CK6695
New Member
- Joined
- May 5, 2025
- Messages
- 2
- Reaction score
- 0
- City, State
- Walnutport
- Year, Model & Trim Level
- 2017 Ford Explorer Base
Good evening!
Recently Purchased a 2017 Ford Explorer Base 3.5 NA with 125k miles. Looking to fix it up but getting stumped on the issue before just “throwing” parts at it.
-Airbag Light on
-TPMS malfunction
-4wd malfunction service required
-Black radio screen
-HVAC heat stuck on - turns high once driving and cannot turn off.
I replaced the battery and tried resetting the BCM with no luck.
No visable damage to wires or signs of water entry from what I can tell.
Any help would be greatly appreciated !
Attached below were my ForSCAN results:
===PCM DTC P06E9:00-28===
Code: P06E9 - Engine Starter Performance
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Powertrain Control Module
Freeze Frame #1:
Freeze Frame #2:
-EVENT_TIME: -184447281 s (Sat Apr 26 15:39:21 2025) - Event time
-TOTAL_DISTANCE: 201874 km - Total Distance
-FUELSYS: Open Loop - Fuel System Status (Open/Closed Loop)
-LOAD: 0.00 % - Calculated Load Value
-ECT: 22 °C - Engine coolant temperature
-SHRTFT1: 0.00 % - Short term fuel trim 1
-LONGFT1: 3.91 % - Long term fuel trim 1
-SHRTFT2: 0.00 % - Short term fuel trim 2
-LONGFT2: 7.81 % - Long term fuel trim 2
-MAP: 98.0 kPa - Manifold absolute pressure sensor
-RPM: 0 1/min - Engine Revolutions Per Minute
-VSS: 0.0 km/h - Vehicle Speed
-SPARKADV: 0.00 ° - Spark Advance
-IAT: 22 °C - Intake Air Temperature
-RUNTM: 0 s - Time Since Engine Start
-EVAP_PCT: 0.00 % - Commanded Evaporative Purge
-FLI: 72.16 % - Fuel Level
-BARO: 98.0 kPa - Barometric pressure
-VPWR: 9.23 V - Control Module Voltage
-TP_REL: 5.88 % - Relative Throttle Position
-TAC_PCT: 9.41 % - Commanded Throttle Actuator Control
-RPMDSD: 1200 1/min - Desired Idle Speed RPM
-O2S12: 1.62 V - Heated Exhaust Gas Oxygen Sensor (bank 1, sensor 2)
-O2S22: 1.64 V - Heated Exhaust Gas Oxygen Sensor (bank 2, sensor 2)
-TQ_CNTRL: None Requested - Torque Control Requested
-APP_FLT: No Fault - Accelerator Pedal Position Sensor Status
-CHT_F: No Fault - Cylinder Head Temperature Sensor Status
-CHTIL: Off - Cylinder Head Temperature Indicator Lamp
-ETC_TRIM_LRN: Yes - Throttle Angle Offset has Learned
-IAT_F: No Fault - Inlet Air Temperature Sensor Status
-MISFIRE: No - Engine Misfire currently detected
-TP_F: No Fault - Throttle Position Sensor Status
-FF_LRND: No - Inferred Flex Fuel Learned
-MP_LRN: Yes - Misfire Profile Correction Learned
-MAF_F: No Fault - Mass Air Flow Sensor Status
-MAP_F: No Fault - Manifold Absolute Pressure Sensor Status
-OTS_STAT: Enabled - One-Touch Start Status
-SMC_MON: Off - Starter Motor Control Output Detected
-STRT_RLY: Disabled - Starter Motor Relay Enable
-APP1: 0.75 V - Accelerator pedal position sensor 1
-APP2: 0.38 V - Accelerator pedal position sensor 2
-TP1: 4.09 V - Throttle Position Sensor 1
-TP2: 1.24 V - Throttle Position Sensor 2
-GEAR: 1 - Gear Commanded
-GEAR_OSC: 1 - Gear Command by Output State Control
-TSS_SRC: 0 1/min - Actual Turbine Shaft Speed
-OSS_SRC: 0 1/min - Actual Output Shaft Speed
-TFT: 21 °C - Transmission Fluid Temperature
-TR: Park - Transmission range
===END PCM DTC P06E9:00-28===
===OBDII DTC None===
Successful DTC reading, no error codes found
Module: On Board Diagnostic II
===END OBDII DTC None===
===APIM DTC U0257:00-0B===
Code: U0257 - Lost Communication With Front Controls / Display Interface Module
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Accessory Protocol Interface Module
===END APIM DTC U0257:00-0B===
===APIM DTC U3003:16-08===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Accessory Protocol Interface Module
===END APIM DTC U3003:16-08===
===BdyCM DTC B124D:02-8A===
Code: B124D - Tire Pressure Sensor
Additional Fault Symptom:
- General Signal Failure
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Body Control Module
===END BdyCM DTC B124D:02-8A===
===BdyCM DTC B1D02:15-48===
Code: B1D02 - Left High Beam Circuit
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Body Control Module
===END BdyCM DTC B1D02:15-48===
===BdyCM DTC U3006:16-08===
Code: U3006 - Control Module Input Power A Circuit / Open
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC U3006:16-08===
===BdyCM DTC U3007:16-08===
Code: U3007 - Control Module Input Power B Circuit / Open
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC U3007:16-08===
===BdyCM DTC U3013:16-08===
