Search results

Do a search in the forum there are many write ups on using this product. You can just dump it in your gas tank, or suck it with through intake manifold vacuum (use the hose that attaches to the pvc valve) I have not heard of any negative effect aside from fouling the spark plugs in some...

My 98 smoked an incredible amount (see write up in seafoam sticky) and then ran much better. The idle was rough after and I still had some hesitation so I inspected the plugs. They looked worn but pretty clean, I will replace them this weekend, but I cleaned and regapped then assured the plug...

Any difference between Autolite and Motocraft? I believe that both are Ford products, but I rarely see Autolite mentioned.

Pssssssss I will check this when I get home tonight. Thank you.

Anybody got a fix for this? I have the same problem on my 98 Ltd. Thanks.

Hmm, debris in the tank?, Go figure. :D

That sounds plausible as well. I would probably pursue the water/debris angle in the fuel system if your fuel level is adequate. You could try some Seafoam or similar product in your tank to remove accumulated condensation, etc. And if that doesn't work, replace the fuel filter. If it isn't one...

It's a downhill struggle Look at your fuel tank. I think the pick up is in the rear of the tank Is your tank low on fuel? Could there be water or debris in your tank? I had an experience where with a fuel tank that was low, I parked in a spot that had my nose pointing down hill that I had to...

1. Which Explorer do you own? 1998 Limited 5.0 V8 2wd 2. How much did you pay for your Explorer? 16500 01/03 3. How many miles did it have when you purchased it? 45k 4. How many miles does it have now? 125k 5. When did you obtain it? 01/03 Green with Gray leather interior, with I believe...

Seafoam OMG Yesterday I replaced my PCV and infused a can of Seafoam. I had read all of the posted accounts about the billows of smoke produced, but I (nor the people in a 2 square mile area around my home) were quite ready for this. I didn't notice the smoke as I was infusing the Seafoam due...

1. Does the ex continue to bounce after bumps? If not probably not shocks, they act as much as spring dampeners to prevent bobbing on the springs as for reducing deflection of the springs. Perhaps just a lube/replacement of the bushings if needed would solve the mystery squeak. 2. It is...

Oh just fyi I have read all of the blend door posts at least twice, but am not sure of the best, and least likely to cause problems location to cut. Thanks.

Hi all. Do we have a consensus on where the best place to cut the HVAC Plenum is? Is it better to cut the bottom (side facing the floor) if so what landmarks would you use to make your cuts? Is it the "front" the side facing the passenger compartment? Again what would you use to guide your cut...

Thank you, and, Thank you. This is a cool community.

door latch stuff My door started acting the same way, having to reach outside to the floppy handle, right before it became difficult to unlock at all. I have taken the panel off of the pass. door and can see the spring, and feel the difference between broken and not. I think I will have to...

Spring Hi I am going through the door lock and blend door fixes (plus the power antenna). I am unclear where the spring attaches on the door fix, and what the spring looks like (any ideas on sources?) Thank you. 1998 Ford Explorer 5.0 Limited

Hi,myname is Brad and I have a 1998 Explorer Ltd. I have had this for about 5 yrs (bought it with 45k now 120k) a great family car overall. I found the group through google searching a problem. Thanks for such a great resource.

Hi, while looking for info re: radiator removal I found your forum via google. I found a lot of useful info so far, and have figured out that I too have a blend door problem that I have an idea how to fix. Well that is all for now. Thanks.