is | Page 2 | Ford Explorer Forums

  • Register Today It's free!

is

  1. The pressure is still rising, but is stabilizing.

    The pressure is still rising, but is stabilizing.

  2. The pressure goes up when the compressor is off.

    The pressure goes up when the compressor is off.

  3. Lisle # 22800 is in use.

    Lisle # 22800 is in use.

  4. The memory saver is plugged in.

    The memory saver is plugged in.

  5. The core is reinstalled.

    The core is reinstalled.

  6. Oil is added to the compressor.

    Oil is added to the compressor.

  7. Flux paste is added before soldering.

    Flux paste is added before soldering.

  8. An old compressor is used as a vacuum pump.

    An old compressor is used as a vacuum pump.

  9. The old fuel filter is being disconnected.

    The old fuel filter is being disconnected.

  10. The new fuel filter is installed!

    The new fuel filter is installed!

  11. The old latch is being removed.

    The old latch is being removed.

  12. The new latch is installed!

    The new latch is installed!

  13. The latch is removed.

    The latch is removed.

  14. This is how the Mass Air Flow (MAF) works.

    This is how the Mass Air Flow (MAF) works.

  15. The switch is good, but the battery contacts are not.

    The switch is good, but the battery contacts are not.

  16. The motor is removed from the 14.4 volt cordless trim saw.

    The motor is removed from the 14.4 volt cordless trim saw.

  17. The motor is installed, and the saw is ready to be closed up.

    The motor is installed, and the saw is ready to be closed up.

  18. The motor is connected with 4 screws.

    The motor is connected with 4 screws.

  19. The 14.4 volt cordless trim saw is dismantled for spare parts.

    The 14.4 volt cordless trim saw is dismantled for spare parts.

  20. The lock is installed!

    The lock is installed!

  21. This is how you break off the shaft.

    This is how you break off the shaft.

  22. The lock is installed!

    The lock is installed!

  23. The hatch is open.

    The hatch is open.

  24. The hatch is closed.

    The hatch is closed.

  25. A hole is made for the locking pin.

    A hole is made for the locking pin.

  26. The aluminum tape is covering the rim.

    The aluminum tape is covering the rim.

  27. The aluminum tape is around the hemisphere.

    The aluminum tape is around the hemisphere.

  28. A bead of silicone is all around the opening.

    A bead of silicone is all around the opening.

  29. The wood top is getting connected.

    The wood top is getting connected.

  30. The wood top is connected.

    The wood top is connected.

  31. The top is cut off.

    The top is cut off.

  32. The top is covered with aluminum foil tape.

    The top is covered with aluminum foil tape.

  33. The tape is smoothed out.

    The tape is smoothed out.

  34. The tape is being applied.

    The tape is being applied.

  35. The hemisphere is used as a template.

    The hemisphere is used as a template.

  36. A Rotozip is cutting the top out.

    A Rotozip is cutting the top out.

  37. The area where the parking brake switch is located.

    The area where the parking brake switch is located.

  38. The top pin is in, and the bottom one is next.

    The top pin is in, and the bottom one is next.

  39. The piston is being pushed back into place.

    The piston is being pushed back into place.

  40. The caliper pin tool is pushing out the bolt.

    The caliper pin tool is pushing out the bolt.

Back
Top