Search results

and still looking to lift the explorer. i think i want about a 2-3" lift, nothing more. just doing some reading around, it sounds like i should go with extended radius arms to get more travel? i want to get a kit that actually works good, more travel, softer, all that good stuff, not just a...

i think i have one and i cant find it. damn vacuum leaks :mad:

is there any oem ford throttle body that i can bolt up to my 4.0 ohv? iirc my maf housing came off a crown vic. anyone ever done an upgrade like this before? or should i just go with a bbk? thanks.

when i floor the gas from a stop, it accelerates, then bogs down really hard for a couple seconds, then picks back up again and drives normally. id had some throttle response issues before, theyre gone, and it started doing this. is there a way to check the tps? thanks.

the stock front axle for a 94 explorer is a dana 35 right? trying to price some 4.10's and just want to be sure. and what kind of transfer case does it come with (and whats its low ratio?) thanks!

i used to be able to burn out in my stock 4.0 4WD Automatic 3.73 lsd explorer, but now i cant. it feels super sluggish driving around town, has horrible throttle response (i have to floor the gas about a second before i want to pull into traffic, and i feel like im gonna get rear ended). i...

so a little while back my alternator went bad, i just replaced it yesterday but the car kept dying, so i recharged battery today (tested bad so i charged it up, and it was fine), got home just fine (7 miles) today, but the battery light is still on, and the voltage on the guage is reading a...

where is a good place to get wheels and tires? i got quoted about 900 bucks at discount tire for 31x10.50-15 bfg a/t's and 15x8 steel wheels. (but i think i like the mt's better, but theyre like 25-30 more a tire, and he said they dont last as long?) thanks a bunch.

anyone ever heard of them? i know hondata makes insulated im gaskets for hondas and stuff, i was just wondering if there was anything like this for a 4.0 ohv. i felt the im after running the engine for a few minutes and it was HOT!

well did my first mod today, i disconnected the rear sway bar. i like it a lot. it doesnt feel like it rolls over much more if any, but it rides a little nicer. i think im gonna fully remove it tomorrow. just pretty excited. i also found some 31x10.50's mounted on 15x8's locally for 200 bucks...

so i was doing a 200k mile tune up on the explorer, and i cant get one of the spark plug wires off. its the very back one on the passenger side. anyone know the trick to this thing? ive already pulled the wire out of the boot (oops). thanks.

is there any high-ratio rockers available for ohv engines? just wondering. thanks.

so i got some intake cleaner from work and sprayed it on the throttle body and maf sensor, and took it around the block, and when i floor it, it jerks and bucks and doesnt gain speed, but partial throttle driving is good. also, if i go from off throttle to full throttle, it doesnt do anything...

do they fit in the stock spare tire area? it doesnt looks like theres much clearance there at all. anyone have any experience with this?

so im getting ready to lift my explorer and put on some bigger tires, and i was thinking about putting it on a rti ramp before and after just out of curiosity. where can i find one? they dont look too complicated, so i assume a lot of people have them? thanks.

would that work? i have an automatic trans, and stock 3.73's (D4 axle code on the door) i have the stock 235/75/15's on now. (i think they come out to like 28" tall) just exploring (hehe, no pun intended) different lift/tire options. thanks.

well i finally got a job and i want to buy my very own explorer. (i drive my moms now) anyway, i found this one on craigslist and it looks pretty good to me. what do you guys think? id have to get a loan from the bank because i dont have any money saved up and i have a ticket to pay off but i...

ok, so my explorer is about to tick past 200k miles, has some leaky seals, is pretty low on power, consuming a little bit of oil, etc... Im leaving for the air force in a few months and i dont want to leave my mom alone with this truck for 4 years and have something major go wrong with it...

is this a good (read: cheap) place to get oem ford parts or is there somewhere better? its 250 bucks alone for con rod bearings, 170 for rings, and i cant even figure out their methodology for categorizing main bearings. anyone know of any place that has cheaper parts? Thanks.

i have a big problem with low power at high rpm's. its an automatic, and in first gear it pulls nice till like 4k then starts to just rev and not move, then it shifts and starts pulling real nice again then starts to sputter and jerk a little bit. i think its a fuel problem since its only...

so earlier today i went and rode some trails with a couple friends and i couldnt get into 4wd, what could it be? is there a fuse for it under the dash that might be bad? (the schematic is in to owners manual and mine got stolen) what else could it be? i pushed the button, held the button, went...

So i have a 94 explorer, 4.0, and shes damn close to rolling over 200k miles. What can i do to freshen her up? is it just rebuild time now? thanks. i thought about trying some of that seafoam but i heard seafoam eats seals on higher mileage engines like mine. That "engine restore" in a can...

.

Well ive finally bought a new truck! its a 2003 Sport Trac, 2wd. I want to go the more "DUB" style with it. I dont know what size rims would look good on it. It has 16's now, but id like to throw 20's or so on it. Do you guys have any pictures of explorers with aftermarket rims? Also...