes my 4x4 worked very well prior to...

update well my dang 4x4 lights are both on again, I went out this morning to check it out and sure enough their on :mad: when they seem to come on brighter is when the break is pressed and lighter as the breaks are depressed, I do hear a click from one of the relays in the rear when I hit the...

4x4 lights are on while in 2h yeah I am going through the same exact thing to the "T" thought I was alone have not ran across any post like this yet and the help is limited and always seems to point torwards the shift motor. I went ahead and rebuilt mine (good post by the way "4X4 Shift Motor...

first I just want to thank you for your aid in the ( Won't Shift in 4-wheel. Lots of Snow!) could not have done it as confidently without your help God bless you sir. I will post my progress on that post so's not to throw things of into another direction in this post first regarding the...

same deal here Have you figured out the problem? I am having the exact same thing the thing these folks are not understanding here is that the 4x4 is engaged problem is it won't disengage, the indicator light goes out for a few seconds and then lights back on without disengaging at all during...

I have since been underneath my car with some good "ol" gray tape and placed it on my drive shafts to see if they were both turning while the 4x4 indicator light was on and they both are spinning, will it hurt my truck to drive it this way going at high speeds beyond 35mph? have to drive it this...

where goes the mark ? common you little grease monkeys any help would be nice :monkey:

where goes the mark ? MAKE A MATCHMARK BETWEEN THE GEAR HOUSING AND THE HOUSING COVER SO YOU CAN GET IT REALIGNED PROPERLY!! first sorry guys "newbie here" I am confused, where exactly does this mark on the housing and cover go? second my 4x4h indicator light stays on, I push the botton...

I have a 93 ranger 4.0 v6 working on the engine...and found this 09k92 what does this number code mean ? it's stamped on my engine base and can be seen through the right side tire well near the trans case and does it have any significance at all ? just curious

oh yeah I ended up in this forum because I was hoping to find out where I can find the engine block numbers on the block itself, cause I beleive the shop that was suposed to swap my engines only swaped my valve covers and tags, old engine 190k while the new one had only 50k miles both indentical...

I know most of us have been ripped off at least once, some of us more than we'd like to mention. but I was talking with my wife the other day after realizing we've been ripped again about who is worse or should I say better at rippin: #1 mechanic shops #2 law firms or #3 hospitals "it's a hard...

Ford 4.0 engine block serial number where is it ??? I am stupified I just can not find the dang block number I was told by the ford plant that it was near the engine mounts and could easily be seen from underneath, also the numbers I was told were not machined stamped but hand carved there...

where is the engine number located, I can't seem to find mine I'm looking for the block number that will tell me the manufacturing date of the block, not looking for the the vehicle or vin number just the engine block #'s 1993 ford 4.0

yap that's what happened alright, when I first removed the gauge I had accidently broken the little black thing that stops the needle from over spinning thus causing the eratic behavior and eventaully the overspin caused the little coil underneath the needle to tangle up and break. I went to the...

Hello everyone I own a 1991 Explorer I accidently removed the speedo core and when I put it back in the first time the dang speedo needle went balistic just spinning and spinning what the **** is going on here I thought. well I pulled out the entire cable and regreased it with grease powder...