Search results

Plastic welding- Has anyone have any experience with welding PA6+ PPE. I am trying make a repair. Does anyone know what is the best method too uses?

I have a Compact spare tire, that's 28 years old. Went too use it last week, and need air, call triple A , they fill it, and when I went to drive away making a turn, the tire deflated. The next day I try too fill it, it went too 10 psi, then deflated. Look at the tire, I did not see any holes...

For the 1995 to 1997 Outside ambient air temperature sensor for the overhead console are no longer available. The 1998 and newer (2008), maybe newer are all the same. I ordered a replacement sensor and received the new sensor (standard Part# tx12). Too used this sensor you need to order the plug...

Does anyone else on this forum have a problem with the blue text font?

Does anyone know how too remove the finger oil stain on the rear view mirror?

Is there a easy way of adjusting and alignment the new door strike bushing after replacement? R there some do's and don't?

Neutral switch adjustment- 1995 explorer 4 door. I replaced my Neutral switch a few ago. This year I noticed the reverse lights did not come on. So this year I made sure the alignment marks on the Neutral switch, where in alignment. Backup lights were illuminated. Now they are not. So today I...

Does anyone know, what happens too the cooling system, when you change the coolant pressure cap from 16 psi to 21 psi? The correct term is coolant tank expansion cap.

Replacement rear diff fill plug! Where do you buy a new one for 95? Are all the rear diff Fill plug the same for all the years? Are all the rear diff Fill plug the same for all the makes and model fords?

Is there a spring on the hood? My hood does not pop open. The hood latch (lock) works fine with the hood open; when I lock and unlock the latch

I just replaced the oil pressure switch for the gauge. I used motorcraft SW-2220 (E9SZ-9278A). Torque 12 -18 ft/#(FSM). I used a oil pressure switch socket(from autozone). What I checked before replacement, Is how it worked. Result are: if I grounded the wire the gauge showed 1/2 way on the...

I am repairing some steel tubing and I am using flare fitting and brass union (coupling) too joint the lines. I purchase pre-fab brake tube with flare fitting that are steel and also the mating brass union. Problem I am having the steel fitting are leaking at the connection. Has anyone else...

What is everyone doing for replacing factory pin stripe?

Is there a cover below the driver rear quarter panel fuel filler area? my 95 ex is rusted out. What i found was the filler neck is in a plastic dugout, which is inside a half dome. The half dome is rusted thru. the area by the filler neck rusted thru and the wheel well. If there was a cover or...

General question . Radiator oil Cooler plugs and adapter. Does anyone know where you would buy the plugs and hard line adapter?

I've got an odd Coolant leak on a 95 4.0L OHV. My 'ex is leaking on the oil filter side of the engine (above filter), Below the heater valve, hoses in and out heater core. The heater valve and hoses are dry. I'm having a problem pin pointing the leak of the engine. I cant where it coming from...

1995 2nd gen 4x4 low stop working. It worked, than did not work. Now its not working. I replaced the GEM module, selector switch, and transfer case shift motor. No change. Still have the issue. From this forum, someone states, there is a additional relay in the dash, that commands the GEM...

I am looking for the thread for 4x4 troubleshooting procedure. Someone on this forum posted a procedure on how each generation explorer 4x4 system operates. I can't seem too found it again.

What is everyone doing for rack and pinion? I have a 1995 explorer xlt4 door. Do maintenance item today a inspected the boot on tie rod, and there is fluid inside. This my third replacement. Replaced it 3 years ago or 3k mile ago and its leaking ago.

What is everyone using for replacement braided ground wires, and clips on a 2nd gen XLT

Change my transmission fluid the other day with MERCON V. On the Val bottle there was a tech support number so I call it and ask the tech support, can MERCON V be used in transfer case He answer YES, and also MAXLIFE.

The ABS light is on, on my 95 XLT, OBD I , how do read the code, and with what scanner did you use?

Does anyone know the part number for the capacitor on the ignition coil (radio capacitor) for a 95 XLT exp

Does anyone know what a I.R.C.M. tester is? Thanks pete

Has anyone had a problem with there neutral switch that they replaced did not last a long time? My replacement only lasted 3 year and now its acting up again.

Today’s Date 12-11-2019 1993 to 1995 ford explorer xlt 4 door Code X (Cam Position Sensor) Cam Synchronizer Replacement. On My 1995 ford Explorer 4.0L V6 OVH pushrod engine;I used Cardone A1 84-S2605New Synchronizer. Tools 1. Rockauto Cardone 84-S2605 (Ford Part # 12K073) 2. Ebay: CID...

Replacing cam position sensor on a 93-95 explorer 4.0L ohv,has anyone done one. Do you need to remove the manifolds?