Dismiss Notice



Register Today It's free! This box will disappear once registered!

How to: Lower your explorer (pics)

Discussion in 'Seriously Lowered Explorer - Ranger Suspension Tec' started by hydroxy, January 13, 2004.

  • Searches ExplorerForum.com
    1. hydroxy

      hydroxy I like to fiddle...

      Joined:
      April 23, 2002
      Messages:
      2,306
      Likes Received:
      1
      Trophy Points:
      0
      City, State:
      Fairfax, VA
      Year, Model & Trim Level:
      1995 Limited v6
      ok I needed a garage to lower my ex, so boominXplorer was kind enough to offer up his place. I dont think there has ever been a writeup on lowering w/ lotsa pics about installing the blocks (Billions of TT threads, so I'll leave that part out). Here are pics. Ignore the crappy paint job of the sway bar.

      Whole thing took chris (boomin) and I ~3 hours. I have a limited explorer, so I have the Air Ride Control (ARC) shocks. I'll post a thread soon about controlling the ARC system... but anyways... Here is how you install the blocks. I used 2" blocks from BlackBox's explorer.


      1. take wheels off (not necessary, but highly recommended).
      2. jack up the rear end by the diff and put some stands on the FRAME as shown here. Then let down the jack to let the suspension have full sag.
      [​IMG]

      3. Take off the nuts on the U-Bolts. Then take the U-Bolts off, and move the shock mounts away from the leaf springs... IMPORTANT!!!!! on the passenger side, there is a metal bracket attached to the shock mount that holds the brake line. YOU NEED TO TAKE THIS OFF.
      [​IMG]
      [​IMG]
      [​IMG]

      4. Now you should be looking at this.
      [​IMG]
      [​IMG]


      5. Now that the rear axle is free, you need to jack the rear diff back up and put a stand HERE to make sure that the rear diff doesn't move.
      [​IMG]

      6. Put the blocks on. The hard part is lining up the little bump. but make sure that it is lined up. Then lower the axle back onto the blocks.
      [​IMG]
      Here I am reaching for the light in the middle of the photo op... whoops.
      [​IMG]


      7. I took a wire brush to the bottom shock mounts, and then I put a coat of rustoleum on them where it hits the leaf springs... not necessary but I figured I had 'em off so I might as well do it.
      [​IMG]
      [​IMG]

      8. Put the new U-Bolts on... put them right on the marks left by the old u-bolts. Getting them to line up w/ the shock mounts will take a little hammering and some elbow grease... a 2nd person is usually helpful at this point.
      [​IMG]

      9. Tighten it up as far as you can. We even used a pipe for some more torque. There are a billion and one threads, so each turn moves it up only like 1/16 an inch (think about when you're tightening) you NEED DEEP SOCKETED tools to do this... otherwise it wont work.
      [​IMG]
      [​IMG]
      [​IMG]

      Check the u-bolts in 100 miles to make sure everything is tight. There are tons of threads on lowering/raising the front via TT. Only suggestion I have for this, is to make a mark on the bolt and line it up w/ something so that you can lower each side the exact same number of turns. Once you have twisted it down a bit, push down on the front end to lower it down.

      Here is the final product (had to put these in :D )

      Before (look at gap in front wheel well):
      [​IMG]

      After:
      [​IMG]
      [​IMG]
       
      • Like Like x 1
      • Thanks Thanks x 1
    2. Support EF

      Join the Elite Explorers for $20

      Explorer Forum has probably saved you that much already, and will continue to save you money as you learn how to diagnose fix problems yourself and learn which modifications work without having to experiment on your own. Elite Explorer members see practically no ads, can add their own profile photo, upload photo attachments in all forums, and Media Gallery, create more private Conversations, and more. Join Today. Your support is greatly appreciated.


      to hide adverts.
    3. Ak LTD Xplorer

      Ak LTD Xplorer Well-Known Member

      Joined:
      December 17, 2003
      Messages:
      1,453
      Likes Received:
      0
      Trophy Points:
      0
      City, State:
      Anchorage Alaska
      Year, Model & Trim Level:
      1996 LIMITED OFF ROAD 4X4
      kinda sloppy with the red spray paint ah?

      nice write up!!
       
