Search results

I agree JK080. Just beyond my means as I have no hoist. I did set out and did what I could with a set of ramps. May look at buying a rebuilt transmission with all the updates or a used one at a wrecking (recycle) yard. Thank you for your help and expertize, was much appreciated. Like I...

Cleaned everything out and found some fine needle bearings. Looking at: http://www.makcotransmissionparts.com/mm5/graphics/Catalog-pdf/5R55N.pdf Could be low sprang bearing? in the reverse hub #261 again not sure.. I am going to re-assemble and put ATF fluid in and drive it till it pukes I...

I hope these pictures come in here. I took off the reverse servo and there was shrapnel and shards of steel flakes laying on the top side of it. The broken ring or spacer was laying on top as well. EDIT: no idea where it came from and what it's for? EDIT 2: The band seem to look OK, perhaps the...

OK to clarify it... Drive 1st to 5th (OD) work fine. Manual 1st works fine. Then still could be "Low/Reverse" Servo? Regards Don

I did some test last night and triple checked everything. Is the "Low/Reverse Servo" used by both forward 1st and reverse gear? If it does and my 1st gear works fine, which it does, would this not eliminate the possibility of this " Low/Reverse servo" being messed up ? I can get a "ford...

Found one of the best Service Manual Download for the 5R55W and 5R55S, thought I would share.... http://downloads.bustedfingermotorsports.com/Ford%20Transmission%20Manuals/5R55W.pdf

Thanks JK080.. This is exactly the guidance I was looking for and I thank you very much for taking the time to help me. I will do exactly as you have suggested. It may take me a bit but I will post back how it goes. Looking at this part I can see there is an internal O ring, if this has failed...

Thinking back when they did the rebuild, they were not sure what was wrong and I know they had the servo pack in and out along with the valve body more than once before realizing they forgot to drill the brass sleeve, the new ones come pre-drilled but this was 3 years ago when mine was done...

Would like to add I am not sure both Servo bores were done, I was told they were and I know for sure the OD bore was done because they forgot to drill it out and I go the bang shift from 1st to 3rd when backing off the gas and no OD... took it back in and they drilled it out.. With that being...

Problem occurred basically overnight about 2 months ago. I know one should not assume but I have concrete driveway and never a sign of a leak. Also added a few liters back a while just in case. The effect is like something is kicking fully into and out of reverse every 1/2 second, equal time in...

Hi Guys, Need some advice here. I'll keep this in point form for easier reading. Problem: Select Reverse and instantly feel a bit going in but not fully engaging. Bring up RPM and it bangs into gear then releases then bangs in gear then releases, this will continue to do this until I...

Thanks for the link. Well worth the read.

Thanks for your reply but I still find it strange.

Doesn't make sense to to have the AC compressor working when it is not needed. Total waste of HP.

Hi Guys/Gals, Not sure when this started or even if it is normal but I think not. When I select "Defrost and Lower" heat or just "Defrost" my air conditioner clutch engages and will run indefinitely. The heat selector is at the highest in both cases. Any idea's here? Thanks Don

I'm happy it all worked out for you.

Yes, that is what I was trying to put in but the filters are a pain here.. Edit: Your filtered URL looks the same as mine Edit again: To me it looks like they are all the same from 2002 to 2005

goog this Motorcraft 2002-2005 Ford Explorer Speed Sensor - Motorcraft goto 4th hit down scroll down 2/3 to "2002-2005 Ford Explorer Speed Sensor - Motorcraft"

Check out this thread, part numbers etc. http://www.explorerforum.com/forums/showthread.php?t=230878

I see it now. I think it is so that one side swings in on the top and the other on the bottom, not a mirror image but something on those grounds. I can see your point though. It's not right mixing them but realistically shouldn't make any difference once installed. Seems it would only make it...

Anyone know where there is a picture of the 4 pads anywhere handy? I Just did my rotors and pads F & B and I'm wondering what we are talking about here, (didn't save old ones). Don Edit: Mine is an 03 XLT

2003 Explorer XLT Just keeping this old thread up to date. I too had ABS light come on and off on a 2000 mile road trip. It stayed off for the past 7 months and then on for the last two weeks. Unfortunately I'm up here in Northwest Canada and we pay a premium for everything. I've read...