Code: U3013 - Control Module Input Power C Circuit / Open
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC U3013:16-08===
===BdyCM DTC U3014:16-08===
Code: U3014 - Control Module Input Power D Circuit / Open
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC U3014:16-08===
===BdyCM DTC B115E:08-0A===
Code: B115E - Camera Module
Additional Fault Symptom:
- Bus Signal/Message Failures
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC B115E:08-0A===
===BdyCM DTC U0184:87-0A===
Code: U0184 - Lost Communication With Radio
Additional Fault Symptom:
- Missing Message
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC U0184:87-0A===
===BdyCM DTC B1438:03-08===
Code: B1438 - Battery Current Sensor
Additional Fault Symptom:
- Frequency Modulated / Pulse Width Modulated Failures
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC B1438:03-08===
===BECMB DTC None===
Successful DTC reading, no error codes found
Module: Battery Energy Control Module B
===END BECMB DTC None===
===FCIMB DTC U0257:00-0A===
Code: U0257 - Lost Communication With Front Controls / Display Interface Module
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Front Controls Interface Module B
===END FCIMB DTC U0257:00-0A===
===ATCM DTC U0100:00-0A===
Code: U0100 - Lost Communication With ECM/PCM A
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: All Terrain Control Module
===END ATCM DTC U0100:00-0A===
===RHVAC DTC None===
Successful DTC reading, no error codes found
Module: Rear Heating Ventilation Air Conditioning
===END RHVAC DTC None===
===OCS DTC U3003:16-28===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Occupant Classification System Module
===END OCS DTC U3003:16-28===
===OCS DTC B0061:12-28===
Code: B0061 - Passenger Seatbelt Tension Sensor
Additional Fault Symptom:
- Circuit Short To Battery
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Occupant Classification System Module
===END OCS DTC B0061:12-28===
===ABS DTC C0051:67-68===
Code: C0051 - Steering Wheel Position Sensor
Additional Fault Symptom:
- Signal Incorrect After Event
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Antilock braking system
Freeze Frame #1:
-EVENT_TIME: -185458372 s (Mon Apr 14 22:47:50 2025) - Event time
-TOTAL_DISTANCE: 201580 km - Total Distance
-MODULE_VOLTAGE: 13.8 V - Control Module Voltage
-OUTDOOR_TEMPERATURE: 11 °C - Outside temperature
-POWER_MODE: Running - Power Mode Status
-ABS: Inactive - ABS
-AYC: Inactive - AYC
-BTCS: Inactive - BTCS -201D
-HDC: Inactive - HDC
-RSC: Inactive - RSC
-BTC: Inactive - BTC
-VAC_BST_ST: Inactive - Active Vacuum Booster State
-BST_REL_SW: Inactive - Booster Release Switch State
-HYD_PMP_ST: Inactive - Hydraulic Pump State
-ECU_POWER_SUPPLY: 13.7 V - ECU Power Supply Voltage
-VSS: 67.0 km/h - Vehicle Speed
===END ABS DTC C0051:67-68===
===ABS DTC U3003:16-68===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Antilock braking system
Freeze Frame #1:
-POWER_MODE: Undefined - Power Mode Status
-ABS: Inactive - ABS
-AYC: Inactive - AYC
-BTCS: Inactive - BTCS -201D
-HDC: Inactive - HDC
-RSC: Inactive - RSC
-BTC: Inactive - BTC
-VAC_BST_ST: Inactive - Active Vacuum Booster State
-BST_REL_SW: Inactive - Booster Release Switch State
-HYD_PMP_ST: Inactive - Hydraulic Pump State
-ECU_POWER_SUPPLY: 6.9 V - ECU Power Supply Voltage
===END ABS DTC U3003:16-68===
===RTM DTC None===
Successful DTC reading, no error codes found
Module: Radio Transceiver Module
===END RTM DTC None===
===RCM DTC U0112:00-8B===
Code: U0112 - Lost Communication With Battery Energy Control Module B
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Restraint Control Module
===END RCM DTC U0112:00-8B===
===RCM DTC U3003:16-08===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Restraint Control Module
===END RCM DTC U3003:16-08===
===RCM DTC U0557:82-8B===
Code: U0557 - Invalid Data Received From Front Controls Interface Module A
Additional Fault Symptom:
- Alive/Sequence Counter Incorrect/Not Updated
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Restraint Control Module
===END RCM DTC U0557:82-8B===
===HVAC DTC U0140:00-0A===
Code: U0140 - Lost Communication With Body Control Module
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Heating Ventilation Air Conditioning
===END HVAC DTC U0140:00-0A===
===HVAC DTC U0401:82-48===
Code: U0401 - Invalid Data Received from ECM/PCM A
Additional Fault Symptom:
- Alive/Sequence Counter Incorrect/Not Updated
