M90 rebuild (rudy)

[4pointslow]

Pictures Please! Its got to feel like Christmas time at your place, lol!
Can you imagine engines and parts under your tree? I can . LOL

 

[jd4242]

Pictures Please! Its got to feel like Christmas time at your place, lol!
Can you imagine engines and parts under your tree? I can . LOL

Im excited but same time im pretty frustrated at him..he was not there when i picked it up, his appendix burst so he's in the hospital. .i talked to the other machinist but he didnt know much..

The block surface looks like poo still and i swear the block doesnt look like it was cleaned before he assembled it..it also is missing the freeze plugs and the plug in the back for the cam..

Then the heads are rusted all up from sitting around..

Just looks like he didnt put alot of effort into the build..

Didnt have time to take any pictures and wanna clean everything up before i take any pics..

 

[jd4242]

Well went by and took some quick pictures. .also talked to some other racers about the copper gaskets and what they do..couple have said they use the utra black and caot the whole gasket and that has worked better than copper spray especially if the surfaces are not perfectly smooth..they all said my surfaces arnt that bad and they will be fine..said you can tell they've been milled and are plenty flate enough, just clean them up real good and coat the gaskets. ..
Said oring will keep the compression in and the utra black will seal the water,no crazy pressure there

 

[jd4242]

Some pics..gota clean everything up

 

[jd4242]

Well things got a little more serious. .picked up a set of Hoosier R7 slicks..paid $40..they are a little small at 295/30/18 but will do for now..lol

 

[4pointslow]

Bottom end looks real nice! Hope those tire help get you some needed traction.

 

[jd4242]

So went to drive the truck after blowing up the aviator and smelt gas BAD...all my fuel lines have failed. .the ethanol has eatn them up..when i purchased the -6an line there was no warning and they still say they work with gasoline. .well they dont and summit wont do anything about it..

So im forced to replace all my line with -6an SS PTFE lines and if that wasnt bad enough, all the fittings have to be replaced to work with a PTFE SS hose..so now i dont have a vehicle to drive for another week and im out $284.64 for lines that i shouldn't have had to replace. .

Was makes me even more mad is the asshole i talked to at summit about it and the idea of what that decaying line did to my filter or injectors. ...im PISSED to say least

The parts i had to replace. .

 

[jd4242]

Just thought of something else..i maybe totally screwed. .i dont think i can get to the rear line on the fuel rail WITHOUT REMOVING MY SUPERCHARGER! !! Mannnn !!! It would cost me $120 in gaskets just to take that off..no way am i pulling that off till it goes on new motor!!

 

[Dono]

2 down. ****

Sorry.

Starts t become a real issue when your down 2 vehicles.

 

[jd4242]

Got my parts from Tom but haven't gotten the rockers yet,should be here tomorrow. .

I will say im slightly concerned about his recent changes for added strength. .if you view this picture/diagram you can see he has added two bolts that hold down the cylinder head, to support his rocker mount bar..the 2 bolts are 10.9 metric bolts that have be drilled and tapped through the top of the bolt head..he said he hasnt found a ARP stud yet to use so this was his quick solution. .to me,drilling in the head of the bolt is going to weaken that bolt drastically. .im going to try and find possibly a longer 10.9 bolt to go through his support bar,the spacer and then into the head..i think that would be stronger..going to try ARP but i assume they have nothing as he said he has..

Any input on this??

^^^^FYI these are his 10.9 head bolts that dont require replacement. .

Another thing,if you look at this picture you can see he has countersunk the last stud on this plate..dont know why but i think it would make the stud weaker as it has less thread...i emailed him asking for a reason..

Last he said his pushrods were adjustable, the ones i received are not..again i asked why..i will need adjustable ones or to measure which i pointed out before ordering. .

No word on the copper gaskets yet,machine shop still has all my parts waiting

So spoke with him..he said he tried to find a longer bolt but couldn't and swears it will be fine..

Well it would've been but the spacer he sent is too small.also the holes he drilled into the head bolts are not straight! !!haven't called him back about it because i decided to do my own thing..

So i took some measurements and called ARP..they found a bolt in the exact size i needed with a 200,000 psi rating,same as my studs..next i ordered some hardened tube(A513 DOM) with a OD-0.875" x WALL-0.188" x ID- 0.499" to make spacers..it will go through his plate,the spacers and into the head..should be much stronger..

Also received my rollers today

So as some have known I've been talking to Tom..he has told me he has a updated plate and hardware. .to send the old one back and he would replace it..well finally got a hold of him on the phone today and he is using the same thing i was going to..a larger spacer and a arp bolt to go through the plate,then spacer and into the head..so im sending my parts back today..ill update when i receive them..

 

[jd4242]

Got the lines swapped out..what a PIA..completely ran outa gas so gota wait till the morning to get on base to get some ethanol. .

Tell you one thing..i sureeeeee miss the rumble of this truck,thing sounds MEAN!! And the neighbors hate me!!

 

[mr cribb]

Sorry to hear about your troubles. Did your kiddo arrive? (Forgive me it's been quite some time since I've followed your thread).

 

[jd4242]

Sorry to hear about your troubles. Did your kiddo arrive? (Forgive me it's been quite some time since I've followed your thread).

Yea turn 1 last Saturday. .lol

 

[mr cribb]

Yea turn 1 last Saturday. .lol

Awesome. Boy or girl?
My oldest is 14 (boy) and youngest is 5 (girl)

 

[jd4242]

Awesome. Boy or girl?
My oldest is 14 (boy) and youngest is 5 (girl)

Boy..big boy

 

[jd4242]

As my luck goes...the rear end came up and bottomed out,smashing my feed line..i now how a leak and no extra line..fml

 

[Dono]

And, still no vehicle.
Rear end came up and smashed the line?
At least you found a weak spot. When you re-do, you can re-route.

Ah, the modification game. We are all insane.

 

[jd4242]

As my luck goes...the rear end came up and bottomed out,smashing my feed line..i now how a leak and no extra line..fml

And, still no vehicle.
Rear end came up and smashed the line?
At least you found a weak spot. When you re-do, you can re-route.

Ah, the modification game. We are all insane.

Yea the pumpkin came up and the very corner smashed into the bed,just happened the line was there..its never done that before..yea gona reroute it for sure,atleast it was a short 2ft feed line going to my filter and not a 13ft line..

Ordered 3ft and should be here Tuesday. .i used every inch of the 30ft i ordered

 

[Dono]

I know your plate is pretty full, and you really don't need to be re-doing things you just did.
We can all relate.

 

[jd4242]

Well got my new line today,went to take off the ""reusable"" fitting and they definitely are not ""reusable ""..the inside ferrule was crushed. .i manage to get one around again but the second one would not..it ended up stripping the fitting out..i had no choice but to cross thread it and use it so its leaking..ive ordered new fitting from summit AGAIN. .

IM about fed up with summit. .FIRST i buy $300 worth of lines and fittings thats sold for gasoline but cant be used with gasoline. .so then have to replace ALL the lines and fittings that are sold as ""REUSABLE "" BUT cant be reused!!

Then the customer service guy was a straight asshole also and told me everything will fail..well why would i buy something if its GUARANTEE to fail..

Things are getting out of control for cost..between my 3 trucks i could have had a new Ferrari by now and sad part is I'm not even kidding :-(