Change Keypad code?

[liv2surf34]

Is there anyway to change the keypad code. I know my current one but one of my friends thought it would be funny to watch me enter it and now I would like to change it. Anyone?

 

[huskyfan23]

Get a new RAP module or change the resistor positions around on the module. Can you solder?

 

[aldive]

Is there anyway to change the keypad code. I know my current one but one of my friends thought it would be funny to watch me enter it and now I would like to change it. Anyone?

Do you want to change the perminant factory code or the code that can be reset?

 

[jerrypar72]

I recently bought a 2001 Explorer Sport. I can't find the keypad code in the jack compartment. The box is yellow and not gray. Am I looking in the wrong place?

 

[huskyfan23]

I recently bought a 2001 Explorer Sport. I can't find the keypad code in the jack compartment. The box is yellow and not gray. Am I looking in the wrong place?

That's the right box, now find the sticker on it.

 

[TSTONE]

Nope you are looking in the right place its just way up in there - I use to reach in and grab the module pulling it towards the rear bending the bracket slightly, then take a flashlight and if you look at just the right angle you can read the code.

 

[jerrypar72]

The yellow box is not a module, its a box that the left rear seat belt winds up into. I can't move it enough to see a code on it. I saw on another thread that the code is under the defrost grill on top of the dashboard? But I don't want to damage that grill trying to remove it.
This is a PITA!!! LOL I don't want to pay the dealership to put the truck on the computer just to get this code, and pay them friggin $65.00.

 

[Robb]

Yes, the '01 Sport's code is in a different spot. Can I remember where right now? Nope. Try using the search feature for "keyless entry sport", you will find a couple of threads about it.

 

[liv2surf34]

I just would like to change the code that you type in on the outside, how do i do that?

 

[huskyfan23]

Hm. Thought the yellow box was the module. Maybe in other years. Isn't there a master code? I think the manual tells you how to change the code. I remember some post saying you can only add codes, not change the factory one.

 

[liv2surf34]

O ok, well I will check the manual on how to add a code, wish i could delete the old one though

 

[Electrohacker]

type the factory code, press 2 then type your personal code... you cannot over write the factory code but everytime you set a new personal ocde it overwrites the previous personal code... to find the factory code you have to get the number off the computer... (there's also a spot in the maual for the owner to write it in, maybe the previous owner did)

 

[liv2surf34]

Ok thanks man

 

[jnason]

Try this site I think it is the same for an Explorer.

www.ford150net/howto/keypad1.php

 

[Robb]

Even when you fix that link with the ".net", the link is junk.

 

[huskyfan23]

http://www.fordf150.net/howto/keypad1.php

 

[4FordFamily]

I cracked the code! (no pun intended)
the link was supposed to look like this
http://www.fordf150.net/howto/keypad1.php

http://www.fordf150.net/howto/keypad1.php

 

[4FordFamily]

damnit you beat me by 10 seconds!

 

[huskyfan23]

I cracked the code! (no pun intended)
the link was supposed to look like this
http://www.fordf150.net/howto/keypad1.php

http://www.fordf150.net/howto/keypad1.php

Great minds think alike