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Heating Ventilation Air Conditioning
===END HVAC DTC U0401:82-48===
===HVAC DTC B1083:07-08===
Code: B1083 - Recirculation Damper Motor
Additional Fault Symptom:
- Mechanical Failures
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Heating Ventilation Air Conditioning
===END HVAC DTC B1083:07-08===
===HVAC DTC B1B7D:14-08===
Code: B1B7D - Rear Air Distribution Actuator
Additional Fault Symptom:
- Circuit Short To Ground Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Heating Ventilation Air Conditioning
===END HVAC DTC B1B7D:14-08===
===PSCM DTC U3001:68-08===
Code: U3001 - Control Module Improper Shutdown Performance
Additional Fault Symptom:
- Event Information
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Power Steering Control Module
Freeze Frame #1:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: -780.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -12.8 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-MODULE_VOLTAGE: 11.0 V - Control Module Voltage
-ECU_INTERNAL_TEMPERATURE: 49 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 186.50 A - EPAS Motor Current
-PWR_MODE_KEY: Key Out - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
Freeze Frame #2:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: -780.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -12.8 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-MODULE_VOLTAGE: 10.8 V - Control Module Voltage
-ECU_INTERNAL_TEMPERATURE: 30 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 186.20 A - EPAS Motor Current
-PWR_MODE_KEY: Key Out - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
===END PSCM DTC U3001:68-08===
===PSCM DTC U3003:16-08===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Power Steering Control Module
Freeze Frame #1:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -0.7 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 87.10 ° - Steering Wheel Angle Alignment Offset
-TOTAL_DISTANCE: 201569 km - Total Distance
-MODULE_VOLTAGE: 7.5 V - Control Module Voltage
-ECU_POWER_SUPPLY: 7.7 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 0 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 0.70 A - EPAS Motor Current
-PWR_MODE_KEY: Key Recently Out - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
Freeze Frame #2:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -0.7 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 87.10 ° - Steering Wheel Angle Alignment Offset
-TOTAL_DISTANCE: 201569 km - Total Distance
-MODULE_VOLTAGE: 7.5 V - Control Module Voltage
-ECU_POWER_SUPPLY: 7.7 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 0 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 0.70 A - EPAS Motor Current
-PWR_MODE_KEY: Key Recently Out - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
===END PSCM DTC U3003:16-08===
===PSCM DTC U3003:68-08===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Event Information
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Power Steering Control Module
Freeze Frame #1:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -0.2 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-TOTAL_DISTANCE: 200531 km - Total Distance
-MODULE_VOLTAGE: 10.0 V - Control Module Voltage
-ECU_POWER_SUPPLY: 10.1 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 49 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 0.10 A - EPAS Motor Current
-PWR_MODE_KEY: Key Recently Out - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
Freeze Frame #2:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -0.2 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-TOTAL_DISTANCE: 200531 km - Total Distance
-MODULE_VOLTAGE: 10.0 V - Control Module Voltage
-ECU_POWER_SUPPLY: 10.1 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 49 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 0.10 A - EPAS Motor Current
-PWR_MODE_KEY: Key Recently Out - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
===END PSCM DTC U3003:68-08===
===PSCM DTC U0001:88-08===
Code: U0001 - High Speed CAN Communication Bus
Additional Fault Symptom:
- Bus Off
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Power Steering Control Module
Freeze Frame #1:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: 0.0 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-MODULE_VOLTAGE: 12.5 V - Control Module Voltage
-ECU_POWER_SUPPLY: 12.6 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 18 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 0.10 A - EPAS Motor Current