    4. mhn3773

      mhn3773 Well-Known Member

      Joined:
      May 29, 2003
      Messages:
      1,128
      Likes Received:
      0
      Trophy Points:
      0
      City, State:
      C.A
      Year, Model & Trim Level:
      91 zuki
      thats a great write up...before when i saw your truck i thought it was in an accident because the front seemed whiter then the back..but in daylight everything matchs 100% looks really really nice now =) and u might want to do some touch ups on the red bits =)
       
    5. hydroxy

      hydroxy I like to fiddle...

      Joined:
      April 23, 2002
      Messages:
      2,306
      Likes Received:
      1
      Trophy Points:
      0
      City, State:
      Fairfax, VA
      Year, Model & Trim Level:
      1995 Limited v6
      like I said in the beginning IGNORE THE CRAPPY SWAY BAR PAINT JOB :confused:

      I was just doing it quickly when I did it (you can't notice how bad it is unless you get close). I was planning on painting my whole underbody, but I think weather conditions will prevent me from doing it during my xmas break.

      isn't this thread suppose to be about lowering blocks? :D
       
    6. OC_Explorer

      OC_Explorer Member

      Joined:
      January 12, 2004
      Messages:
      74
      Likes Received:
      0
      Trophy Points:
      0
      City, State:
      Mission Viejo, California
      Year, Model & Trim Level:
      '92 XLT
      I normally dont like the look of lowered X's but yours looks good. Nice job
       
    7. jimbo74

      jimbo74 Elite Exploder Elite Explorer

      Joined:
      December 27, 2000
      Messages:
      18,450
      Media:
      9
      Albums:
      1
      Likes Received:
      4
      Trophy Points:
      58
      City, State:
      Nor*Cal
      Year, Model & Trim Level:
      2001, F150, XLT 4x4
      great write up... but did a blind guy paint the calipers and the swaybar? you didnt even mask anything, just like point and spray......
       
    8. hydroxy

      hydroxy I like to fiddle...

      Joined:
      April 23, 2002
      Messages:
      2,306
      Likes Received:
      1
      Trophy Points:
      0
      City, State:
      Fairfax, VA
      Year, Model & Trim Level:
      1995 Limited v6
      ha... no a lazy person did. And I did mask *some* things...

      I'm going to go over everything this summer when I paint the whole underbody. I didn't care that much what everything looked like up close when I painted it... I just wanted it to be visibile from behind.
       
    9. explorer4x493

      explorer4x493 Active Member

      Joined:
      December 9, 2001
      Messages:
      805
      Likes Received:
      0
      Trophy Points:
      0
      City, State:
      Edmond, OK
      Year, Model & Trim Level:
      2003 Limited 4x4 V8
      YUP!!! Still envious........................ :banghead: :chug:
       
    10. explorer4x493

      explorer4x493 Active Member

      Joined:
      December 9, 2001
      Messages:
      805
      Likes Received:
      0
      Trophy Points:
      0
      City, State:
      Edmond, OK
      Year, Model & Trim Level:
      2003 Limited 4x4 V8
      YUP!!! Still envious........................ :banghead: :chug:
       
    11. FXplorer

      FXplorer New Member

      Joined:
      October 5, 2004
      Messages:
      26
      Likes Received:
      0
      Trophy Points:
      0
      City, State:
      Loxahatchee, Florida
      Year, Model & Trim Level:
      '99 XLT
      How did you get the front end lowered with just adding blocks to the rear?
       
      • Thanks Thanks x 1
    12. huskyfan23

      huskyfan23 Rah no Hans Bwix

      Joined:
      November 21, 2002
      Messages:
      6,744
      Likes Received:
      0
      Trophy Points:
      0
      City, State:
      WA
      Year, Model & Trim Level:
      1994 XLT 4x4
      Torsion Twist.
       
      • Thanks Thanks x 1
    13. 2001ExpSport

      2001ExpSport Elite Explorer

      Joined:
      July 23, 2000
      Messages:
      3,368
      Likes Received:
      0
      Trophy Points:
      46
      City, State:
      Chicago, Il
      Year, Model & Trim Level:
      2001 Sport
      Those rims look sooooo much better than Cobra R's....nice!
       
