Search results

This one is your issue: PCM DTC P1921 - Transmission Range Signal Transmission range also known as neutral safety switch is what tells your engine computer what gear you are in. The car will only start in park or neutral and if the signal isn't reading one of those two then your vehicle will...

It’s called 5 concentric orings with 4 weep holes with 4 moisture meters indicating which level of screwed you are at.

I don't recall having an issue when I attached a trailer. Maybe I just turned it off last time.

Not picking up what you are saying here.

Yep. Brightness is measured in lumens and the max lumens for a given wattage is like 4300-4500K. Anything below or above starts to loose lumens even if your eyes think they look "brighter".

Im thinking the same thing on the hazards. The signal delay is probably just a few milliseconds so it shouldn't affect the flash timing. Signal would just be passed through. I don't think it would act like a filter (smoothing) if that is what you are thinking. Should be able to get a connector...

I got curious on how this works and I figured it out. It's a logic based circuit. LT output = LT input AND NOT RT input RT output = RT input AND NOT LT input Brake output=LT input AND RT input

Make an adapter using a 2 to 3 wire tail light converter. See this post: Wiring US 4-Pole Trailer Connector to For Trailer with European 7-way | etrailer.com

Be nice to know what the hell is going on with the concentric vs single gaskets. Seems like the 11-12 Explorers had two orings, then during 2012 production they switch to a single piece oring. Then there was another change (unknown) for the 2016+ models.

Impact severity sensors are actually more in the engine bay behind the grille.

Bank 2 is the same head on the GTDI engine (sport) as the Ti-VCT one (NA)

Fuse 21 is for the power to the keypad microprocessor, fuse 18 powers the illumination but feeds other critical circuits. Pulling fuse 21 may work because the processor sends the signal back to the BCM to turn on the illumination. If pulling fuse 21 stops the issue then it means there is...

Yeah that's it but I don't suggest just throwing parts at it without using a scanner like Forscan to diagnose the issue. What does the instrument cluster say the outside temperature is? Is it showing correctly?

Ford Explorer Cabin Air Filter Replacement Guide - 2011 To 2015 Model Years - Picture Illustrated Automotive Maintenance DIY Instructions

Yeah that looks pretty bad.

Post a picture of the circuit board. You may bring it back by cleaning corrosion with isopropyl alchohol and tooth brush and letting it dry. Also if you have water damage make sure to clean out the sunroof drain lines as they could have clogged and caused the initial issue. You can also coat...

Scan the vehicle again and see if there are errors listed under the LTM. If you don't see any errors go to "tests" and run the "ON Demand Selft test" for the LTM (have liftgate closed when starting this). See if you get codes B236A, B2903, or B2940. I'm certain. The 2016 order guide shows on...

If the knuckle was unbolted from the lower strut then it probably did affect alignment. If only the lower ball joint was unbolted then it won't affect it. Service manual states that the lower strut bolts need to be marked where the indexes are prior to removal, this to me indicates it is...

Where the control unit is (behind the quarter panel) there is a speaker/buzzer attached to the unit and has a 2 wire connector going to it. These two wires jump right over to the main unit. Could have unplugged it and never plugged it back in.

sensor is in the hvac box accessible from under the drivers side of dash. Number 6 in diagram.

Yep, 3 wire.

They use pressure transducers now. Not an on/off switch like they were in previous generations.

What have they confirmed? When you say Limited with Ecoboost do you mean the 4 cyl one? IIRC this motor uses a variable displacement compressor so not only does it have a clutch to engine the ac compressor pulley but it has a variable solenoid that changes the compression. They need to look at...

These system are a little bit smarter than the cars of a couple of decades ago. Years ago you had a low pressure and cycling switch ran inline to the ac demand circuit. Computer really didn't have much control. Now it uses an actual sensor on the lines and evap temp sensor to make a calculation...

You also need voltage at the red/white wire as well (ignition trigger). Here are the schematics for that circuit. C912 is the connect that attaches to the overhead console and C921 should face toward the rear of the vehicle in the overhead console pocket of the headliner...

Unfortunately there isn't a sunroof module to access via the network, so no On-Demand Self Test isn't available. When you say you tested the plus/minus of the motor are you saying you saw voltage? Does the polarity reverse when the switch is reversed?

Even better. More features in the windows version including actuation/bi-directional controls (you can tell control units to do things as part of diagnostics).

Good to hear. The foot swipe feature wasn’t added until 2016 model.

The BCM controls internal current sensing transistors. After a set number of faults they a permanently disabled and require a BCM replacement. IF this is the case though they will set an internal code. May want to invest in an obd2 adapter (Obdlink MX) and an Android tablet and run Forscan. I...

Initialization procedure for both shade and glass motor (do both). WARNING Keep objects and body parts clear of the glass panel when carrying out the initialization procedure. During the initialization procedure, the glass panel closes with high force and cannot detect objects in its path...

It's possible you have a spread terminal at the connector on the BCM that leads to the RR light. You are looking at the brown/white wire on connector 2280C? Do a wiggle test. Put the connector back on, keep turn signal turned on, and try wiggling the terminal in and out, side to side. If it...

That's right.

Yeah i got the same package and it has everything. When you get that turn signal figured out, start a new thread or shoot me a message about the sunroof.

Definitely had the HID headlights from factory. I see the front park sensors for the parallel park assist which was only available on the Limited 302A package (303a if you had the 2.0 EB). These packages also had HID. If the headlights were swapped then pins had to be changed on the headlight...

Is it making a click click click sound when turning (normal sound for bad shaft) or are you getting a metallic sound when moving from a stop or going into reverse (TSB on that one), actually that TSB covers clicking while turning as well. Here is the issue:

Look above the oil cap in this video at 24:37. There are two connectors and it will be the one closest to the middle of the engine (the exposed area of the actuator is white in the video). Bank 2 is the head closest to the front.

Do you have memory seats? (Numbers 1,2,3 next to the unlock,lock button on the door) If you don't have memory then you have one of two possible issues. The switch is bad (or not making good contact inside) or the wiring from the switch to the motor is bad. Motor wouldn't be bad as it is the...

This should be the part. Note there is one for manual liftgate and one for power (power has -C and manual is -B at the end of the number. You can also look at car-part.com that searches all your local junkyards for the part. Figure out anything on the rear overhead light...

Deleted

Could you be confusing this with the recirc door opening and closing? When it opens to fresh air flow will decrease. I've noticed that I have no control over this even when switching from Auto to manual. The only way I gain 100% control is to switch to Max A/C from Auto and then hit the recir...