-PWR_MODE_KEY: Key Approved - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
Freeze Frame #2:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: 0.1 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-MODULE_VOLTAGE: 12.8 V - Control Module Voltage
-ECU_POWER_SUPPLY: 12.7 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 21 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: -0.50 A - EPAS Motor Current
-PWR_MODE_KEY: Key Recently Out - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
===END PSCM DTC U0001:88-08===
===PSCM DTC U0100:00-08===
Code: U0100 - Lost Communication With ECM/PCM A
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Power Steering Control Module
Freeze Frame #1:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -0.3 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-MODULE_VOLTAGE: 13.5 V - Control Module Voltage
-ECU_POWER_SUPPLY: 13.6 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 28 °C - ECU Internal Temperature
-PWR_MODE_KEY: Key Approved - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
Freeze Frame #2:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -0.3 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-MODULE_VOLTAGE: 13.5 V - Control Module Voltage
-ECU_POWER_SUPPLY: 13.6 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 28 °C - ECU Internal Temperature
-PWR_MODE_KEY: Key Approved - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
===END PSCM DTC U0100:00-08===
===PSCM DTC U0415:00-08===
Code: U0415 - Invalid Data Received from Anti-Lock Brake System (ABS) Control Module A
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Power Steering Control Module
Freeze Frame #1:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -0.3 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-TOTAL_DISTANCE: 200531 km - Total Distance
-MODULE_VOLTAGE: 13.5 V - Control Module Voltage
-ECU_POWER_SUPPLY: 13.5 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 28 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 0.50 A - EPAS Motor Current
-PWR_MODE_KEY: Key Approved - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
Freeze Frame #2:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 504.60 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -0.1 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: -505.00 ° - Steering Wheel Angle Alignment Offset
-TOTAL_DISTANCE: 201563 km - Total Distance
-MODULE_VOLTAGE: 14.0 V - Control Module Voltage
-ECU_POWER_SUPPLY: 14.0 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 35 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 0.00 A - EPAS Motor Current
-PWR_MODE_KEY: Key Approved - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
===END PSCM DTC U0415:00-08===
===ACM DTC U3003:16-08===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Audio Control Module
===END ACM DTC U3003:16-08===
===SCCM DTC None===
Successful DTC reading, no error codes found
Module: Steering Column Control Module
===END SCCM DTC None===
===IPC DTC U0100:00-0A===
Code: U0100 - Lost Communication With ECM/PCM A
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Instrument Panel Control Module
===END IPC DTC U0100:00-0A===
===IPC DTC U0138:82-0A===
Code: U0138 - Lost Communication with All Terrain Control Module
Additional Fault Symptom:
- Alive/Sequence Counter Incorrect/Not Updated
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Instrument Panel Control Module
===END IPC DTC U0138:82-0A===
===IPC DTC U3003:16-08===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Instrument Panel Control Module
===END IPC DTC U3003:16-08===
===GWM DTC U2100:00-2B===
Code: U2100 - Initial Configuration Not Complete
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Gateway Module A
===END GWM DTC U2100:00-2B===
===GPSM DTC U3003:16-88===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Global Positioning System Module
===END GPSM DTC U3003:16-88===
Recently Purchased a 2017 Ford Explorer Base 3.5 NA with 125k miles. Looking to fix it up but getting stumped on the issue before just “throwing” parts at it.
-Airbag Light on
-TPMS malfunction
-4wd malfunction service required
-Black radio screen
-HVAC heat stuck on - turns high once driving and cannot turn off.
I replaced the battery and tried resetting the BCM with no luck.
No visable damage to wires or signs of water entry from what I can tell.
