TarHeel085's Coilover swap

[TarHeel085]

so i see you talked rcd into selling the mount.. but for 100 i think its kind of steep. is that 3/16 steel?

haha, yeah i worked my magic on them! but your right $100 is lil steep, but man, they are thick, im pretty sure they are 3/16" i just dont have the time or resources to make them. but i ordered my springs 800lb Eibachs (blue ) and my other shock for cheaper then any place i found online. should be here next friday or so. gunna get gusseting sometime next week. so i should be good to go.

BTW zhanx, does anyone down your way want a dry nitrous kit, or you maybe

 

[zhanx]

umm no on the nitrous...

hey i found out something today that might affect your build. I changed out my front shocks last week for longer travel ones. Well today i noticed a spot under the truck in the drive way.. well two of them. I slide under and i was leaking at my seals. seems the new shocks can pull out the cv axle stub from the axle. I am gonna look into slip jointing the cv shafts. You might need to also. This should help prevent them from being pulled out and cause the axle to leak etc..

 

[TarHeel085]

really? as many times as ive had my front at full droop, with no shocks, i havent seen that. it sucks though! but mine isnt gunna be long travel, its actually gunna be almost EXACTLY the same as stock in terms of droop and travel, so i shouldnt have to worry about that. i was kinda hopin that your limit strap thread would get more replys, cause im gunna have to get some to, if you end up ordering some let me know where you plan to mount them and how, cause i will need to do the same thing!!

BTW i figured out how to get the coils on, the bottom retainer comes off and the coil slides on.

 

[zhanx]

i am gonna measure up them on monday and order them i'll let you know how it goes.

 

[TarHeel085]

i am gonna measure up them on monday and order them i'll let you know how it goes.

so how did it go man?

 

[zhanx]

It didn't. spent the day looking for a wire short in my lightning. turned out that the starter is going bad (i have very high compression in it).

It was acting like the battery was drained. I'd jump it and it would start, so i swapped in a new battery. Worked so i was like cool shut it off went inside to use the bathroom came out to move vehicles and it wouldn't start. just a click. After half a day of looking for a wire short, i had a duh, check the battery with the multimeter it was at 12.8 volts and pulled the starter. I could move the gear by hand so i took to Autozone it passed the test like 10 times. Replaced it anyways, everthing is good. So tommorrow I will measure. I am thinking i will need about 20-24" straps maybe a little less.

I am gonna mount them low to begin with and after they strech move them up. I am gonna try for center on the arms as possible. Check my other thread for a new question on them.

 

[TarHeel085]

well, i got my springs, 900lb Hypercoils, not sure what went wrong. but anyway, ill see how they work, they might just be exactly what im lookin for, but theres no way to know untill i get them on. and also ordered some 15" limit straps.

 

[zhanx]

hurry up and install those things so i can see it all ready

 

[V8BoatBuilder]

I want to know how this turns out - I'd love to ditch the t-bars for some coilovers.

 

[TarHeel085]

ill be putting them in tommorow if the weather holds out!!

 

[TarHeel085]

SOB these are a pain to put in! im havin some fairly substantial problems, first i had to trim the hell outta the bump stop. the spring only has about 1/4" clearance between the frame, at complete full droop the control arm smacks the springs. so the limit straps are a COMPLETE must to have when doing this. i made up some bracing for the upper conversion mount that i need to weld up. still need to make bracing for the shcok tower. i also had to relocate the brake line on the frame. i still need to trim the bump stop bracket more. and see if i can move the top out a little more to get more clearance, and then mount my straps when they come in the first pic is somewhat compressed, the last one is where full droop needs to be.

 

[IZwack]

Man I think you got the wrong shocks - they look like they're made from paper

 

[zhanx]

blue i like blue

 

[TarHeel085]

lol, yeah they are paper mache', but thats just to protect my springs. random question, what is the unsprung weight for each side?

 

[Hartman]

I need updates!

 

[redranger4.0]

so i see you talked rcd into selling the mount.. but for 100 i think its kind of steep. is that 3/16 steel?

hmm its wierd that they give people a hard time about buying brackets. I had to get some replacement brackets for my lift when i sold it. i didnt even have to give them the serial number, jsut told them what i need and they sent it out.

 

[FROADER]

Alright, I see you're online right now. Updates?

 

[MountaineerGreen]

Alright, I see you're online right now. Updates?

x2

 

[TarHeel085]

alright, heres the deal, in between being a full time student, work, and gettin a different car in addition to the explorer this project is sort of on the back burner. hopefully around christmas time ill have this project completed. i hate that ive had to delay it this long, but its just one of those things that i couldnt avoid. updates as soon as they become availible.

 

[dkchrist]

sweet i just put on the rcd lift this summer and it rocks smooth ride and nice look now if i only had bigger tire...