Search results

I could use a little help trying to figure out what I did wrong. I just replaced head gaskets and all the timing parts on a 97 sohc. The truck starts, runs sounds like crap at idle and wants to stall. About .007 came off each head but don't think that is an issue. I did use the Sohc tool...

I started my rebuild d-35 with d-44 outers a while ago and am ready to begin reassembling but I have 4 oil different seals in my kit and only remember removing 3. One for the rear of the pinion, one for the right axle shaft, one for the left axle shaft, but I still have one more that came with...

I am really pissed off at Accu Auto had me waiting for my 4.56 gears for two months and just sent me an e-mail saying they had to cancel my order due to a nationwide backorder of the gears. I reordered with another company they e-mailed me the next day telling me the would notify me when they...

Any one have any good ideas for creating a template to drill the holes in the rocker to install OEM runing boards?

Really great guy, I bought a set of running boards from him. He let me know when he got the money, when he sent them and even when they would arrive.

Just replaced the core support on my 91/5speed but I do not remember exactly how the wiring attach to the solenoid. I have the bat cables + red leads and the relay center in the correct spot but I'm not sure what term to attach the last wire. Thanks bil

I just got a 97 SHOC and am geting a code P0420. Also when I use the I/M monitor on my reader It says that the Cats are not ready no matter how much I drive. No drivability problems and it takes a while to come back on. Any thoughts? Thanks

I Just bought a 97 explorer and I think there is a problem with the air? When the Temp is turned all the way hot (red) and the selector is on Panel/floor the ac compressor keeps kicking on and off. The Ford tech said this is nomal operation for this truck. I do not believe him but would like...

I had a problem a few months ago and replaced alot of parts. It was titled Help Please!!!. I need to have my Ex running by Mon morning. Two days ago I started it and alll of a sudden the idle would not go down. Truck will go 40 mph by it self. I unpluged the MAF and it idles at about 1200...

4.0 Surges, Stumbles when I push the gas quick, has a slightly high idle, and has an intermitent fuel smell out the exaust. It smokes like hell + runs/smokes worst in the morning. About 55 K on engine. Just changed all the plugs, all the old look perfect. New TPS, fuel pressure reg, PCV...

Looks like most people who have done the 5.0 swap in the gen 1 use the AOD tranny. I think there are two different ones made and was wondering what one everyone is using? One has a 10.5" extention housing and the other has an 11.5. I think otherwise they are the same. Thanks

The heat shield rattle like a SOB. Has any one pulled them off completely? I was a little concerned about doing it since the front cat is so close to my t-case. I really don't want to get into welding them back on so I am open to any other ideas.

I was in Pep boys today and was thinking about replacing my motor and tranny mount since I didn't have the $ to do it when they were out and my truck has the shakes. They told me they are about $80 per side for rubber and do not list one for my tranny. 5 speed Mitsubishi or how ever you spell...

I have a grinding noise in my front wheels so I disasembled to check everything out and found that the bearings are bad again. About six months ago I replaced everything up front: Bearings,Rotors,Calipers,Brakes,Hardware,Shocks, and Tires. The spindles look fine, so the only thing I can think...

I just bought a aftermarket system of ebay but want to confirm a few things before I install it since this is the first time I've put one in. The directions I got with the kit just suck so I went to www.bulldogsecurity.com and downloaded a wiring diagram to start. All my instructions have in...

What is the least $$ of lift I need to fit 32X11.50 on my stock 91. thanks Bill

Just replaced the whole clutch system and can't get all the air out.

#1 Most important because it's coming out tonight. Dose any one know where the rubber plugs that should be replaced with metal freeze plugs in the 5 speed manual tranny are located and what size fits. #2 My dad has a nice set of 32/11.50's that he is taking off his Bronco so what is the...

I just replaced my hubs with new warns and couldn't wait to try them so the first time it rained I locked them in hit the four wheel switch and backed out of my driveway. When ever I turn the wheels the front wheels skip and the truck bucks. Never noticed this with the autos but that could be...

I am thinking of trying to to put two 8's in the rear hatch do a little sound proofing and wondered if anyone else has done this, how it sounds, and any ideas anyone else has. I already cut the box for the factory sub and replaced that with an 8", and the system sounds pretty good. Would also...