Any help would be greatly appreciated !
Attached below were my ForSCAN results:
===PCM DTC P06E9:00-28===
Code: P06E9 - Engine Starter Performance
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Powertrain Control Module
Freeze Frame #1:
Freeze Frame #2:
-EVENT_TIME: -184447281 s (Sat Apr 26 15:39:21 2025) - Event time
-TOTAL_DISTANCE: 201874 km - Total Distance
-FUELSYS: Open Loop - Fuel System Status (Open/Closed Loop)
-LOAD: 0.00 % - Calculated Load Value
-ECT: 22 °C - Engine coolant temperature
-SHRTFT1: 0.00 % - Short term fuel trim 1
-LONGFT1: 3.91 % - Long term fuel trim 1
-SHRTFT2: 0.00 % - Short term fuel trim 2
-LONGFT2: 7.81 % - Long term fuel trim 2
-MAP: 98.0 kPa - Manifold absolute pressure sensor
-RPM: 0 1/min - Engine Revolutions Per Minute
-VSS: 0.0 km/h - Vehicle Speed
-SPARKADV: 0.00 ° - Spark Advance
-IAT: 22 °C - Intake Air Temperature
-RUNTM: 0 s - Time Since Engine Start
-EVAP_PCT: 0.00 % - Commanded Evaporative Purge
-FLI: 72.16 % - Fuel Level
-BARO: 98.0 kPa - Barometric pressure
-VPWR: 9.23 V - Control Module Voltage
-TP_REL: 5.88 % - Relative Throttle Position
-TAC_PCT: 9.41 % - Commanded Throttle Actuator Control
-RPMDSD: 1200 1/min - Desired Idle Speed RPM
-O2S12: 1.62 V - Heated Exhaust Gas Oxygen Sensor (bank 1, sensor 2)
-O2S22: 1.64 V - Heated Exhaust Gas Oxygen Sensor (bank 2, sensor 2)
-TQ_CNTRL: None Requested - Torque Control Requested
-APP_FLT: No Fault - Accelerator Pedal Position Sensor Status
-CHT_F: No Fault - Cylinder Head Temperature Sensor Status
-CHTIL: Off - Cylinder Head Temperature Indicator Lamp
-ETC_TRIM_LRN: Yes - Throttle Angle Offset has Learned
-IAT_F: No Fault - Inlet Air Temperature Sensor Status
-MISFIRE: No - Engine Misfire currently detected
-TP_F: No Fault - Throttle Position Sensor Status
-FF_LRND: No - Inferred Flex Fuel Learned
-MP_LRN: Yes - Misfire Profile Correction Learned
-MAF_F: No Fault - Mass Air Flow Sensor Status
-MAP_F: No Fault - Manifold Absolute Pressure Sensor Status
-OTS_STAT: Enabled - One-Touch Start Status
-SMC_MON: Off - Starter Motor Control Output Detected
-STRT_RLY: Disabled - Starter Motor Relay Enable
-APP1: 0.75 V - Accelerator pedal position sensor 1
-APP2: 0.38 V - Accelerator pedal position sensor 2
-TP1: 4.09 V - Throttle Position Sensor 1
-TP2: 1.24 V - Throttle Position Sensor 2
-GEAR: 1 - Gear Commanded
-GEAR_OSC: 1 - Gear Command by Output State Control
-TSS_SRC: 0 1/min - Actual Turbine Shaft Speed
-OSS_SRC: 0 1/min - Actual Output Shaft Speed
-TFT: 21 °C - Transmission Fluid Temperature
-TR: Park - Transmission range
===END PCM DTC P06E9:00-28===
===OBDII DTC None===
Successful DTC reading, no error codes found
Module: On Board Diagnostic II
===END OBDII DTC None===
===APIM DTC U0257:00-0B===
Code: U0257 - Lost Communication With Front Controls / Display Interface Module
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Accessory Protocol Interface Module
===END APIM DTC U0257:00-0B===
===APIM DTC U3003:16-08===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Accessory Protocol Interface Module
===END APIM DTC U3003:16-08===
===BdyCM DTC B124D:02-8A===
Code: B124D - Tire Pressure Sensor
Additional Fault Symptom:
- General Signal Failure
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Body Control Module
===END BdyCM DTC B124D:02-8A===
===BdyCM DTC B1D02:15-48===
Code: B1D02 - Left High Beam Circuit
Additional Fault Symptom:
- Circuit Short To Battery Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Body Control Module
===END BdyCM DTC B1D02:15-48===
===BdyCM DTC U3006:16-08===
Code: U3006 - Control Module Input Power A Circuit / Open
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC U3006:16-08===
===BdyCM DTC U3007:16-08===
Code: U3007 - Control Module Input Power B Circuit / Open
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC U3007:16-08===
===BdyCM DTC U3013:16-08===
Code: U3013 - Control Module Input Power C Circuit / Open
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC U3013:16-08===
===BdyCM DTC U3014:16-08===
Code: U3014 - Control Module Input Power D Circuit / Open
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC U3014:16-08===
===BdyCM DTC B115E:08-0A===
Code: B115E - Camera Module
Additional Fault Symptom:
- Bus Signal/Message Failures
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC B115E:08-0A===
