Search results

coolant is not getting into oil, i think it may actually be the thermo housing, although i did run into another problem. when i degreased the engine and rinsed it off i had a hard time starting it. since my battery sucks i didnt worry about it and let it sit for a minute, started it again and...

so i thought i found the leak, the temp sensor started leaking a copious amount and was very loose in the housing so 20 bucks later i thought i was done. now after a 200 mile trip my tank is empty again. someone has suggestedthe heater core but the carpet is dry does anyone know the most...

the area where the jack is, is good for a small amp. sub is under passenger cup holder for third row.

open the rear hatch, pull the top and bottom trims off, then you want to unbolt the third row seat belt, and both of the pillar trims. then unbolt the bottom seat belt mount for the 2nd row. there are two tabs on the seat bottom, push those to the side and pull the bottom cushion out. then...

i cant figure this out, everytime i fill my coolant tank it is ok for a few days, then the level wil slowly drop to about 2 inches trom the bottom and stay there. i dont see any leaks, and the truck never overheats. needle on gauge always stays just below the half mark, no matter what the...

it should my haynes lists 02-06 so you should be ok following the instructions for 04 and up. 02 03 had a different design. hope this helps

does anyone know exactly how much of a difference a tuner will make on a stock 4.0L i know a lot of people say the made a difference but i cant remember or find any hard numbers. i am all stock if it matters.

no, i think the slightly larger tire goes in the back. the reason i say that is there are 3 speed sensors, 2 front and 1 back. if the front two tires are different sizes it would be worse than the back two. i also have not had any problems, with or without auto 4X4 engaged. then again i am...

did this last week, just wired a switch and mounted in the front of the center console on the edge by my knee. looks great and works just fine. found another thing this is usefl for as well. when you blow a tire you can turn the switch off and the larger or smaller tire wont mess with the...

i have been putting off getting tires for my 03 EB for about 6 months now because i cant afford them. Anyway, we were up in the woods getting our tree and i picked up a flat, no big deal. found a level spot and changed it out for the spare. i noticed about half an inch of difference between...

or hardwire, use the connector with 3 wires for the sub, cant remember the colors, but you will need a resistor? i think or the sub will pop everytime you turn it on. run the new memory wire to the battery, and use a voltometer to find the power on lead, this allowed me to keep the radio on...

splice the ends of a rca cable in to the trucks harness, and plug it into the sub out on the deck, mine sounds very good, but then again i cut the factory connections off and hard wired the deck. if you try to use a speaker out then yeah, it sounds like crap.

thank you i will try that, i just have never had anything happen like that in my other vehicles, i appreciate that.

i managed to hook up the factory sub, but am confused because when the stereo comes on i hear a "thump" from the sub, i am not sure, i hooked up everything to the deck, any ideas

my 03 4.0 took me about 20 minutes. its a lot easier if you take the cover off the TB and remove the air intake tube. now my 91 ranger took me a about an hour and half, because of the dual plug 2.3l have to take the alt. and stuff off the driver side to get to the plugs, pass. side was...

do youhave the moulding around the wheel wells? i have the same rattle as you describe, and i believe it is a loose fastner on the moulding. i only hear it at about 40 to 45mph, 60 to 75, i dont hear it at all.

its seems to already have a tt done, i went out and measured, there is only about a a half an inch difference front to back. i am going to level it off but i dont expect a noticable difference only lifting the front a half inch. i guess i didn't research this enough before buying it. would...

i have read the threads, but it seems like everyone is always just arguing about whether a body lift would work or not. i did try searching, i just haven't found anything defintive for 02+ explorers. i guess i am just going to wait and do a custom 1" body lift when i get back to oregon, and...

my 98 used to burn the tires, even if you were rolling at 5 or 10, and i couldn't even think about accelerating going up into a parking garage. but it was two wheel drive. my 03 has the same motor and trans, v6, and 5spd auto, but wont even break free in the dirt. i want to figure out how...

has anyone thought about using a set of coil spacers? i was thinking about finding 1" spacers and getting 265/70R17 tires. i dont know much about the suspension on these rigs, but that combo should get 2 inches of lift, right? i was thinking that maybe coil spacers from a f150 or maybe a...

cavalier... front wheel drive+drift= bad unless you use the e-brake. then its 50mph donuts down an old highway.......... dont ask how i know

so i went offroad in the eddie 4.0 4wd. i think i need an inch or two above the stock height, i ended up dragging the steps a few times, but other than that it was ok, didn't get into anything seriuos but 4wd was a must on the road. my question is how do you do a torsion twist? and how much...

hi, i am the proud owner of a 03 explorer 4x4 with the 4.0l, truck is a white eddie bauer that i am working on restoring to factory condition then i will mod the motor and get it down to 7 or 8 seconds i the 0 60 run. i had a solara for a while and i want to match that.