Search results

Maybe you could try the you know a guide or the stop that puts the wiper in the position. Maybe somehow try to get that guide up so the wiper doesn't stay on the window and not going to that Gap. And if you wanted to open the window.

If it has the premium system look on the passenger rear interior panel. And you could just look on your passenger side for your a great that will cover the sub.

Did you have the premium system with the amplifier and 8-in sub? You have to find that out first and then if it does have that there is a wiring kit to take it from the premium stock engine to your new head unit it'll bypass the rear controllers I still use the sub and amplifier but it'll work

I have a 2000 Ford explorer with the 5 l. I had to replace the actual rear window wiper motor. Pretty easy to replace the motor. Sounds like you have to hit it to make it work. Sounds like the windings are gone so the motor is gone.

Again.thank you.

Thanks alot for all that info.

And I got a quick peek where the injectors are. Looks like I have to take the whole top end off to get to it?

Thanks.

Thanks for the help.

Thanks for the help.

I have no idea how to check fuel pressure. Any help with that?

Codes came back as p0174 and p0305. Know what the code mean. What do you think this is a good first thing to do.

Coach came back as p0174 and p0305. Know what the codes mean but what do you think on the misfire cylinder? Just turn the whole thing up or do the try with the plug wire on that cylinder?

Fuel filter is new.so the front cylinder on the drivers side.what should I start with?plug wire?or just a total tuneup?

Thanks.just scanned it and p0174 and p⁰305 come up .and both come up twice.

Thanks.should of done that.i have had a few code issue in the past.

I have the 5 l V8. Did you check engine light just came on at his blinking. And the truck is running its fogging down all the time and it's just started what is it?

Ok.thank you. 7 oz

Ll if you say it sounds like tires squealing. It could either be the regulator is just a totally rusted or to season a couple areas or electric motors I'm a master electrician by trade electric motors when they get debris dust in them can kind of whine like that too so try cleaning out the motor...

You don't have to remove the window. I replaced my motor and regulator on my 2000 explorer. And if you are replacing the motor you might as well replace the regulator. You can get I got mine on Amazon for like 40 bucks for both and it was perfect. And the motor is obviously bolted to the...

Ok.i am a master Electrician and have seen a lot of motors stop working just because of dust and debri buildup around the stationary winding's and the rotor.just maybe blowing some air and cleaning electric motors could solve many issues with them.

I have a 2000 Ford explorer. With my panels it's just two screws right above the door handle latch and then clips that hold it top bottom side and it's pretty easy to get off. A lot of the clips will break but you'll see what you need to get and you can get those clips

Just saw your reply to the when it leaves free on at least the compressor oil. I did know that and did put a put it in the system oil plus the the red dye to find the leak so it it has been oiled but thank you for that

I never had that problem. But I've taken my door panels off many of times. I don't know the exact layout of the latches. But there's a lot of linkage involved and I know my driver side door lock doesn't work but I could care less about that. But I would just take a look at the linkage baby...

I had to take both my door panels off. It's actually pretty easy. I have a 2000 explorer XLT so I don't know if it's totally different but all it was is removing two screws at the actual latch on the inside and then just the clips there's a bunch of pushing clips that you know some might break...

I had that same camshaft sensor code come up about 6 months ago. And everything you just described happening to your truck was happening to mine would barely start would seem like it was running on half the cylinders and it was a mess and all I did was replace the camshaft sensor cleared the...

I had the same issue too. I just pulled the door panel and greased all the pivot points on the regulator. And actually had to clean out the top where it hits the weather stripping. And hasn't squeaked since

I have a 2000 Ford explorer xlt. My driver side motor and the regulator broke. Bought aftermarket and installed it it works fine but it is much slower up and down in the factory one on the passenger side. I think they used different amperage type motors you know how much you can pull. That's my...

There isn't enough room where they ate and sub was mounted to put a 10-in sub in. The enclosure is not big enough. If you're looking for another 8-inch box I actually am not using mine anymore I have the whole enclosuring educating sub and where the amplitz I don't know where you're located but...

You can't put a real high-end sub. There isn't enough room for a air and test it won't work with the factory with the Ford amp. What I actually did was but I bought a 8 in ported enclosure and then 8-in pile sub and still use the Ford amplifier. And it sounded a thousand percent better.

The camera issue sounds like the camera is bad.but check the camera connection and see if there isn't any moisture buildup on the camera.and the 4 ways don't have a relay.the button is the on/off and the relay.

Thank you.

Thanks

And you won't believe what I found and I know it's part of the vaccum system.its behind the drivers side wheel well.the hose from that black ball when to the intake and another hose out of the intake to this thing.i will get a pic.

Thank you.and he is on the USS Germantown.

Probably good not to upset them.my son is navy right now.thanks for your service and thanks for the info.

Ok.thank you.and what does that switch do?auto lamp means it turns your light on and off when it wants?lol.

I didn't know that the power rearview mirror wasn't plugged in.plugged it in and all my exterior lights come on and stay on.uhhhhh?

Ok.i located the ball just need to get something out of the way and it's crappy weather today.

They didn't say I just said map instead of maf and the main people I got the info from were on this site.and they were dead on right.and I didn't realize it was a v-6 until you said it.my fault.