===BdyCM DTC U0184:87-0A===
Code: U0184 - Lost Communication With Radio
Additional Fault Symptom:
- Missing Message
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC U0184:87-0A===
===BdyCM DTC B1438:03-08===
Code: B1438 - Battery Current Sensor
Additional Fault Symptom:
- Frequency Modulated / Pulse Width Modulated Failures
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Body Control Module
===END BdyCM DTC B1438:03-08===
===BECMB DTC None===
Successful DTC reading, no error codes found
Module: Battery Energy Control Module B
===END BECMB DTC None===
===FCIMB DTC U0257:00-0A===
Code: U0257 - Lost Communication With Front Controls / Display Interface Module
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Front Controls Interface Module B
===END FCIMB DTC U0257:00-0A===
===ATCM DTC U0100:00-0A===
Code: U0100 - Lost Communication With ECM/PCM A
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: All Terrain Control Module
===END ATCM DTC U0100:00-0A===
===RHVAC DTC None===
Successful DTC reading, no error codes found
Module: Rear Heating Ventilation Air Conditioning
===END RHVAC DTC None===
===OCS DTC U3003:16-28===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Occupant Classification System Module
===END OCS DTC U3003:16-28===
===OCS DTC B0061:12-28===
Code: B0061 - Passenger Seatbelt Tension Sensor
Additional Fault Symptom:
- Circuit Short To Battery
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Occupant Classification System Module
===END OCS DTC B0061:12-28===
===ABS DTC C0051:67-68===
Code: C0051 - Steering Wheel Position Sensor
Additional Fault Symptom:
- Signal Incorrect After Event
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Antilock braking system
Freeze Frame #1:
-EVENT_TIME: -185458372 s (Mon Apr 14 22:47:50 2025) - Event time
-TOTAL_DISTANCE: 201580 km - Total Distance
-MODULE_VOLTAGE: 13.8 V - Control Module Voltage
-OUTDOOR_TEMPERATURE: 11 °C - Outside temperature
-POWER_MODE: Running - Power Mode Status
-ABS: Inactive - ABS
-AYC: Inactive - AYC
-BTCS: Inactive - BTCS -201D
-HDC: Inactive - HDC
-RSC: Inactive - RSC
-BTC: Inactive - BTC
-VAC_BST_ST: Inactive - Active Vacuum Booster State
-BST_REL_SW: Inactive - Booster Release Switch State
-HYD_PMP_ST: Inactive - Hydraulic Pump State
-ECU_POWER_SUPPLY: 13.7 V - ECU Power Supply Voltage
-VSS: 67.0 km/h - Vehicle Speed
===END ABS DTC C0051:67-68===
===ABS DTC U3003:16-68===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Antilock braking system
Freeze Frame #1:
-POWER_MODE: Undefined - Power Mode Status
-ABS: Inactive - ABS
-AYC: Inactive - AYC
-BTCS: Inactive - BTCS -201D
-HDC: Inactive - HDC
-RSC: Inactive - RSC
-BTC: Inactive - BTC
-VAC_BST_ST: Inactive - Active Vacuum Booster State
-BST_REL_SW: Inactive - Booster Release Switch State
-HYD_PMP_ST: Inactive - Hydraulic Pump State
-ECU_POWER_SUPPLY: 6.9 V - ECU Power Supply Voltage
===END ABS DTC U3003:16-68===
===RTM DTC None===
Successful DTC reading, no error codes found
Module: Radio Transceiver Module
===END RTM DTC None===
===RCM DTC U0112:00-8B===
Code: U0112 - Lost Communication With Battery Energy Control Module B
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Restraint Control Module
===END RCM DTC U0112:00-8B===
===RCM DTC U3003:16-08===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Restraint Control Module
===END RCM DTC U3003:16-08===
===RCM DTC U0557:82-8B===
Code: U0557 - Invalid Data Received From Front Controls Interface Module A
Additional Fault Symptom:
- Alive/Sequence Counter Incorrect/Not Updated
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Restraint Control Module
===END RCM DTC U0557:82-8B===
===HVAC DTC U0140:00-0A===
Code: U0140 - Lost Communication With Body Control Module
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Heating Ventilation Air Conditioning
===END HVAC DTC U0140:00-0A===
===HVAC DTC U0401:82-48===
Code: U0401 - Invalid Data Received from ECM/PCM A
Additional Fault Symptom:
- Alive/Sequence Counter Incorrect/Not Updated
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
- Test not complete
Module: Heating Ventilation Air Conditioning
===END HVAC DTC U0401:82-48===
===HVAC DTC B1083:07-08===
Code: B1083 - Recirculation Damper Motor
Additional Fault Symptom:
- Mechanical Failures