    14. EBInterceptor

      EBInterceptor Well-Known Member

      Joined:
      August 24, 2001
      Messages:
      2,312
      Likes Received:
      0
      Trophy Points:
      46
      City, State:
      Ada, MI
      Year, Model & Trim Level:
      '98 Sport
      It's much easier to put line the u-bolts up with the lower shock plate if you actually remove the lower bolt from the shock. Just my thoughts about that write-up.
       
    15. gcap

      gcap New Member

      Joined:
      November 8, 2004
      Messages:
      10
      Likes Received:
      0
      Trophy Points:
      0
      City, State:
      Stamford CT
      Year, Model & Trim Level:
      1998 XLT
      After you lower you explorer like this, how does it handle? I am looking to make my 98 xlt's handling tighter. Its got about 110k on it and I have seen 2 packages that sound like they make a good combo so far. One is 400 or so, bucks for the upgraded rear swaybar and lowering blocks with edlebrock shocks from Explorer Express and the other is 400 for a front end kit from Performance Suspension Technology with all polyurethane bushings, ball joints etc... Before I blow the cash does anyone have any input. I drive mostly on asphalt but hit some dirt, gravel roads occasionally.
       
    16. hydroxy

      hydroxy I like to fiddle...

      Joined:
      April 23, 2002
      Messages:
      2,306
      Likes Received:
      1
      Trophy Points:
      0
      City, State:
      Fairfax, VA
      Year, Model & Trim Level:
      1995 Limited v6
      It handles great. I had a friend w/ a 2000 mustang driving with me one time and he said my explorer had less side-to-side sway then his mustang. Have to watch out for pot-holes though, as you can bottom out over big ones. Your offroading capabilities will be that of a car, so if you plan on going offroad, dont lower it. Gravel and dirt roads should be alright though.
       
    17. gcap

      gcap New Member

      Joined:
      November 8, 2004
      Messages:
      10
      Likes Received:
      0
      Trophy Points:
      0
      City, State:
      Stamford CT
      Year, Model & Trim Level:
      1998 XLT
      Thanks.. I will see what I can do this weekend. I think I will go with the poly bushings also.
       
    18. hydroxy

      hydroxy I like to fiddle...

      Joined:
      April 23, 2002
      Messages:
      2,306
      Likes Received:
      1
      Trophy Points:
      0
      City, State:
      Fairfax, VA
      Year, Model & Trim Level:
      1995 Limited v6
      Just thought that I'd put a little comment about lowering your explorer....

      http://www.explorerforum.com/forums/showthread.php?t=121121

      If my explorer hadn't been lowered, odds are the bumper would have hit his bumper directly and not dived under it. That probably would have saved my car from being totalled. Granted, I was at max braking so my front end would have been pushed down anyways, but since it was lowered - I think it went down a bit much.

      Think about that when you're lowering it. I will certainly lower my cars in the future, however not nearly as much as my explorer was lowered. If I do buy it back, I will most certainly raise it up atleast 1" - wheel gap be damned.

      my $.02
       
    19. warriorti

      warriorti New Member

      Joined:
      February 22, 2004
      Messages:
      49
      Likes Received:
      0
      Trophy Points:
      0
      City, State:
      Fort Carson, Colorado
      Year, Model & Trim Level:
      1995 Explorer XLT
      Your X looks great. How long did the alignment take after the drop? How much did it cost? Did you have to shim the front end?
       
    20. BauerOnDubs

      BauerOnDubs New Member

      Joined:
      June 21, 2005
      Messages:
      31
      Likes Received:
      0
      Trophy Points:
      0
      City, State:
      Natick, MA
      Year, Model & Trim Level:
      1996 Eddie Bauer
      Had me fooled, I thought they were red "racing parts".
       
    21. blk2000sport

      blk2000sport New Member

      Joined:
      November 9, 2005
      Messages:
      1
      Likes Received:
      0
      Trophy Points:
      0
      City, State:
      Lake Ridge, Va
      Year, Model & Trim Level:
      00 sport
      I see how the back is lowered, I am wondering how you did the front and if you had to have an allignment after you were done with the lowering?
       

    Share This Page







    We Support Our Troops!