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Heating Ventilation Air Conditioning
===END HVAC DTC B1083:07-08===
===HVAC DTC B1B7D:14-08===
Code: B1B7D - Rear Air Distribution Actuator
Additional Fault Symptom:
- Circuit Short To Ground Or Open
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Heating Ventilation Air Conditioning
===END HVAC DTC B1B7D:14-08===
===PSCM DTC U3001:68-08===
Code: U3001 - Control Module Improper Shutdown Performance
Additional Fault Symptom:
- Event Information
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Power Steering Control Module
Freeze Frame #1:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: -780.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -12.8 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-MODULE_VOLTAGE: 11.0 V - Control Module Voltage
-ECU_INTERNAL_TEMPERATURE: 49 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 186.50 A - EPAS Motor Current
-PWR_MODE_KEY: Key Out - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
Freeze Frame #2:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: -780.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -12.8 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-MODULE_VOLTAGE: 10.8 V - Control Module Voltage
-ECU_INTERNAL_TEMPERATURE: 30 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 186.20 A - EPAS Motor Current
-PWR_MODE_KEY: Key Out - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
===END PSCM DTC U3001:68-08===
===PSCM DTC U3003:16-08===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Power Steering Control Module
Freeze Frame #1:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -0.7 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 87.10 ° - Steering Wheel Angle Alignment Offset
-TOTAL_DISTANCE: 201569 km - Total Distance
-MODULE_VOLTAGE: 7.5 V - Control Module Voltage
-ECU_POWER_SUPPLY: 7.7 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 0 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 0.70 A - EPAS Motor Current
-PWR_MODE_KEY: Key Recently Out - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
Freeze Frame #2:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -0.7 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 87.10 ° - Steering Wheel Angle Alignment Offset
-TOTAL_DISTANCE: 201569 km - Total Distance
-MODULE_VOLTAGE: 7.5 V - Control Module Voltage
-ECU_POWER_SUPPLY: 7.7 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 0 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 0.70 A - EPAS Motor Current
-PWR_MODE_KEY: Key Recently Out - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
===END PSCM DTC U3003:16-08===
===PSCM DTC U3003:68-08===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Event Information
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Power Steering Control Module
Freeze Frame #1:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -0.2 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-TOTAL_DISTANCE: 200531 km - Total Distance
-MODULE_VOLTAGE: 10.0 V - Control Module Voltage
-ECU_POWER_SUPPLY: 10.1 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 49 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 0.10 A - EPAS Motor Current
-PWR_MODE_KEY: Key Recently Out - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
Freeze Frame #2:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -0.2 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-TOTAL_DISTANCE: 200531 km - Total Distance
-MODULE_VOLTAGE: 10.0 V - Control Module Voltage
-ECU_POWER_SUPPLY: 10.1 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 49 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 0.10 A - EPAS Motor Current
-PWR_MODE_KEY: Key Recently Out - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
===END PSCM DTC U3003:68-08===
===PSCM DTC U0001:88-08===
Code: U0001 - High Speed CAN Communication Bus
Additional Fault Symptom:
- Bus Off
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Power Steering Control Module
Freeze Frame #1:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: 0.0 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-MODULE_VOLTAGE: 12.5 V - Control Module Voltage
-ECU_POWER_SUPPLY: 12.6 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 18 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 0.10 A - EPAS Motor Current
-PWR_MODE_KEY: Key Approved - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
Freeze Frame #2:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: 0.1 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-MODULE_VOLTAGE: 12.8 V - Control Module Voltage
-ECU_POWER_SUPPLY: 12.7 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 21 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: -0.50 A - EPAS Motor Current
-PWR_MODE_KEY: Key Recently Out - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
===END PSCM DTC U0001:88-08===
===PSCM DTC U0100:00-08===
Code: U0100 - Lost Communication With ECM/PCM A
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Power Steering Control Module
Freeze Frame #1:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -0.3 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-MODULE_VOLTAGE: 13.5 V - Control Module Voltage
-ECU_POWER_SUPPLY: 13.6 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 28 °C - ECU Internal Temperature
-PWR_MODE_KEY: Key Approved - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
Freeze Frame #2:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -0.3 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-MODULE_VOLTAGE: 13.5 V - Control Module Voltage
-ECU_POWER_SUPPLY: 13.6 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 28 °C - ECU Internal Temperature
-PWR_MODE_KEY: Key Approved - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
===END PSCM DTC U0100:00-08===
===PSCM DTC U0415:00-08===
Code: U0415 - Invalid Data Received from Anti-Lock Brake System (ABS) Control Module A
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Power Steering Control Module
Freeze Frame #1:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 0.00 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -0.3 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: 3276.70 ° - Steering Wheel Angle Alignment Offset
-TOTAL_DISTANCE: 200531 km - Total Distance
-MODULE_VOLTAGE: 13.5 V - Control Module Voltage
-ECU_POWER_SUPPLY: 13.5 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 28 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 0.50 A - EPAS Motor Current
-PWR_MODE_KEY: Key Approved - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
Freeze Frame #2:
-STEER_FEEL: Comfort - Steering Personalization Status
-SWRS: 0 1/min - Steering Wheel Rotation Speed
-SW_ANGLE: 504.60 ° - Steering Wheel Angle
-SSHFT_TQ_S2: -0.1 Nm - Steering Shaft Torque Sensor #2
-SW_ALIGN_OFSET: -505.00 ° - Steering Wheel Angle Alignment Offset
-TOTAL_DISTANCE: 201563 km - Total Distance
-MODULE_VOLTAGE: 14.0 V - Control Module Voltage
-ECU_POWER_SUPPLY: 14.0 V - ECU Power Supply Voltage
-ECU_INTERNAL_TEMPERATURE: 35 °C - ECU Internal Temperature
-EPAS_MOTOR_CUR: 0.00 A - EPAS Motor Current
-PWR_MODE_KEY: Key Approved - Power Mode Key State
-VSS: 0.0 km/h - Vehicle Speed
===END PSCM DTC U0415:00-08===
===ACM DTC U3003:16-08===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Audio Control Module
===END ACM DTC U3003:16-08===
===SCCM DTC None===
Successful DTC reading, no error codes found
Module: Steering Column Control Module
===END SCCM DTC None===
===IPC DTC U0100:00-0A===
Code: U0100 - Lost Communication With ECM/PCM A
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Instrument Panel Control Module
===END IPC DTC U0100:00-0A===
===IPC DTC U0138:82-0A===
Code: U0138 - Lost Communication with All Terrain Control Module
Additional Fault Symptom:
- Alive/Sequence Counter Incorrect/Not Updated
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Instrument Panel Control Module
===END IPC DTC U0138:82-0A===
===IPC DTC U3003:16-08===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Instrument Panel Control Module
===END IPC DTC U3003:16-08===
===GWM DTC U2100:00-2B===
Code: U2100 - Initial Configuration Not Complete
Status:
- DTC Present at Time of Request
- Malfunction Indicator Lamp is Off for this DTC
Module: Gateway Module A
===END GWM DTC U2100:00-2B===
===GPSM DTC U3003:16-88===
Code: U3003 - Battery Voltage
Additional Fault Symptom:
- Circuit Voltage Below Threshold
Status:
- Previously Set DTC - Not Present at Time of Request
- Malfunction Indicator Lamp is On for this DTC
Module: Global Positioning System Module
===END GPSM DTC U3003:16-88===
